On a system with multiple ip addresses in the same subnet, if a
transport is bound to a specific ip address and endpoint/media_address
is set, the SIP/SDP will have the correct address in all fields but
the rtp stream MAY still originate from one of the other ip addresses,
most probably the "primary" ip address. This happens because
res_pjsip_sdp_rtp/create_rtp always calls ast_instance_new with
the "all" ip address (0.0.0.0 or ::).
The new option causes res_pjsip_sdp_rtp/create_rtp to call
ast_rtp_instance_new with the endpoint's media_address (if specified)
instead of the "all" address. This causes the packets to originate from
the specified address.
ASTERISK-25632
ASTERISK-25637
Reported-by: Olivier Krief
Reported-by: Dan Journo
Change-Id: I3dfaa079e54ba7fb7c4fd1f5f7bd9509bbf8bd88
The menuselect conflict between app_voicemail and res_mwi_external
makes it hard to package 1 version of Asterisk. There no actual
build dependencies between the 2 so moving this check to runtime
seems like a better solution.
The ast_vm_register and ast_vm_greeter_register functions in app.c
were modified to return AST_MODULE_LOAD_DECLINE instead of -1 if there
is already a voicemail module registered. The modules' load_module
functions were then modified to return DECLINE instead of -1 to the
loader. Since -1 is interpreted by the loader as AST_MODULE_LOAD_FAILURE,
the modules were incorrectly causing Asterisk to stop so this needed
to be cleaned up anyway.
Now you can build both and use modules.conf to decide which voicemail
implementation to load.
The default menuselect options still build app_voicemail and not
res_mwi_external but if both ARE built, res_mwi_external will load
first and become the voicemail provider unless modules.conf rules
prevent it. This is noted in CHANGES.
Change-Id: I7d98d4e8a3b87b8df9e51c2608f0da6ddfb89247
This patch adds a new module, res_pjsip_history, that provides a slightly
better way of debugging SIP message traffic on a busy Asterisk system. The
existing mechanisms all rely on passively dumping a SIP message to the CLI.
While this is perfectly fine for logging purposes and well controlled
environments, on many installations, the amount of SIP messages Asterisk
receives will quickly swamp the CLI. This makes it difficult to view/capture
those messages that you want to diagnose in real time.
This patch provides another way of handling this. When enabled, the module
will store SIP message traffic in memory. This traffic can then be queried
at leisure.
In order to make the querying useful, a CLI command has been implemented,
'pjsip show history', that supports a basic expression syntax similar to
SQL or other query languages. A small number of useful fields have been
added in this initial patch; additional fields can easily be added in
later improvements. Those fields are:
- number: The entry index in the history
- timestamp: The time the message was recieved
- addr: The source/destination address of the message
- sip.msg.request.method: The request method
- sip.msg.call-id: The Call-ID header
Note - this is a resurrection of the module initially proposed on Review Board
here: https://reviewboard.asterisk.org/r/4053/
Change-Id: I39bd74ce998e99ad5ebc0aab3e84df3a150f8e36
This change introduces the configuration option 'full_backend_cache'
which changes the cache to be a full mirror of the backend instead
of a per-object cache. This allows all sorcery retrieval operations
to be carried out against it and is useful for object types which
are used in a "retrieve all" or "retrieve some" pattern.
ASTERISK-25625 #close
Change-Id: Ie2993487e9c19de563413ad5561c7403b48caab5
This reverts commit f42d22d3a1.
Unfortunately, using a bridge to manage T.38 state will cause severe deadlocks
in core_unreal/chan_local. Local channels attempt to reach across both their
peer and the peer's bridge to inspect T.38 state. Given the propensity of
Local channel chains, managing the locking situation in such a scenario is
practically infeasible.
Change-Id: I932107387c13aad2c75a7a4c1e94197a9d6d8a51
When 4875e5ac32 was merged, it fixed several issues with a direct media bridge
transitioning to handling a T.38 fax. However, it uncovered a race condition
caused by the bridging core. When a channel involved in a T.38 fax leaves a
bridge, the frame queued by the channel driver that should inform the far side
that it is no longer in a T.38 fax may not make it across the bridge. The
bridging framework is *extremely* aggressive in tearing down the bridge, and
control frames that are currently in flight *may* get dropped.
