The unload process currently tells each TCP/TLS to terminate but
does not wait for them to do so. This introduces a race condition
where the container holding the threads may be destroyed before
the threads are able to remove themselves from it. When they
finally do the container is invalid and can't be used causing a
crash.
A previous change existed which waited a bit to wait for any
stranglers to finish. This change extends this and waits longer.
ASTERISK-25961 #close
Change-Id: Idc6262b670ca49ede32061159e323b7b63c6f3c6
Since Stasis has been introduced, an attempt to send AMI messages by an
autocreated peer caused a crash, and all events from autocreated peers were
semi-inadvertently disabled altogether in 0b83761. This change restores the
disabled functionality.
ASTERISK-25950
Change-Id: Iecc350f23db603fadb2f302064643ebe9664e974
Added the ability to show channel statistics to chan_pjsip (cli_functions.c)
Moved the existing 'pjsip show channel(s)' functionality from
pjsip_configuration to cli_functions.c. The stats needed chan_pjsip's
private header so it made sense to move the existing channel commands as well.
Now using stasis_cache_dump to get the channel snapshots rather than retrieving
all endpoints, then getting each one's channel snapshots. Much more efficient.
Change-Id: I03b114522126d27434030b285bf6d531ddd79869
Asterisk 13.7.0 included a fix for ASTERISK-24543, not to send all those
codecs, which the caller did not request/support. That fix was not complete
because on the second Session Timer all codecs were sent again. Some VoIP/SIP
clients interpreted that complete codec-list as a change in the SIP session.
Because of that, Asterisk did not send the RTP audio via NAT anymore which
created a non-audio scenario after the second Session Timer fired.
ASTERISK-24543 #close
Change-Id: I1881827816ab7fd47eb4287a95961179b34a0b66
check_via() already skips leading blanks where the sent-by address (with the
optional port) should be placed.
Since RFC 3261 allows for blanks between the port ant the Via parameters:
> https://tools.ietf.org/html/rfc3261#section-20.42
(actually it allows a lot of blanks more ;-)). I just switched from
ast_skip_blanks() to ast_strip() on the local copy of the string.
ASTERISK-21301 #close
Change-Id: Ie5b8fe5a07067b7c0dc9bcdd1707e99b23b02b06
During a transfer involving direct media a race occurs between when the
transferer channel is swapped out, initiating rtp changes/updates, and the
subsequent reinvites.
When Alice, after speaking with Charlie (Bob is on hold), connects Bob and
Charlie invites are sent to each in order to establish the call between them.
Bob is taken off hold and Charlie is told to have his media flow through
Asterisk. However, if before those invites go out the bridge updates Bob's
and/or Charlie's rtp information with direct media data (i.e. address, port)
then the invite(s) will contain the remote data in the SDP instead of the
Asterisk data.
The race occurs in the native bridge glue code when updating the peer. The
direct_media_address can get set twice before sending out the first invite
during call connection. This can happen because the checking/setting of the
direct_media_address happened in one thread while the sending of the invite(s)
happened in another thread.
This fix removes the race condition by moving the checking/setting of the
direct_media_address to be in the same thread as the sending of the invites(s).
This serializes the checking/setting and sending so they can no longer happen
out of order.
ASTERISK-25849 #close
Change-Id: Idfea590175e74f401929a601dba0c91ca1a7f873
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023 #close
Change-Id: I96d429c57a48861fd8bde63dd93db4e92dc3adb6
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: I2e40de89efc8ae6e8850771d089ca44bc604b508
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: If595e4456cd059d7171880c7f354e844c21b5f5f
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: I9c11b9d597468f63916c99e1dabff9f4a46f84c1
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
* Fix retrans_pkt() to call check_pendings() with both the owner channel
and the private objects locked as required.
* Refactor dialog retransmission packet list to safely remove packet
nodes. The list nodes are now ao2 objects. The list has a ref and the
scheduled entry has a ref.
ASTERISK-25023
Change-Id: I50926d81be53f4cd3d572a3292cd25f563f59641
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
* Made always run check_pendings() under the scheduler thread so scheduler
ids can be checked safely.
ASTERISK-25023
Change-Id: Ia834d6edd5bdb47c163e4ecf884428a4a8b17d52
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: I6d65269151ba95e0d8fe4e9e611881cde2ab4900
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
* Fix clearing autokillid in __sip_autodestruct() even though we could
reschedule.
ASTERISK-25023
Change-Id: I450580dbf26e2e3952ee6628c735b001565c368f
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: I98a694fd42bc81436c83aa92de03226e6e4e3f48
This patch is part of a series to resolve deadlocks in chan_sip.c.
* Make dialog_unlink_all() unschedule all items at once in the sched
thread.
ASTERISK-25023
Change-Id: I7743072fb228836e8228b72f6dc46c8cc50b3fb4
This patch is part of a series to resolve deadlocks in chan_sip.c.
The reordering of chan_sip's shutdown is to handle any immediate events
that get put onto the scheduler so resources aren't leaked. The typical
immediate events at this time are going to be concerned with stopping
other scheduled events.
ASTERISK-25023
Change-Id: I3f6540717634f6f2e84d8531a054976f2bbb9d20
This patch is part of a series to resolve deadlocks in chan_sip.c.
Delaying destruction of the chan_sip sip_pvt structures caused the
/channels/chan_sip/test_sip_rtpqos unit test to crash. That test
registers a special test ast_rtp_engine with the rtp engine module. When
the unit test completes it cleans up by unregistering the test
ast_rtp_engine and exits. Since the delayed destruction of the sip_pvt
happens after the unit test returns, the destructor tries to call the rtp
engine destroy callback of the test ast_rtp_engine auto variable which no
longer exists on the stack.
* Change the test ast_rtp_engine auto variable to a static variable. Now
the variable can still exist after the unit test exits so the delayed
sip_pvt destruction can complete successfully.
ASTERISK-25023
Change-Id: I61e34a12d425189ef7e96fc69ae14993f82f3f13
Remove destructor calling destroy_it calling really_destroy_it
for no benefit. Just make the destructor the really_destroy_it
function.
Change-Id: Idea0d47b27dd74f2488db75bcc7f353d8fdc614a
Previous chan_sip behavior:
Before this patch chan_sip would always strip any quotes from an incoming
reason and pass that value up as the REDIRECTING(reason). For an outgoing
reason value, chan_sip would check the value against known values and
quote any it didn't recognize. Incoming 480 response message reason text
was just assigned to the REDIRECTING(reason).
Previous chan_pjsip behavior:
Before this patch chan_pjsip would always pass the incoming reason value
up as the REDIRECTING(reason). For an outgoing reason value, chan_pjsip
would send the reason value as passed down.
With this patch:
Both channel drivers match incoming reason values with values documented
by REDIRECTING(reason) and values documented by RFC5806 regardless of
whether they are quoted or not. RFC5806 values are mapped to the
equivalent REDIRECTING(reason) documented value and is set in
REDIRECTING(reason). e.g., an incoming RFC5806 'unconditional' value or a
quoted string version ('"unconditional"') is converted to
REDIRECTING(reason)'s 'cfu' value. The user's dialplan only needs to deal
with 'cfu' instead of any of the aliases.
The incoming 480 response reason text supported by chan_sip checks for
known reason values and if not matched then puts quotes around the reason
string and assigns that to REDIRECTING(reason).
Both channel drivers send outgoing known REDIRECTING(reason) values as the
unquoted RFC5806 equivalent. User custom values are either sent as is or
with added quotes if SIP doesn't allow a character within the value as
part of a RFC3261 Section 25.1 token. Note that there are still
limitations on what characters can be put in a custom user value. e.g.,
embedding quotes in the middle of the reason string is silly and just
going to cause you grief.
* Setting a REDIRECTING(reason) value now recognizes RFC5806 aliases.
e.g., Setting REDIRECTING(reason) to 'unconditional' is converted to the
'cfu' value.
* Added missing malloc() NULL return check in res_pjsip_diversion.c
set_redirecting_reason().
* Fixed potential read from a stale pointer in res_pjsip_diversion.c
add_diversion_header(). The reason string needed to be copied into the
tdata memory pool to ensure that the string would always be available.
Otherwise, if the reason string returned by reason_code_to_str() was a
user's reason string then the string could be freed later by another
thread.
Change-Id: Ifba83d23a195a9f64d55b9c681d2e62476b68a87
chan_sip could not handle AST_T38_TERMINATED frames being sent to it when
the channel left the bridge. The action resulted in overlapping outgoing
reINVITEs. The testsuite tests/fax/sip/directmedia_reinvite_t38 was not
happy.
* Force T.38 to be remembered as locally bridged. Now when the channel
leaves the native RTP bridge after T.38, the channel remembers that it has
already reINVITEed the media back to Asterisk. It just needs to terminate
T.38 when the AST_T38_TERMINATED arrives.