This patch adds a new module to the bridging framework, bridge_t38. This module
maintains some notion of the T.38 state for the two channels in a bridge. When
the bridge detects that it is being torn down or when one of the two channels
leaves, it informs the respective channel(s) that they should stop faxing. This
ensures that channels switch back to audio if they survive and are ejected out
of a bridge while faxing.
ASTERISK-25582
Change-Id: If5b0bb478eb01c4607c9f4a7fc17c7957d260ea0
This patch adds a module that emits StatsD statistics about Asterisk
endpoints. This includes:
* A GAUGE statistic for endpoint states, tracking how many endpoints are in
a particular state.
* A GAUGE statistic for each endpoint, counting the number of channels
currently associated with an endpoint.
ASTERISK-25572
Change-Id: If7e1333c5aeda8d136850b30c2101c0ee1c97305
This patch adds the ability to send StatsD statistics related to the
state of PJSIP contacts. This includes:
* A GUAGE statistic measuring the count of contacts in a particular state.
This measures how many contacts are reachable, unreachable, etc.
* The RTT time for each contact, if those contacts are qualified. This
provides StatsD engines useful time-based data about each contact.
ASTERISK-25571
Change-Id: Ib8378d73afedfc622be0643b87c542557e0b332c
This patch adds outbound registration statistics for StatsD. This includes
the following:
* A GUAGE metric for the overall count of outbound registrations.
* A GUAGE metric for each state an outbound registration can be in. As the
outbound registrations change state, the overall count of how many
outbound registrations are in the particular state is changed.
These statistics are particularly useful for systems with a large number of
SIP trunks, and where measuring the change in state of the trunks is useful
for monitoring.
ASTERISK-25571
Change-Id: Iba6ff248f5d1c1e01acbb63e9f0da1901692eb37
To be able to barge into a call by dialling a prefix+extension that maps
to the extensions device.
Senario is that DECT headset users may be away from their desks and need
to transfer the call, the goal is that from any phone they dial a prefix
then their extension and are added to the bridge that they are in, from
there they can drop the headset call, as it's also on the handset,
and transfer the caller.
The dialplan would look like, where prefix=73, extension = 8512;
exten => _738512,1,BridgeAdd(SIP/cisco0001)
ASTERISK-25551 #close
Reported By: Alec Davis
Change-Id: I8eb5096a02168dcc8d7aeea416ef36ba4ed10540
This option adds the ability to specify a timeout, in seconds, for a
participant in a ConfBridge. When the user's timeout has been reached,
the user is ejected from the conference with the CONFBRIDGE_RESULT
channel variable set to "TIMEOUT".
The rationale for this change is that there have been times where we
have seen channels get "stuck" in ConfBridge because a network issue
results in a SIP BYE not being received by Asterisk. While these
channels can be hung up manually via CLI/AMI/ARI, adding some sort of
automatic cleanup of the channels is a nice feature to have.
ASTERISK-25549 #close
Reported by Mark Michelson
Change-Id: I2996b6c5e16a3dda27595f8352abad0bda9c2d98
CALLERPRES() says that it's deprecated in favor of CALLERID(num-pres)
and CALLERID(name-pres). But for channel driver that don't make a
distinction between the two (e.g. SIP), it makes more sense to get/set
both at once. This change reveals the availability of CALLERID(pres),
CONNECTEDLINE(pres), REDIRECTING(orig-pres), REDIRECTING(to-pres) and
REDIRECTING(from-pres).
ASTERISK-25373 #close
Change-Id: I5614ae4ab7d3bbe9c791c1adf147e10de8698d7a
This patch adds a new setting "websockets_enabled" to sip.conf.
Setting this to false allows chan_sip to be used without causing
conflicts with res_pjsip_transport_websocket.
ASTERISK-24106 #close
Reported by: Andrew Nagy
Change-Id: I04fe8c4f2d57b2d7375e0e25826c91a72e93bea7
Add the ability to filter output from pjsip list and show commands
using the "like" predicate like chan_sip.
For endpoints, aors, auths, registrations, identifyies and transports,
the modification was a simple change of an ast_sorcery_retrieve_by_fields
call to ast_sorcery_retrieve_by_regex. For channels and contacts a
little more work had to be done because neither of those objects are
true sorcery objects. That was just removing the non-matching object
from the final container. Of course, a little extra plumbing in the
common pjsip_cli code was needed to parse the "like" and pass the regex
to the get_container callbacks.
Some of the get_container code in res_pjsip_endpoint_identifier was also
refactored for simplicity.