* Prevent redundant AST_T38_TERMINATED from causing problems. Redundant
AST_T38_TERMINATED frames could cause overlapping outgoing reINVITEs if
they happen before the T.38 state changes to disabled. Now the T.38 state
is set to disabled before the reINVITE is sent.
ASTERISK-25582 #close
Change-Id: I53f5c6ce7d90b3f322a942af1a9bcab6d967b7ce
Use the correct comparison function since we only care if the address
without the port is the same.
Change-Id: Ibf6c485f843a1be6dee58a47b33d81a7a8cbe3b0
Setting the sip.conf timert1 value to a value higher than 1245 can cause
an integer overflow and result in large retransmit timeout times. These
large timeout times hold system file descriptors hostage and can cause the
system to run out of file descriptors.
NOTE: The default sip.conf timert1 value is 500 which does not expose the
vulnerability.
* The overflow is now detected and the previous timeout time is
calculated.
ASTERISK-25397 #close
Reported by: Alexander Traud
Change-Id: Ia7231f2f415af1cbf90b923e001b9219cff46290
When I ask asterisk to send a SIP NOTIFY message to a sip peer using either a)
AMI action: SIPnotify or b) cli command: sip notify <cmd> <peer>, I expect
asterisk to include the same value for its own ip in both cases a) and b),
but it seems a) produces a contact header like Contact:
<sip:asterisk@192.168.1.227:8060> whereas b) produces a contact header like
<sip:asterisk@127.0.0.1:8060>. 0.0.0.0:8060 is my udpbindaddr in sip.conf
My guess is that manager_sipnotify should call
ast_sip_ouraddrfor(&p->sa, &p->ourip, p) the same way sip_cli_notify does,
because after applying this patch, both cases a) and b) produce
the contact header that I expect: <sip:asterisk@192.168.1.227:8060>
Reported by: Stefan Engström
Tested by: Stefan Engström
Change-Id: I86af5e209db64aab82c25417de6c768fb645f476
sip_sipredirect uses sscanf to copy up to 256 characters to a stacked buffer
of 256 characters. This patch reduces the copy to 255 characters to leave
room for the string null terminator.
ASTERISK-25722 #close
Change-Id: Id6c3a629a609e94153287512c59aa1923e8a03ab
websocket_write_timeout was not being set to its default value
during sip config reload, which meant that prior to this commit,
1) the default value of 100 was not used, unless an invalid value
(or 1) was specified in sip.conf for websocket_write_timeout, and
2) if the websocket_write_timeout directive was removed from sip.conf
without a full restart of asterisk, then the previous value would
continue to be used indefinitely.
This essentially lead to a 0ms write timeout (the first write attempt
in ast_careful_fwrite must have succeeded) in websocket write requests
from chan_sip, unless websocket_write_timeout was explicitely set in sip.conf.
Changes to websocket_write_timeout still only apply to new websocket
sessions, after the sip reload -- timeouts on existing sessions are
not adjusted during sip reload.
Change-Id: Ibed3816ed29cc354af6564c5ab3e75eab72cb953
Per the documentation the WebSocket support in chan_sip is
supposed to be enabled by default but is not. This change
corrects that.
Change-Id: Icb02bbcad47b11a795c14ce20a9bf29649a54423
Adds the TCP Keep Alive option to TCP and TLS server sockets. Previously
this option was only being set on session sockets.
http://www.tldp.org/HOWTO/html_single/TCP-Keepalive-HOWTO/
According to the link above, the SO_KEEPALIVE option is useful for knowing
when a TCP connected endpoint has severed communication without indicating
it or has become unreachable for some reason. Without this patch, keep
alive is not set on the socket listening for incoming TCP sessions and
in Komatsu's report this resulted in the thread listening for TCP becoming
stuck in a waiting state.
ASTERISK-25364 #close
Reported by: Hiroaki Komatsu
Change-Id: I7ed7bcfa982b367dc64b4b73fbd962da49b9af36
Asterisk may crash when calling ast_channel_get_t38_state(c)
on a locked channel which is being hung up.
ASTERISK-25609 #close
Change-Id: Ifaa707c04b865a290ffab719bd2e5c48ff667c7b
The current logic for ICE negotiation starts it
when receiving an SDP with ICE candidates. This is
incorrect as ICE negotiation can only start when each
call party have at least one pair of local and remote
candidate. Starting ICE negotiation early would result
in negotiation failure and ultimately no audio.
This change makes it so ICE negotiation is only started
when a response with SDP is received or when a response
with SDP is sent.
ASTERISK-24146
Change-Id: I55a632bde9e9827871b09141d82747e08379a8ca
A crash happens sometimes when performing a CLI "sip reload". The bogus
peer gets refreshed while it is in use by a new call which can cause the
crash.
* Protected the global bogus peer object with an ao2 global object
container.
ASTERISK-25610 #close
Change-Id: I5b528c742195681abcf713c6e1011ea65354eeed
chan_sip.c:
* Initialize mwi subscription scheduler ids earlier because of ASTOBJ to
ao2 conversion.
* Initialize register scheduler ids earlier because of ASTOBJ to ao2
conversion.
chan_skinny.c:
* Fix more scheduler usage for the valid 0 id value.
ASTERISK-25476
Change-Id: If9f0e5d99638b2f9d102d1ebc9c5a14b2d706e95
channels/chan_iax2.c:
* Initialize struct chan_iax2_pvt scheduler ids earlier because of
iax2_destroy_helper().
channels/chan_sip.c:
channels/sip/config_parser.c:
* Fix initialization of scheduler id struct members. Some off nominal
paths had 0 as a scheduler id to be destroyed when it was never started.
chan_skinny.c:
* Fix some scheduler id comparisons that excluded the valid 0 id.
channel.c:
* Fix channel initialization of the video stream scheduler id.
pbx_dundi.c:
* Fix channel initialization of the packet retransmission scheduler id.
ASTERISK-25476
Change-Id: I07a3449f728f671d326a22fcbd071f150ba2e8c8
When a channel is in a direct media bridge, a re-INVITE may arrive that forces
Asterisk to re-negotiate the media to a T.38 fax. When this occurs, the bridge
must change its technology to a simple bridge, and re-INVITE the media back
to Asterisk.
Generally, this logic mostly already exists in Asterisk. However, prior to this
patch, there were a few bugs:
(1) The T.38 framehook currently prevents a channel capable of T.38 faxes from
ever entering into a direct media bridge. This applies even when the only
media being passed over the channel is audio. This patch fixes this bug
by having the framehook specify that it defers caring about any frame type.
This allows the channels to enter into a direct media bridge, which will
be broken when a re-INVITE is received.
(2) When a re-INVITE is received, nothing instructed the bridging layer to
re-inspect the allowed bridging technology. This now occurs when either
a re-INVITE is received from a peer, or when a response is received from
the far end (that is, when the T.38 state changes to either
T38_PEER_REINVITE or T38_LOCAL_REINVITE).
(3) chan_pjsip needs to do a small amount of work to prevent a direct media
bridge from being chosen when a T.38 session is in progress. When a T.38
session supplement has a t38 datastore - which is added when we detect
we should start thinking about T.38 on a channel - we now refuse a native
RTP bridge.
(4) When a BYE request is received, we don't terminate the T.38 session. If
the other side of a T.38 fax survives the hangup (due to the 'g' flag
in Dial, for example), we don't currently re-INVITE the media on the
other channel back to audio. This patch now has res_pjsip_t38 intercept
BYE requests and inform the far side that the T.38 session is terminated.
This naturally causes the correct re-INVITEs to be sent.
ASTERISK-25582
Change-Id: Iabd6aa578e633d16e6b9f342091264e4324a79eb
When ASTERISK-25449 was closed, a number of scheduler issues mentioned in
the comments were missed. These have since beed raised in ASTERISK-25476
and elsewhere.
This patch attempts to collect all of the scheduler issues discovered so
far and address them sensibly.
ASTERISK-25476 #close
Change-Id: I87a77d581e2e0d91d33b4b2fbff80f64a566d05b
This patch adds a new setting "websockets_enabled" to sip.conf.
Setting this to false allows chan_sip to be used without causing
conflicts with res_pjsip_transport_websocket.
ASTERISK-24106 #close
Reported by: Andrew Nagy
Change-Id: I04fe8c4f2d57b2d7375e0e25826c91a72e93bea7
Since version 13, Asterisk sent all allowed codecs as callee, even when the
caller did not request/support them. In case of dynamic RTP payloads, this led
to the same ID for different codecs, which is not allowed by SIP/SDP. Now, the
intersection between the requested and the supported codecs is send again.
ASTERISK-24543 #close
Change-Id: Ie90cb8bf893b0895f8d505e77343de3ba152a287
Fixed 1 issue in each of the affected files.