ASTERISK-25477 #close
Reported by: Bryant Zimmerman
Tested by: George Joseph
Change-Id: I646d9326b778aac26bb3e2bcd7fa1346d24434f1
During outbound registration it is possible to receive a fatal (any permanent/
non-temporary 4xx, 5xx, 6xx) response from the registrar that is simply due
to a problem with the registrar itself. Upon receiving the failure response
Asterisk terminates outbound registration for the given endpoint.
This patch adds an option, 'fatal_retry_interval', that when set continues
outbound registration at the given interval up to 'max_retries' upon receiving
a fatal response.
ASTERISK-25485 #close
Change-Id: Ibc2c7b47164ac89cc803433c0bbe7063bfa143a2
When ab803ec342 was committed, it accidentally forgot to actually *add* the
HOLD_INTERCEPT function. This highlights two interesting points:
* Gerrit forces you to put the patch as it is going to into the repo up for
review, which Review Board did not. Yay Gerrit.
* No one apparently bothered to use this feature, or else they don't know about
it. I'm going to go with the latter explanation.
ASTERISK-24922
Change-Id: Ida38278f259dd07c334a36f9b7d5475b5db72396
In app_queue added value Paused Reason on QueueMemberStatus when a member
on queue is paused and the reason was set.
ASTERISK-25480 #close
Reporte by: Rodrigo Ramírez Norambuena
Change-Id: Ia5db503482f50764c15e2020196c785f59d4a68e
When Asterisk is part of a larger distributed system, log files are often
gathered using tools (such as logstash) that prefer to consume information
and have it rendered using other tools (such as Kibana) that prefer a
structured format, e.g., JSON. This patch adds support for JSON formatted
logs by adding support for an optional log format specifier in Asterisk's
logging subsystem. By adding a format specifier of '[json]':
full => [json]debug,verbose,notice,warning,error
Log messages will be output to the 'full' channel in the following
format:
{
"hostname": Hostname or name specified in asterisk.conf
"timestamp": Date/Time
"identifiers": {
"lwp": Thread ID,
"callid": Call Identifier
}
"logmsg": {
"location": {
"filename": Name of the file that generated the log statement
"function": Function that generated the log statement
"line": Line number that called the logging function
}
"level": Log level, e.g., DEBUG, VERBOSE, etc.
"message": Actual text of the log message
}
}
ASTERISK-25425 #close
Change-Id: I8649bfedf3fb7bf3138008cc11565553209cc238
This patch adds support for receiving events regarding Peer status changes
and Contact status changes. This is particularly useful in scenarios where
we are subscribed to all endpoints and channels, where we often want to know
more about the state of channel technology specific items than a single
endpoint's state.
ASTERISK-24870
Change-Id: I6137459cdc25ce27efc134ad58abf065653da4e9
This patch adds a new option to the CHANNEL function that allows for the
extraction of the SIP call-id. It is used in conjunction with the 'pjsip'
option, and will return the Call-ID of the INVITE request that established
the PJSIP channel.
ASTERISK-25352
Change-Id: I278d1f8bcfe3a53c5aa1dadebc14e92b0abd476a
An http request can be sent to rotate a specified log channel.
If the channel does not exist, an error response will be
returned.
The command "curl -v -u user:pass -X PUT 'http://localhost:8088
/ari/asterisk/logging/logChannelName/rotate'" can be run in the
terminal to access this new functionality.
* Added the ability to rotate log files through ARI
ASTERISK-25252
Change-Id: Iaefa21cbbc1b29effb33004ee3d89c977e76ab01
This change adds support for the 'rtp_timeout' and 'rtp_timeout_hold'
endpoint options. These allow the channel to be hung up if RTP
is not received from the remote endpoint for a specified number of
seconds.
ASTERISK-25259 #close
Change-Id: I3f39daaa7da2596b5022737b77799d16204175b9
This adds an "rtp_keepalive" option for PJSIP endpoints. Similar to the
chan_sip option, this specifies an interval, in seconds, at which we
will send RTP comfort noise frames. This can be useful for keeping RTP
sessions alive as well as keeping NAT associations alive during lulls.