ASTERISK-25494 #close
Reported-by: George Joseph
Tested-by: George Joseph
Change-Id: I818f149cd66a93b062df421e1c73c7942f5a4a77
With Asterisk 13, the structures ast_format and ast_codec changed. Because of
that, the paketization timing (framing) of the RTP channel moved away from the
formats/codecs. In the course of that change, the ptime of the callee was not
honored anymore, when the optional autoframing was enabled.
ASTERISK-25484 #close
Change-Id: Ic600ccaa125e705922f89c72212c698215d239b4
To quote Olle:
"When issuing a hangup due to RTP timeouts the cause code is not set. I have
selected 44 based on Cisco's implementation..."
ASTERISK-25135 #close
Reported by: Olle Johansson
patches:
rtp-timeout-cause-1.8.diff uploaded by Olle Johansson (License 5267)
Change-Id: Ia62100c55077d77901caee0bcae299f8dc7375fc
If a Via header containes an IPv6 address and a port number is ommitted,
as it is the standard port, we now leave the port empty and to not set it
to the value after the first colon of the IPv6 address.
ASTERISK-25443 #close
Change-Id: Ie3c2f05471cd006bf04ed15598589c09577b1e70
Apparently some endpoints attempt to send a reINVITE before completing the
initial INVITE transaction. In this case PJSIP responds appropriately to
the reINVITE with a 491 INVITE request pending. Unfortunately chan_pjsip
is using the initial INVITE transaction state to determine if an INVITE is
the initial INVITE or a reINVITE. Since the initial INVITE transaction
has not been confirmed yet chan_pjsip thinks the reINVITE is an initial
INVITE and starts another PBX thread on the channel. The extra PBX thread
ensures that hilarity ensues.
* Fix checks for a reINVITE on incoming requests to look for the presence
of a to-tag instead of the initial INVITE transaction state.
* Made caller_id_incoming_request() determine what to do if there is a
channel on the session or not. After a channel is created it is too late
to just store the new party id on the session because the session's party
id has already been copied to the channel's caller id.
ASTERISK-25404 #close
Reported by: Chet Stevens
Change-Id: Ie78201c304a2b13226f3a4ce59908beecc2c68be
When 5c713fdf18 was merged, it allowed for scheduled items to have an ID of
'0' returned. While this was valid per the documentation for the API, it was
apparently never returned previously. As a result, several users of the
scheduler API viewed the result as being invalid, causing them to reschedule
already scheduled items or otherwise fail in interesting ways.
This patch corrects the users such that they view '0' as valid, and a returned
ID of -1 as being invalid.
Note that the failing HEP RTCP tests now pass with this patch. These tests
failed due to a duplicate scheduling of the RTCP transmissions.
ASTERISK-25449 #close
Change-Id: I019a9aa8b6997584f66876331675981ac9e07e39
Some systems require the REFER packet to include a Referred-By header.
If the channel variable SIPREFERREDBYHDR is set, it passes that value as the
Referred-By header value. Otherwise, it adds the current dialog’s local info.
Reported by: Dan Cropp
Tested by: Dan Cropp
Change-Id: I3d17912ce548667edf53cb549e88a25475eda245
The CALLERID(num) and CALLERID(name) and other info are placed into the
`char from[256]` in initreqprep. If the name was too long, the addr-spec
and params wouldn't fit.
Code is moved around so the addr-spec with params is placed there first,
and then fitting in as much of the display-name as possible.
ASTERISK-25396 #close
Change-Id: I33632baf024f01b6a00f8c7f35c91e5f68c40260
Although unlikely, if the tech private is returned as
a NULL, chan_pjsip_get_rtp_peer() would crash.
ASTERISK-25323
Change-Id: Ie231369bfa7da926fb2b9fdaac228261a3152e6a
Change validation on reload module because now used the cli function for
reload. The sip_reload() function never fail and ever return NULL for this
reason on reload() now use the call the sip_reload() and return
AST_MODULE_LOAD_SUCCESS.
This problem is dectected on reload by PUT method on ARI, getting always
404 http code when the module is reloaded.
ASTERISK-25325 #close
Reporte by: Rodrigo Ramírez Norambuena
Change-Id: I41215877fb2cfc589e0d4d464000cf6825f4d7fb
This patch adds a new option to the CHANNEL function that allows for the
extraction of the SIP call-id. It is used in conjunction with the 'pjsip'
option, and will return the Call-ID of the INVITE request that established
the PJSIP channel.
ASTERISK-25352
Change-Id: I278d1f8bcfe3a53c5aa1dadebc14e92b0abd476a
In chan_pjsip_new, if allocation of the pvt
structure fails, ast_hangup is called. But
it was written to assume pvt was valid, and
this change corrects that.
ASTERISK-25323
Reported by: Scott Griepentrog
Change-Id: I5f47860fe9cee4cd56abd3f79b108678ab72cc87
The call pickup implementation in chan_sip currently sets the channel
hangup cause to "normal clearing" if call pickup is successfully
performed. This action overwrites the "answered elsewhere" hangup cause
set by the call pickup code and can result in the SIP device in
question showing a missed call when it should not.
This change sets the hangup cause to "normal clearing" as a
default initially but allows the call pickup to change it as
needed.
ASTERISK-25346 #close
Change-Id: I00ac2c269cee9e29586ee2c65e83c70e52a02cff
In chan_sip, after handling an incoming invite a security event is raised
describing authorization (success, failure, etc...). However, it was doing
a lookup of the peer by extension. This is fine for register messages, but
in the case of an invite it may search and find the wrong peer, or a non
existent one (for instance, in the case of call pickup). Also, if the peers
are configured through realtime this may cause an unnecessary database lookup
when caching is enabled.
This patch makes it so that sip_report_security_event searches by IP address
when looking for a peer instead of by extension after an invite is processed.
ASTERISK-25320 #close
Change-Id: I9b3f11549efb475b6561c64f0e6da1a481d98bc4
Pressing DTMF digits on a phone to go out on a DAHDI channel can result in
the digit not being recognized or even heard by the peer.
Phone -> Asterisk -> DAHDI/channel
Turns out the DAHDI behavior with DTMF generation (and any other generated
tones) is exposed by the "buffers=" setting in chan_dahdi.conf. When
Asterisk requests to start sending DTMF then DAHDI waits until its write
buffer is empty before generating any samples for the DTMF tones. When
Asterisk subsequently requests DAHDI to stop sending DTMF then DAHDI
immediately stops generating the DTMF samples. As a result, the more
samples there are in the DAHDI write buffer the shorter the time DTMF
actually gets sent on the wire. If there are more samples in the write
buffer than the time DTMF is supposed to be sent then no DTMF gets sent on
the wire. With the "buffers=12,half" setting and each buffer representing
20 ms of samples then the DAHDI write buffer is going to contain around
120 ms of samples. For DTMF to be recognized by the peer the actual sent
DTMF duration needs to be a minimum of 40 ms. Therefore, the intended
duration needs to be a minimum of 160 ms for the peer to receive the
minimum DTMF digit duration to recognize it.
A simple and effective solution to work around the DAHDI behavior is for
Asterisk to flush the DAHDI write buffer when sending DTMF so the full
duration of DTMF is actually sent on the wire. When someone is going to
send DTMF they are not likely to be talking before sending the tones so
the flushed write samples are expected to just contain silence.
* Made dahdi_digit_begin() flush the DAHDI write buffer after requesting
to send a DTMF digit.
ASTERISK-25315 #close
Reported by John Hardin
Change-Id: Ib56262c708cb7858082156bfc70ebd0a220efa6a
There is a window of opportunity for DTMF to not go out if an audio frame
is in the process of being written to DAHDI while another thread starts
sending DTMF. The thread sending the audio frame could be past the
currently dialing check before being preempted by another thread starting
a DTMF generation request. When the thread sending the audio frame
resumes it will then cause DAHDI to stop the DTMF tone generation. The
result is no DTMF goes out.
* Made dahdi_write() lock the private struct before writing to the DAHDI
file descriptor.
ASTERISK-25315
Reported by John Hardin
Change-Id: Ib4e0264cf63305ed5da701188447668e72ec9abb
iLBC 20 was advertised in a SIP/SDP negotiation. However, only iLBC 30 is
supported. Removes "a=fmtp:x mode=y" from SDP. Because of RFC 3952 section 5,
only iLBC 30 is negotiated now.
ASTERISK-25309 #close
Change-Id: I92d724600a183eec3114da0ac607b994b1a793da
We have seen a rash of test failures on a 32-bit build agent. Commit
48698a5e21 solved an obvious problem where
we were not encoding a 64-bit value correctly over the wire. This
commit, however, did not solve the test failures.
In the failing tests, ARI is attempting to send a 537 byte text frame
over a websocket. When sending a frame this small, 16 bits are all that
is required in order to encode the payload length on the websocket
frame. However, ast_websocket_write() thinks that the payload length is
greater than 65535 and therefore writes out a 64 bit payload length.
Inspecting this payload length, the lower 32 bits are exactly what we
would expect it to be, 537 in hex. The upper 32 bits, are junk values
that are not expected to be there.
In the failure, we are passing the result of strlen() to a function that
expects a uint64_t parameter to be passed in. strlen() returns a size_t,
which on this 32-bit machine is 32 bits wide. Normally, passing a 32-bit
unsigned value to somewhere where a 64-bit unsigned value is expected
would cause no problems. In fact, in manual runs of failing tests, this
works just fine. However, ast_websocket_write() uses the Asterisk
optional API, which means that rather than a simple function call, there
are a series of macros that are used for its declaration and
implementation. These macros may be causing some sort of error to occur
when converting from a 32 bit quantity to a 64 bit quantity.
This commit changes the logic by making existing ast_websocket_write()
calls use ast_websocket_write_string() instead. Within
ast_websocket_write_string(), the 64-bit converted strlen is saved in a
local variable, and that variable is passed to ast_websocket_write()
instead.
Note that this commit message is full of speculation rather than
certainty. This is because the observed test failures, while always
present in automated test runs, never occur when tests are manually
attempted on the same test agent. The idea behind this commit is to fix
a theoretical issue by performing changes that should, at the least,
cause no harm. If it turns out that this change does not fix the failing
tests, then this commit should be reverted.
Change-Id: I4458dd87d785ca322b89c152b223a540a3d23e67
This change adds support for the 'rtp_timeout' and 'rtp_timeout_hold'
endpoint options. These allow the channel to be hung up if RTP
is not received from the remote endpoint for a specified number of
seconds.
ASTERISK-25259 #close
Change-Id: I3f39daaa7da2596b5022737b77799d16204175b9
Receipt of an RTP packet currently causes the formats on an PJSIP channel to
change to the format of the RTP packet. In some off-nominal cases it's possible
for this to be a format that has not been configured or negotiated. This change
makes it so only formats explicitly configured on the endpoint are allowed.
ASTERISK-25258 #close
Change-Id: If93d641fb6418a285928839300d7854cab8c1020
In channels/sig_pri.h, struct sig_pri_span, the field
force_restart_unavailable_chans is only defined if
#if defined(HAVE_PRI_MCID) is true.
All other occurences of force_restart_unavailable_chans are outside of the
#if defined(HAVE_PRI_MCID)
endif
scope.
ASTERISK-25257 #close
Reported by: Patric Marschall
Change-Id: I071de89cc2cd0d85927a013036e235851f672549
This patch updates a variety of Makefiles in Asterisk's build system to
remove .gcda and .gcno files when 'make clean' is executed. These files
are generated when '--enable-coverage' is passed to the Asterisk
configure script.
Change-Id: Ib70b41eea2ee2908885bff02e80faf9f40c84602
When handle_invite_replaces() was called, and either ast_bridge_impart()
failed or there was no bridge (because the channel we're picking up was
still ringing), chan_sip would leak a channel.
Thanks Matt and Corey for checking the bridge path.
ASTERISK-25226 #close
Change-Id: Ie736bb182170a73eef5bcef0ab0376f645c260c8
On reload, previously allowed codecs were not removed. Therefore, it was not
possible to remove codecs while Asterisk was running. Furthermore, newly added
codecs got appended behind the previous codecs. Therefore, it was not possible
to add a codec with a priority of #1. This change removes the old capabilities
before the current ones are added.
ASTERISK-25182 #close
Reported by: Alexander Traud
patches:
asterisk_13_allow_codec_reload.patch uploaded by Alexander Traud (License 6520)
Change-Id: I62a06bcf15e08e8c54a35612195f97179ebe5802
Due to the use of stasis_unsubscribe_and_join in the peer destructor
it is possible for a deadlock to occur when an event callback is
occurring at the same time.
This happens because the peer may be destroyed while holding the
peers container lock. If this occurs the event callback will never
be able to acquire the container lock and the unsubscribe will
never complete.
This change makes it so the peers that have been removed from the
peers container are not destroyed with the container lock held.
ASTERISK-25163 #close
Change-Id: Ic6bf1d9da4310142a4d196c45ddefb99317d9a33
If a client sends and INVITE which is 401 rejected, then subsequently
sends a new INVITE with the auth info and uses a different fromtag
from the first INVITE, Asterisk will accept the new INVITE as part of
the original dialog - match_req_to_dialog() specifically ignores the
fromtag. However it does not update the stored dialog with the new
fromtag.
This results in Asterisk being unable to match future packets that are
part of this dialog (such as the ACK to the OK or the OK to the BYE),
and the call is dropped.
This problem was originally found when using an NEC-i SV8100-GE (NEC SIP
Card).
* After a successful match of a packet to the dialog, if the packet is
not a SIP_RESPONSE, authentication is present and the fromtags are
different, the stored fromtag is updated with the one from the recent
INVITE.
ASTERISK-25154 #close
Reported by: Damian Ivereigh
Tested by: Damian Ivereigh
Change-Id: I5c16cf3b409e5ef9f2b2fe974b6bd2a45a6aa17e
Prior to this patch, chan_pjsip was failing to pass the endpoint's
context and the desired extension to the ast_channel_alloc_* routine.
This caused a new channel snapshot to be issued without a context and
extension, which can cause some reporting issues for users of AMI, CEL,
and other APIs. The channel driver would later set the context and
extension on the channel such that the channel would start in the
correct location in the dialplan, but the information reported in the
initial event would be incorrect.
This patch modifies the channel driver such that it now passes the
context and extension directly into the allocation routine. This
provides the information in the new channel snapshot published over
Stasis.
ASTERISK-25156 #close
Reported by: cloos
Change-Id: Ic6f8542836e596db8f662071d118e8f934fdf25e
channels/chan_iax.c: Prevent the deadlock between iax2_hangup and send_lagrq/
send_ping. This deadlock happens because the scheduled task send_lagrq(or
send_ping) starts execution after the call hangup procedure starts but before
it deletes the tasks in the scheduler.
The solution is to delete scheduled lagrq (and ping) task asynchronously
(i.e. schedule AST_SCHED_DEL for these tasks); By this, AST_SCHED_DEL will
be called in a new context (doesn't have callno locked).
This commit also cleans up the procedure of sending LAGRQ and PING.
main/sched.c: Do not assert when deleting non existant entry from scheduler.
This assert seems to be the reason for a lot of awkward code to avoid it.
ASTERISK-24983 #close
Reported by: Y Ateya
Change-Id: I03bec1fc8faacb89630269e935fa667c6d6c080c
Although ast_context_find, ast_context_find_or_create and
ast_context_destroy perform locking of the contexts table,
any context pointer can become invalid at any time that the
contexts table is unlocked. This change adds locking around
all complete operations involving these functions.
Places where ast_context_find was followed by ast_context_destroy
have been replaced with calls ast_context_destroy_by_name.
ASTERISK-25094 #close
Reported by: Corey Farrell
Change-Id: I1866b6787730c9c4f3f836b6133ffe9c820734fa
Many uses of stasis_unsubscribe in modules can be reached through unload.
These have been switched to stasis_unsubscribe_and_join.
Some subscription callbacks do nothing, for these I've created a noop
callback function in stasis.c. This is used by some modules that monitor
MWI topics in order to enable cache, since the callback does not become
invalid after dlclose it is safe to use stasis_unsubscribe on these, even
during module unload.
ASTERISK-25121 #close
Change-Id: Ifc2549fbd8eef7d703c222978e8f452e2972189c
Add missing return -1 when no endpoint name is specified.
ASTERISK-25086 #close
Reported by: snuffy
Change-Id: I9de76c2935a1f4e3f0cffe97a670106f5605e89e
If an ISDN call is hungup by both sides at the same time a crash could
happen.
* Added missing NULL checks for the owner channel after calling
pri_queue_pvt_cause_data() in two places. Code after those calls need to
check the owner channel pointer for NULL before use because
pri_queue_pvt_cause_data() needs to do deadlock avoidance to lock the
owner and the owner may get hung up.
ASTERISK-21893 #close
Reported by: Alexandr Gordeev
Change-Id: Ica3e266ebc7a894b41d762326f08653e1904bb9a
A few cases exist where headers of optional_api provders are included but
not needed. This causes unneeded calls to ast_optional_api_use.
* Don't include optional_api.h from sip_api.h.
* Move 'struct ast_channel_monitor' to channel.h.
* Don't include monitor.h from chan_sip.c, channel.c or features.c.
The move of struct ast_channel_monitor is needed since channel.c depends on
it. This has no effect on users of monitor.h since channel.h is included
from monitor.h.