ASTERISK-25242 #close
Reported by Mark Michelson
Change-Id: I3b9903d99e35fe5d0b53ecc46df82c750776bc8d
This patch adds support for push configuration of dynamic, i.e.,
sorcery, objects in Asterisk. It adds three new REST API calls to the
'asterisk' resource:
* GET /asterisk/{configClass}/{objectType}/{id}: retrieve the current
object given its ID. This returns back a list of ConfigTuples, which
define the fields and their present values that make up the object.
* PUT /asterisk/{configClass}/{objectType}/{id}: create or update an
object. A body may be passed with the request that contains fields to
populate in the object. The same format as what is retrieved using
the GET operation is used for the body, save that we specify that the
list of fields to update are contained in the "fields" attribute.
* DELETE /asterisk/{configClass}/{objectType}/{id}: remove a dynamic
object from its backing storage.
Note that the success/failure of these operations is somewhat
configuration dependent, i.e., you must be using a sorcery wizard that
supports the operation in question. If a sorcery wizard does not support
the create or delete mechanisms, then the REST API call will fail with a
403 forbidden.
ASTERISK-25238 #close
Change-Id: I28cd5c7bf6f67f8e9e437ff097f8fd171d30ff5c
An http request can be sent to reload an Asterisk module. If the
module can not be reloaded or is not already loaded, an error
response will be returned.
The command "curl -v -u user:pass -X PUT 'http://localhost:8088
/ari/asterisk/modules/{moduleName}'" (or something similar, based
on configuration) can be run in the terminal to access this new
functionality.
For more information, see:
https://wiki.asterisk.org/wiki.display/~bford/Asterisk+ARI+Resource
* Added new ARI functionality
* Asterisk modules can be reloaded through http requests
ASTERISK-25173
Change-Id: I289188bcae182b2083bdbd9ebfffd50b62f58ae1
An http request can be sent to unload an Asterisk module. If the
module can not be unloaded or is already unloaded, an error response
will be returned.
The command "curl -v -u user:pass -X DELETE 'http://localhost:8088
/ari/asterisk/modules/{moduleName}'" (or something similar, depending
on configuration) can be run in the terminal to access this new
functionality.
For more information, see:
https://wiki.asterisk.org/wiki.display/~bford/Asterisk+ARI+Resource
* Added new ARI functionality
* Asterisk modules can be unloaded through http requests
ASTERISK-25173
Change-Id: I535a95f5676deb02651522761ecbdc0b00b5ac57
An http request can be sent to load an Asterisk module. If the
module can not be loaded or is loaded already, an error response
will be returned.
The command curl -v -u user:pass -X POST 'http://localhost:8088/ari
/asterisk/modules/{moduleName}'" (or something similar, depending on
configuration) can be run in the terminal to access this new
functionality.
For more information, see:
https://wiki.asterisk.org/wiki.display/~bford/Asterisk+ARI+Resource
* Added new ARI functionality
* Asterisk modules can be loaded through http requests
ASTERISK-25173
Change-Id: I9e05d5b8c5c666ecfef341504f9edc1aa84fda33
An http request can be sent to retrieve information on a single
module, including the resource name, description, use count, status,
and support level.
The command "curl -v -u user:pass -X GET 'http://localhost:8088/ari
/asterisk/modules/{moduleName}'" (or something similar, depending on
configuration) can be run in the terminal to access this new
functionality.
For more information, see:
https://wiki.asterisk.org/wiki.display/~bford/Asterisk+ARI+Resource
* Added new ARI functionality
* Information on a single module can now be retrieved
ASTERISK-25173
Change-Id: Ibce5a94e70ecdf4e90329cf0ba66c33a62d37463
An http request can be sent to retrieve a list of all existing modules,
including the resource name, description, use count, status, and
support level.
The command "curl -v -u user:pass -X GET 'http://localhost:8088/ari/
asterisk/modules" (or something similar, depending on configuration)
can be run in the terminal to access this new functionality.
For more information, see:
https://wiki.asterisk.org/wiki.display/~bford/Asterisk+ARI+Resource
* Added new ARI functionality
* Information on modules can now be retrieved
Change-Id: I63cbbf0ec0c3544cc45ed2a588dceabe91c5e0b0
Some phones send g.726 audio packed for AAL2, which differs from what is
recommended by RFC 3351. If Asterisk receives audio formatted as such when
negotiating g.726 then it sounds a bit distorted. Added an option to
res_pjsip_endpoint that allows g.726 negotiated audio to be treated as g.726
AAL2 packed.