ASTERISK-25051 #close
Reported by: Corey Farrell
Change-Id: I53ea65a9fc9693c89f8bcfd6120649bfcfbc3478
Some telco switches occasionally ignore ISDN RESTART requests. The fix
for ASTERISK-19608 added an escape clause for B channels in the restarting
state if the telco ignores a RESTART request. If the telco fails to
acknowledge the RESTART then Asterisk will assume the telco acknowledged
the RESTART on the second call attempt requesting the B channel by the
telco. The escape clause is good for dealing with RESTART requests in
general but it does cause the next call for the restarting B channel to be
rejected if the telco insists the call must go on that B channel.
chan_dahdi doesn't really need to issue a RESTART request in response to
receiving a cause 44 (Requested channel not available) code. Sending the
RESTART in such a situation is not required (nor prohibited) by the
standards. I think chan_dahdi does this for historical reasons to deal
with buggy peers to get channels unstuck in a similar fashion as the
chan_dahdi.conf resetinterval option.
* Add the chan_dahdi.conf force_restart_unavailable_chans compatability
option that when disabled will prevent chan_dahdi from trying to RESTART
the channel in response to a cause 44 code.
ASTERISK-25034 #close
Reported by: Richard Mudgett
Change-Id: Ib8b17a438799920f4a2038826ff99a1884042f65
A typo in commit f8e21a1adf resulted in a compilation error in
chan_skinny. This patch fixes the typo.
ASTERISK-24917
Change-Id: Id7f4ad1fe948eb2408622e80c27936ce4516c33c
clang can warn about a so called tautological-compare, when it finds
comparisons which are logically always true, and are therefor deemed
unnecessary.
Exanple:
unsigned int x = 4;
if (x > 0) // x is always going to be bigger than 0
Enum Case:
Each enumeration is its own type. Enums are an integer type but they
do not have to be *signed*. C leaves it up to the compiler as an
implementation option what to consider the integer type of a particu-
lar enumeration is. Gcc treats an enum without negative values as
an int while clang treats this enum as an unsigned int.
rmudgett & mmichelson: cast the enum to (unsigned int) in assert.
The cast does have an effect. For gcc, which seems to treat all enums
as int, the cast to unsigned int will eliminate the possibility of
negative values being allowed. For clang, which seems to treat enums
without any negative members as unsigned int, the cast will have no
effect. If for some reason in the future a negative value is ever
added to the enum the assert will still catch the negative value.
ASTERISK-24917
Change-Id: Ief23ef68916192b9b72dabe702b543ecfeca0b62
The chan_dahdi channel driver is a very old driver. The ability for it to
support ISDN was added well after the initial analog support. Setting the
softhangup flags is a carry over from the original analog code. The
driver was not updated to call ast_queue_hangup() which will post the AMI
HangupRequest event.
* Changed sig_pri.c to call ast_queue_hangup() instead of setting the
softhangup flag when the remote party initiates a hangup.
ASTERISK-24895 #close
Reported by: Andrew Zherdin
Change-Id: I5fe2e48556507785fd8ab8e1c960683fd5d20325
With this patch, chan_pjsip/res_pjsip now sets the native formats to the
codecs negotiated by a call.
* The changes in chan_pjsip.c and res_pjsip_sdp_rtp.c set the native
formats to include all the negotiated audio codecs instead of only the
initial preferred audio codec and later the currently received audio
codec.
* The audio frame handling in channel.c:ast_read() is more streamlined and
will automatically adjust to changes in received frame formats. The new
policy is to remove translation and pass the new frame format to the
receiver except if the translation was to a signed linear format. A more
long winded version is commented in ast_read() along with some caveats.
* The audio frame handling in channel.c:ast_write() is more streamlined
and will automatically adjust any needed translation to changes in the
frame formats sent. Frame formats sent can change for many reasons such
as a recording is being played back or the bridged peer changed the format
it sends. Since it is a normal expectation that sent formats can change,
the codec mismatch warning message is demoted to a debug message.
* Removed the short circuit check in
channel.c:ast_channel_make_compatible_helper(). Two party bridges need to
make channels compatible with each other. However, transfers and moving
channels among bridges can result in otherwise compatible channels having
sub-optimal translation paths if the make compatible check is short
circuited. A result of forcing the reevaluation of channel compatibility
is that the asterisk.conf:transcode_via_slin and codecs.conf:genericplc
options take effect consistently now. It is unfortunate that these two
options are enabled by default and negate some of the benefits to the
changes in channel.c:ast_read() by forcing translation through signed
linear on a two party bridge.
* Improved the softmix bridge technology to better control the translation
of frames to the bridge. All of the incoming translation is now normally
handled by ast_read() instead of splitting any translation steps between
ast_read() and the slin factory. If any frame comes in with an unexpected
format then the translation path in ast_read() is updated for the next
frame and the slin factory handles the current frame translation.
This is the final patch in a series of patches aimed at improving
translation path choices. The other patches are on the following reviews:
https://reviewboard.asterisk.org/r/4600/https://reviewboard.asterisk.org/r/4605/
ASTERISK-24841 #close
Reported by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/4609/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434671 65c4cc65-6c06-0410-ace0-fbb531ad65f3
After the "progressinband" value setting of "never" was updated to never send a
183 this separated its use from the "no" value. Since "never" was the default,
but most users probably expect "no" this patch updates the default for the
"progressinband" setting to "no."
ASTERISK-24835 #close
Reported by: Andrew Nagy
Review: https://reviewboard.asterisk.org/r/4606/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434654 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds support for automatically detecting the type of DTMF that a
PJSIP endpoint supports. When the 'dtmf_mode' endpoint option is set to 'auto',
the channel created for an endpoint will attempt to determine if RFC 4733
DTMF is supported. If so, it will use that DTMF type. If not, the DTMF type
for the channel will be set to inband.
Review: https://reviewboard.asterisk.org/r/4438
ASTERISK-24706 #close
Reported by: yaron nahum
patches:
yaron_patch_3_Feb.diff submitted by yaron nahum (License 6676)
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434637 65c4cc65-6c06-0410-ace0-fbb531ad65f3
POKE is used to check for peer availability; however, in networks with packet
loss, the current calculations may result in POKE expiration times that are too
short. This patch alters the expiration/retry time logic to take into account
the last known qualify round trip time, as opposed to always using a static
value for each peer.
Review: https://reviewboard.asterisk.org/r/4536
ASTERISK-22352 #close
Reported by: Frederic Van Espen
ASTERISK-24894 #close
Reported by: Y Ateya
patches:
poke_noanswer_duration.diff submitted by Y Ateya (License 6693)
........
Merged revisions 434564 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434565 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This fixes autological comparison warnings in the following:
* chan_skinny: letohl may return a signed or unsigned value, depending on the
macro chosen
* func_curl: Provide a specific cast to CURLoption to prevent mismatch
* cel: Fix enum comparisons where the enum can never be negative
* enum: Fix comparison of return result of dn_expand, which returns a signed
int value
* event: Fix enum comparisons where the enum can never be negative
* indications: tone_data.freq1 and freq2 are unsigned, and hence can never be
negative
* presencestate: Use the actual enum value for INVALID state
* security_events: Fix enum comparisons where the enum can never be negative
* udptl: Don't bother to check if the return value from encode_length is less
than 0, as it returns an unsigned int
* translate: Since the parameters are unsigned int, don't bother checking
to see if they are negative. The cast to unsigned int would already blow
past the matrix bounds.
* res_pjsip_exten_state: Use a temporary value to cache the return of
ast_hint_presence_state
* res_stasis_playback: Fix enum comparisons where the enum can never be
negative
* res_stasis_recording: Add an enum value for the case where the recording
operation is in error; fix enum comparisons
* resource_bridges: Use enum value as opposed to -1
* resource_channels: Use enum value as opposed to -1
Review: https://reviewboard.asterisk.org/r/4533
ASTERISK-24917
Reported by: dkdegroot
patches:
rb4533.patch submitted by dkdegroot (License 6600)
........
Merged revisions 434469 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434470 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When a channel enters the bridging system it is first made compatible with
the bridge and then the bridge technology makes the channel compatible
with the technology. For all but the DAHDI native and softmix bridge
technologies the make channel compatible with the bridge step is an
effective noop because the other technologies allow all audio formats.
For the DAHDI native bridge technology it doesn't matter because it is not
an initial bridge technology and chan_dahdi allows only one native format
per channel. For the softmix bridge technology, it is a noop at best and
harmful at worst because the wrong translation path could be setup if the
channel's native formats allow more than one audio format.
This is an intermediate patch for a series of patches aimed at improving
translation path choices.
* Removed code dealing with the unnecessary step of making the channel
compatible with the bridge.
ASTERISK-24841
Reported by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/4600/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434424 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch fixes an access to the peer callnumber that is unprotected by a
corresponding mutex. The peer->callno value can be changed by multiple threads,
and all data inside the iaxs array must be procted by a corresponding lock
of iaxsl.
The patch moves the unprotected access to a location where the mutex is
safely obtained.
Review: https://reviewboard.asterisk.org/r/4599/
ASTERISK-21211 #close
Reported by: Jaco Kroon
patches:
asterisk-11.2.1-iax2_poke-segfault.diff submitted by Jaco Kroon (License 5671)
........
Merged revisions 434291 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434292 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When udpbindaddr is set to the IPv6 bind all address of '::', Asterisk will
attempt to handle both IPv4 and IPv6 addresses, although the information will
be stored in a struct with an AF_INET6 address type. However, the current
NAT handling code won't handle the IPv4 mapped IPv6 addresses correctly.
This patch adds an additional check for the mapped address case, allowing
the NAT code to handle clients even when the address is IPv6.
Review: https://reviewboard.asterisk.org/r/4563/
ASTERISK-18032 #close
Reported by: Christoph Timm
patches:
nat_with_ipv6.diff submitted by Valentin Vidić (License 6697)
........
Merged revisions 434288 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434289 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch fixes several warnings pointed out by the clang compiler.
* chan_pjsip: Removed check for data->text, as it will always be non-NULL.
* app_minivm: Fixed evaluation of etemplate->locale, which will always
evaluate to 'true'. This patch changes the evaluation to use
ast_strlen_zero.
* app_queue:
- Fixed evaluation of qe->parent->monfmt, which always evaluates to
true. Instead, we just check to see if the dereferenced pointer
evaluates to true.
- Fixed evaluation of mem->state_interface, wrapping it with a call to
ast_strlen_zero.
* res_smdi: Wrapped search_msg->mesg_desk_term with calls to ast_strlen_zero.
Review: https://reviewboard.asterisk.org/r/4541
ASTERISK-24917
Reported by: dkdegroot
patches:
rb4541.patch submitted by dkdegroot (License 6600)
........
Merged revisions 434285 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434286 65c4cc65-6c06-0410-ace0-fbb531ad65f3
These are fixes for compilation under gcc 5.0...
chan_sip.c: In parse_request needed to make 'lim' unsigned.
inline_api.h: Needed to add a check for '__GNUC_STDC_INLINE__' to detect C99
inline semantics (same as clang).
ccss.c: In ast_cc_set_parm, needed to fix weird comparison.
dsp.c: Needed to work around a possible compiler bug. It was throwing
an array-bounds error but neither
sgriepentrog, rmudgett nor I could figure out why.
manager.c: In action_atxfer, needed to correct an array allocation.
This patch will go to 11, 13, trunk.
Review: https://reviewboard.asterisk.org/r/4581/
Reported-by: Jeffrey Ollie
Tested-by: George Joseph
ASTERISK-24932 #close
........
Merged revisions 434113 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@434114 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch fixes some invalid enum conversion warnings caught by clang. In
particular:
* chan_sip: Several functions mixed usage of the st_refresher_param
enum and st_refresher enum. This patch corrects the functions to use the
right enum.
* chan_pjsip: Fixed mixed usage of ast_sip_session_t38state and ast_t38_state.
* strings: Fixed incorrect usage of AO2 flags with strings container.
* res_stasis: Change a return enumeration to stasis_app_user_event_res.
Review: https://reviewboard.asterisk.org/r/4535
ASTERISK-24917
Reported by: dkdegroot
patches:
rb4535.patch submitted by dkdegroot (License 6600)
........
Merged revisions 433746 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@433747 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Incoming PJSIP call legs that have not been answered yet send unnecessary
"180 Ringing" or "183 Progress" messages every time a connected line
update happens. If the outgoing channel is also PJSIP then the incoming
channel will always send a "180 Ringing" or "183 Progress" message when
the outgoing channel sends the INVITE.
Consequences of these unnecessary messages:
* The caller can start hearing ringback before the far end even gets the
call.
* Many phones tend to grab the first connected line information and refuse
to update the display if it changes. The first information is not likely
to be correct if the call goes to an endpoint not under the control of the
first Asterisk box.
When connected line first went into Asterisk in v1.8, chan_sip received an
undocumented option "rpid_immediate" that defaults to disabled. When
enabled, the option immediately passes connected line update information
to the caller in "180 Ringing" or "183 Progress" messages as described
above.
* Added "rpid_immediate" option to prevent unnecessary "180 Ringing" or
"183 Progress" messages. The default is "no" to disable sending the
unnecessary messages.
ASTERISK-24781 #close
Reported by: Richard Mudgett
Review: https://reviewboard.asterisk.org/r/4473/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@433338 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The res_pjsip modules were manually checking both name and number
presentation values when there is a function that determines the combined
presentation for a party ID struct. The function takes into account if
the name or number components are valid while the manual code rarely
checked if the data was even valid.
* Made use ast_party_id_presentation() rather than manually checking party
ID presentation values.
* Ensure that set_id_from_pai() and set_id_from_rpid() will not return
presentation values other than what is pulled out of the SIP headers. It
is best if the code doesn't assume that AST_PRES_ALLOWED and
AST_PRES_USER_NUMBER_UNSCREENED are zero.
* Fixed copy paste error in add_privacy_params() dealing with RPID
privacy.
* Pulled the id->number.valid test from add_privacy_header() and
add_privacy_params() up into the parent function add_id_headers() to skip
adding PAI/RPID headers earlier.
* Made update_connected_line_information() not send out connected line
updates if the connected line number is invalid. Lower level code would
not add the party ID information and thus the sent message would be
unnecessary.
* Eliminated RAII_VAR usage in send_direct_media_request().
Review: https://reviewboard.asterisk.org/r/4472/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@432892 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The distinctive ring feature interferes with detecting Caller ID and
appears to have been broken for years. What happens is if you have a
ring-ring cadence as used in the UK you get too many DAHDI events for the
distinctive ring pattern array and Caller ID detection is aborted. I
think when Zapata/DAHDI added the ring begin event it broke distinctive
ring. More events happen than before and the code does no filtering of
which event times are recorded in the pattern array.
* Made distinctive ring only record the ringt count when the ring ends
instead of on just any DAHDI event. Distinctive ring can be ring,
ring-ring, ring-ring-ring, or different ring durations for the up to three
rings.
* Fixed the distinctive ring detection enable (chan_dahdi.conf option
usedistinctiveringdetection) to be per port instead of somewhat per port
and somewhat global. This has been broken since v1.8.
* Fixed using the default distinctive ring context when the detected
pattern does not match any configured dringX patterns. The default
context did not get set when the previous call was a matched distinctive
ring pattern and the current call is not matched. This has been broken
since v1.8.
* Made distinctive ring have no effect on Caller ID detection when it is
disabled. Caller ID detection just monitors for 10 seconds before giving
up.
* Fixed leak of struct callerid_state memory when a polarity reversal
during Caller ID detection causes the incoming call to be aborted.
DAHDI-1143
AST-1545
ASTERISK-24825 #close
Reported by: Richard Mudgett
ASTERISK-17588
Reported by: Daniel Flounders
Review: https://reviewboard.asterisk.org/r/4444/
........
Merged revisions 432530 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@432534 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When a realtime peer is built it can cause a locking inversion when the
just built peer is poked. If the CLI command "sip show channels" is
periodically executed then a deadlock can happen because of the locking
inversion.
* Push the peer poke off onto the scheduler thread to avoid the locking
inversion of the just built realtime peer.
AST-1540
ASTERISK-24838 #close
Reported by: Richard Mudgett
Review: https://reviewboard.asterisk.org/r/4454/
........
Merged revisions 432526 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@432528 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When Asterisk fails to start a PBX thread for a new channel - for example, when
the maxcalls setting in asterisk.conf is exceeded - we currently send a final
response, and then attempt to send a BYE request to the UA. Since that's all
sorts of wrong, this patch fixes that by setting sipalreadygone on the sip_pvt
such that we don't get stuck sending BYE requests to something that does not
want it.
Note that this patch is a slight modification of the one on ASTERISK-15434.
For clarity, it explicitly calls sipalreadygone with the calls to transmit a
final response.
ASTERISK-21845
ASTERISK-15434 #close
Reported by: Makoto Dei
Tested by: Matt Jordan
patches:
sip-pbxstart-failed.patch uploaded by Makoto Dei (License 5027)
........
Merged revisions 432320 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@432321 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When we receive an SDP as part of an offer/answer for a peer/friend has been
configured to require encryption, and that SDP offer/answer failed to provide
acceptable crypto attributes, we currently issue a WARNING that uses the phrase
"we" and "requested". In this case, both of those terms are ambiguous - the
user will probably think "we" is Asterisk (it most likely isn't) and it may
not be a "request", so much as an SDP that was received in some fashion.
This patch makes the WARNING messages slightly less bad and a bit more
accurate as well.
ASTERISK-23214 #close
Reported by: Rusty Newton
........
Merged revisions 432277 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@432278 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When the monitor thread is stopped, its pthread ID is set to a specific value
(AST_PTHREADT_STOP) so that later portions of the code can determine whether
or not it is safe to manipulate the thread. Unfortunately, __sip_reliable_xmit
failed to check for that value, checking instead only for AST_PTHREAD_STOP.
Passing the invalid yet very specific value to pthread_kill causes a crash.
This patch adds a check for AST_PTHREADT_STOP in __sip_reliable_xmit such that
it doesn't attempt to poke the thread if the thread has already been stopped.
ASTERISK-24800 #close
Reported by: JoshE
........
Merged revisions 432198 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@432199 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch addresses the following problems:
* ari/resource_channels: In ARI, we currently create a format capability
structure of SLIN and apply it to the new channel being created. This was
originally done when the PBX core was used to create the channel, as there
was a condition where a newly created channel could be created without any
formats. Unfortunately, now that the Dial API is being used, this has two
drawbacks:
(a) SLIN, while it will ensure audio will flows, can cause a lot of
needless transcodings to occur, particularly when a Local channel is
created to the dialplan. When no format capabilities are available, the
Dial API handles this better by handing all audio formats to the requsted
channels. As such, we defer to that API to provide the format
capabilities.
(b) If a channel (requester) is causing this channel to be created, we
currently don't use its format capabilities as we are passing in our own.
However, the Dial API will use the requester channel's formats if none
are passed into it, and the requester channel exists and has format
capabilities. This is the "best" scenario, as it is the most likely to
create a media path that minimizes transcoding.
Fixing this simply entails removing the providing of the format capabilities
structure to the Dial API.
* chan_pjsip: Rather than blindly picking the first format in the format
capability structure - which actually *can* be a video or text format - we
select an audio format, and only pick the first format if that fails. That
minimizes the weird scenario where we attempt to transcode between video/audio.
* res_pjsip_sdp_rtp: Applied the joint capapbilites to the format structure.
Since ast_request already limits us down to one format capability once the
format capabilities are passed along, there's no reason to squelch it here.
* channel: Fixed a comment. The reason we have to minimize our requested
format capabilities down to a single format is due to Asterisk's inability
to convey the format to be used back "up" a channel chain. Consider the
following:
PJSIP/A => L;1 <=> L;2 => PJSIP/B
g,u,a g,u,a g,u,a u
That is, we have PJSIP/A dialing a Local channel, where the Local;2 dials
PJSIP/B. PJSIP/A has native format capabilities g722,ulaw,alaw; the Local
channel has inherited those format capabilities down the line; PJSIP/B
supports only ulaw. According to these format capabilities, ulaw is
acceptable and should be selected across all the channels, and no
transcoding should occur. However, there is no way to convey this: when L;2
and PJSIP/B are put into a bridge, we will select ulaw, but that is not
conveyed to PJSIP/A and L;1. Thus, we end up with:
PJSIP/A <=> L;1 <=> L;2 <=> PJSIP/B
g g X u u
Which causes g722 to be written to PJSIP/B.
Even if we can convey the 'ulaw' choice back up the chain (which through
some severe hacking in Local channels was accomplished), such that the chain
looks like:
PJSIP/A <=> L;1 <=> L;2 <=> PJSIP/B
u u u u
We have no way to tell PJSIP/A's *channel driver* to Answer in the SDP back
with only 'ulaw'. This results in all the channel structures being set up
correctly, but PJSIP/A *still* sending g722 and causing the chain to fall
apart.
There's a lot of difficulty just in setting this up, as there are numerous
race conditions in the act of bridging, and no clean mechanism to pass the
selected format backwards down an established channel chain. As such, the
best that can be done at this point in time is clarifying the comment.
Review: https://reviewboard.asterisk.org/r/4434/
ASTERISK-24812 #close
Reported by: Matt Jordan
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@432195 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds a new feature to ARI to redirect a channel to another server,
and fixes a few bugs in PJSIP's handling of the Transfer dialplan
application/ARI redirect capability.
*New Feature*
A new operation has been added to the ARI channels resource, redirect. With
this, a channel in a Stasis application can be redirected to another endpoint
of the same underlying channel technology.
*Bug fixes*
In the process of writing this new feature, two bugs were fixed in the PJSIP
stack:
(1) The existing .transfer channel callback had the limitation that it could
only transfer channels to a SIP URI, i.e., you had to pass
'PJSIP/sip:foo@my_provider.com' to the dialplan application. While this is
still supported, it is somewhat unintuitive - particularly in a world full
of endpoints. As such, we now also support specifying the PJSIP endpoint to
transfer to.
(2) res_pjsip_multihomed was, unfortunately, trying to 'help' a 302 redirect by
updating its Contact header. Alas, that resulted in the forwarding
destination set by the dialplan application/ARI resource/whatever being
rewritten with very incorrect information. Hence, we now don't bother
updating an outgoing response if it is a 302. Since this took a looong time
to find, some additional debug statements have been added to those modules
that update the Contact headers.
Review: https://reviewboard.asterisk.org/r/4316/
ASTERISK-24015 #close
Reported by: Private Name
ASTERISK-24703 #close
Reported by: Matt Jordan
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@431717 65c4cc65-6c06-0410-ace0-fbb531ad65f3
There are three CLI commands to stop and restart Asterisk each.
1) core stop/restart now - Hangup all calls and stop or restart Asterisk.
New channels are prevented while the shutdown request is pending.
2) core stop/restart gracefully - Stop or restart Asterisk when there are
no calls remaining in the system. New channels are prevented while the
shutdown request is pending.
3) core stop/restart when convenient - Stop or restart Asterisk when there
are no calls in the system. New calls are not prevented while the
shutdown request is pending.
ARI has made stopping/restarting Asterisk more problematic. While a
shutdown request is pending it is desirable to continue to process ARI
HTTP requests for current calls. To handle the current calls while a
shutdown request is pending, a new committed to shutdown phase is needed
so ARI applications can deal with the calls until the system is fully
committed to shutdown.
* Added a new shutdown committed phase so ARI applications can deal with
calls until the final committed to shutdown phase is reached.
* Made refuse new HTTP requests when the system has reached the final
system shutdown phase. Starting anything while the system is actively
releasing resources and unloading modules is not a good thing.
* Split the bridging framework shutdown to not cleanup the global bridging
containers when shutting down in a hurry. This is similar to how other
modules prevent crashes on rapid system shutdown.
* Moved ast_begin_shutdown(), ast_cancel_shutdown(), and
ast_shutting_down(). You should not have to include channel.h just to
access these system functions.
ASTERISK-24752 #close
Reported by: Matthew Jordan
Review: https://reviewboard.asterisk.org/r/4399/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@431692 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When a SIP device that has its registration stored in RealTime unregisters,
the entry for that device is updated with blank values, i.e., "", indicating
that it is no longer registered. Unfortunately, one of those values that is
'blanked' is the device's port. If the column type for the port is not a
string datatype (the recommended type is integer), an ODBC or database error
will be thrown. MariaDB does not coerce empty strings to a valid integer value.
This patch updates the query run from chan_sip such that it replaces the port
value with a value of '0', as opposed to a blank value. This is the value that
other database backends coerce the empty string ("") to already, and the
handling of reading a RealTime registration value from a backend already
anticipates receiving a port of '0' from the backends.
ASTERISK-24772 #close
Reported by: Richard Miller
patches:
chan_sip.diff uploaded by Richard Miller (License 5685)
........
Merged revisions 431673 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@431674 65c4cc65-6c06-0410-ace0-fbb531ad65f3
RFC 3261 sections 8.1.1.8 and 12.1.1 dictate specific
scenarios when we are required to use SIPS URIs in Contact
headers. Asterisk's non-compliance with this could actually
cause calls to get dropped when communicating with clients
that are strict about checking the Contact header.
Both of the SIP stacks in Asterisk suffered from this issue.
This changeset corrects the behavior in chan_sip.
ASTERISK-24646 #close
Reported by Stephan Eisvogel
Review: https://reviewboard.asterisk.org/r/4346
........
Merged revisions 431423 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@431424 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When refreshing (with a small expiration) a registration that was sent to
chan_sip the nonce would be considered stale and reject the registration.
What was happening was that the initial registration's "dialog" still existed
in the dialogs container and upon refresh the dialog match algorithm would
choose that as the "dialog" instead of the newly created one. This occurred
because the algorithm did not check to see if the from tag matched if
authentication info was available after the 401. So, it ended up assuming
the original "dialog" was a match and stopped the search. The old "dialog"
of course had an old nonce, thus the stale nonce message.
This fix attempts to leave the original functionality alone except in the case
of a REGISTER. If a REGISTER is received if searches for an existing "dialog"
matching only on the callid. If the expires value is low enough it will reuse
dialog that is there, otherwise it will create a new one.
ASTERISK-24715 #close
Reported by: John Bigelow
Review: https://reviewboard.asterisk.org/r/4367/
........
Merged revisions 431187 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@431194 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch addresses compilation errors on OS X. It's been a while, so
there's quite a few things.
* Fixed __attribute__ decls in route.h to be portable.
* Fixed htonll and ntohll to work when they are defined as macros.
* Replaced sem_t usage with our ast_sem wrapper.
* Added ast_sem_timedwait to our ast_sem wrapper.
* Fixed some GCC 4.9 warnings using sig*set() functions.
* Fixed some format strings for portability.
* Fixed compilation issues with res_timing_kqueue (although tests still fail
on OS X).
* Fixed menuconfig /sbin/launchd detection, which disables res_timing_kqueue
on OS X).
ASTERISK-24539 #close
Reported by: George Joseph
ASTERISK-24544 #close
Reported by: George Joseph
Review: https://reviewboard.asterisk.org/r/4327/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@431092 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When the SIP registrations were migrated to using ao2 in what was then trunk,
the explicit destruction of the registrations on module reload was removed and
not replaced with an ao2 equivalent. Debugging done by Stefan Engström, the
issue reporter, on ASTERISK-24673 confirmed that the reference in the
registry_list container was being leaked.
Since the purpose of cleanup_all_regs is to prep a registration for
destruction, this function now calls an ao2_callback function callback with the
OBJ_MULTIPLE | OBJ_NODATA | OBJ_UNLINK flags used to remove the registrations.
This cleans up each registration, and also removes it from the registration
container registry_list.
Review: https://reviewboard.asterisk.org/r/4355/
ASTERISK-24640 #close
Reported by: Max Man
ASTERISK-24673 #close
Reported by: Stefan Engström
Tested by: Stefan Engström
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@430864 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Calling ast_channel_bridge_peer() cannot be done while holding any channel
locks. The reported issue hit the deadlock in chan_iax2, but an audit of
the ast_channel_bridge_peer() calls found three more locations where the
same deadlock can occur.
* Made CHANNEL(peer), res_fax, and the SNMP agent not call
ast_channel_bridge_peer() with any channel locked. For CHANNEL(peer) I
had to rework the logic to not hold the channel lock.
* Made chan_iax2 no longer call ast_channel_bridge_peer(). It was done
for legacy reasons that no longer apply.
* Removed the iax.conf forcejitterbuffer option. It is now always enabled
when the jitterbuffer option is enabled. If you put a jitter buffer on a
channel it will be on the channel.
ASTERISK-24600 #close
Reported by: Jeff Collell
Review: https://reviewboard.asterisk.org/r/4342/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@430817 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Different clients react differently to being told that a blind transfer
has failed. Some will simply send a BYE and be done with it. Others will
attempt to reinvite themselves back onto the call.
In the latter case, we were creating a new channel and then leaving it to
sit forever doing nothing. With this code change, that new channel will
not be created and the dialog with the transferring channel will be cleaned
up properly.
ASTERISK-24624 #close
Reported by Zane Conkle
Review: https://reviewboard.asterisk.org/r/4339
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@430714 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The 'pjsip_get_dest_info' function is used to determine if the signaling transport
of the dialog is secure or not. This function was added in PJSIP 2.3 and does not
exist in earlier versions.
This configure check allows Asterisk to build and run with older versions at the
loss of the 'secure' argument for the PJSIP CHANNEL dialplan function. Usage of
this argument will require upgrading to PJSIP 2.3.
ASTERISK-24665 #close
Reported by: Mark Michelson
Review: https://reviewboard.asterisk.org/r/4329/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@430546 65c4cc65-6c06-0410-ace0-fbb531ad65f3
* Made the following AMI actions use list API calls for consistency:
Agents
BridgeInfo
BridgeList
BridgeTechnologyList
ConfbridgeLIst
ConfbridgeLIstRooms
CoreShowChannels
DAHDIShowChannels
DBGet
DeviceStateList
ExtensionStateList
FAXSessions
Hangup
IAXpeerlist
IAXpeers
IAXregistry
MeetmeList
MeetmeListRooms
MWIGet
ParkedCalls
Parkinglots
PJSIPShowEndpoint
PJSIPShowEndpoints
PJSIPShowRegistrationsInbound
PJSIPShowRegistrationsOutbound
PJSIPShowResourceLists
PJSIPShowSubscriptionsInbound
PJSIPShowSubscriptionsOutbound
PresenceStateList
PRIShowSpans
QueueStatus
QueueSummary
ShowDialPlan
SIPpeers
SIPpeerstatus
SIPshowregistry
SKINNYdevices
SKINNYlines
Status
VoicemailUsersList
* Incremented the AMI version to 2.7.0.
* Changed astman_send_listack() to not use the listflag parameter and
always set the value to "Start" so the start capitalization is consistent.
i.e., The FAXSessions used "Start" while the rest of the system used
"start". The corresponding complete event always used "Complete".
* Fixed ami_show_resource_lists() "PJSIPShowResourceLists" to output the
AMI ActionID for all of its list events.
* Fixed off-nominal AMI protocol error in manager_bridge_info(),
manager_parking_status_single_lot(), and
manager_parking_status_all_lots(). Use of astman_send_error() after
responding to the original AMI action request violates the action response
pattern by sending two responses.
* Fixed minor protocol error in action_getconfig() when no requested
categories are found. Each line needs to be formatted as "Header: text".
* Fixed off-nominal memory leak in manager_build_parked_call_string().
* Eliminated unnecessary use of RAII_VAR() in ami_subscription_detail().
ASTERISK-24049 #close
Reported by: Jonathan Rose
Review: https://reviewboard.asterisk.org/r/4315/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@430434 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The PJSIP_AOR dialplan function allows inspection of configured AORs including
what contacts are currently bound to them.
The PJSIP_CONTACT dialplan function allows inspection of contacts in existence.
These can include both externally added (by way of registration) or permanent
ones.
ASTERISK-24341
Reported by: xrobau
Review: https://reviewboard.asterisk.org/r/4308/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@430179 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Given the following scenario:
* Three SIP phones (A, B, C), all communicating via a proxy with Asterisk
* A call is established between A and B. B performs a SIP attended transfer of
A to C. B sets the call on hold (A is hearing MOH) and dials the extension of
C. While phone C is ringing, B transfers the call (that is, what we typically
call a 'blond transfer').
* When the transfer completes, A hears the ringing of phone C, while B is idle.
In the SIP messaging for the above scenario, a REFER request is sent to
transfer the call. When "sendrpid=yes" is set in sip.conf, Asterisk may send an
UPDATE request to phone C to update party information. This update is sent
directly to phone C, not through the intervening proxy. This has the unfortunate
side effect of providing route information, which is then set on the sip_pvt
structure for C. If someone (e.g. B) is trying to get the call back (through a
directed pickup), Asterisk will send a CANCEL request to C. However, since we
have now updated the route set, the CANCEL request will be sent directly to C
and not through the proxy. The phone ignores this CANCEL according to RFC3261
(Section 9.1).
This patch updates reqprep such that the route is not updated if an UPDATE
request is being sent while the INVITE state is INV_PROCEEDING or
INV_EARLY_MEDIA. This ensures that a subsequent CANCEL request is still sent
to the correct location.
Review: https://reviewboard.asterisk.org/r/4279
ASTERISK-24628 #close
Reported by: Karsten Wemheuer
patches:
issue.patch uploaded by Karsten Wemheuer (License 5930)
........
Merged revisions 429982 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@429983 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When the configuration section scheme of chan_dahdi.conf is used (keyword
dahdichan instead of channel) all setvar= options are completely ignored.
No variable defined this way appears in the created DAHDI channels.
* Move the clearing of setvar values to after the deferred processing of
dahdichan.
AST-1378 #close
Reported by: Guenther Kelleter
Patch by: Guenther Kelleter
........
Merged revisions 429825 from http://svn.asterisk.org/svn/asterisk/branches/11
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/13@429829 65c4cc65-6c06-0410-ace0-fbb531ad65f3
zuul
Joshua Colp
kkm
Jaco Kroon
George Joseph
Alexander Traud
Francesco Castellano
Kevin Harwell
Richard Mudgett
Mark Michelson
StefanEng86
Corey Farrell
Dade Brandon
Jonathan Rose
Filip Jenicek
Eugene Voityuk
Matt Jordan
Steve Davies
Florian Sauerteig
Debian Amtelco
Walter Doekes
Scott Griepentrog
Rodrigo Ramírez Norambuena
Patric Marschall
Damian Ivereigh
Yousf Ateya
snuffy
Diederik de Groot
David M. Lee