ASTERISK-25158 #close
Reported by: Steve Pitts
Change-Id: Ie7e21f75493d7fe53e75e12c971e72f5afa33615
Add a new ContactStatus AMI event.
Publish the following status/state changes:
Created
Removed
Reachable
Unreachable
Unknown
Contact URI, new status/state, aor and endpoint names, and the
last qualify rtt result are included in the event.
ASTERISK-25114 #close
Change-Id: Id25aae5f7122facba183273efb3e8f36c20fb61e
Reported-by: George Joseph <george.joseph@fairview5.com>
Tested-by: George Joseph <george.joseph@fairview5.com>
verification.
This way one X.509 certificate can be used for hosts that
can be reached under multiple DNS names or for multiple hosts.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
ASTERISK-25063 #close
Change-Id: I13302c80490a0b44c43f1b45376c9bd7b15a538f
Previous versions of Asterisk processed command-line options before
processing asterisk.conf. This meant that if an option was set in
asterisk.conf, it could not be overridden with the equivelent command
line option. This change causes Asterisk to process the command-line
twice. First it processes options that are needed to load asterisk.conf,
then it processes the remaining options after the config is read.
This changes the function of -X slightly. Previously using -X without
disabling execincludes in asterisk.conf caused #exec to be usable in any
config. Now -X only enables #exec for the load of asterisk.conf, if it
is wanted in the rest of the system it must be enabled with execincludes
in asterisk.conf. Updated 'asterisk -h' and 'man asterisk' to reflect
the limited function of -X.
ASTERISK-25042 #close
Reported by: Corey Farrell
Change-Id: I1450d45c15b4467274b871914d893ed4f6564cd7
Add feature to set optional schema parameter on configuration file via
'schema' setting.
Fix query to get columns from table while considering schema. If in
the database there exists two tables with same name in distinct schemas
it will return an error when inserting record.
ASTERISK-24967 #close
Change-Id: I691fd2cbc277fcba10e615f5884f8de5d8152f2c
Added the ability to set the character to quote identifiers. This
allows adding the character at the start and end of table and column
names. This setting is configurable for cdr_adaptive_odbc via the
quoted_identifiers in configuration file cdr_adaptive_odbc.conf.
ASTERISK-25006
Change-Id: I0b9a56b79ca13a727a803d88ed3b8643e37632b8
This patch adds a new option to cdr.conf, 'newcdrcolumns', that will handle CDR
columns added in Asterisk 1.8. The columns are:
* peeraccount
* linkedid
* sequence
When enabled, the columns in the database entry will be populated with the data
from the CDR.
ASTERISK-24976 #close
Change-Id: I51a57063f4ae5e194a9d933a8df45dc8a4534f0b
Some telco switches occasionally ignore ISDN RESTART requests. The fix
for ASTERISK-19608 added an escape clause for B channels in the restarting
state if the telco ignores a RESTART request. If the telco fails to
acknowledge the RESTART then Asterisk will assume the telco acknowledged
the RESTART on the second call attempt requesting the B channel by the
telco. The escape clause is good for dealing with RESTART requests in
general but it does cause the next call for the restarting B channel to be
rejected if the telco insists the call must go on that B channel.
chan_dahdi doesn't really need to issue a RESTART request in response to
receiving a cause 44 (Requested channel not available) code. Sending the
RESTART in such a situation is not required (nor prohibited) by the
standards. I think chan_dahdi does this for historical reasons to deal
with buggy peers to get channels unstuck in a similar fashion as the
chan_dahdi.conf resetinterval option.
* Add the chan_dahdi.conf force_restart_unavailable_chans compatability
option that when disabled will prevent chan_dahdi from trying to RESTART
the channel in response to a cause 44 code.
ASTERISK-25034 #close
Reported by: Richard Mudgett
Change-Id: Ib8b17a438799920f4a2038826ff99a1884042f65
Add new column to INSERT new columns added in cdr 1.8 version. The columns are:
* peeraccount
* linkedid
* sequence
This feature is configurable in cdr_odbc.conf using a new configuration
option, 'newcdrcolumns'.
ASTERISK-24976 #close
Change-Id: Ibe0c7540a88305c6012786f438a0813ad8b19127
* changes:
res_pjsip: Add global option to limit the maximum time for initial qualifies
pjsip_options: Add qualify_timeout processing and eventing
res_pjsip: Refactor endpt_send_request to include transaction timeout
Currently when Asterisk starts initial qualifies of contacts are spread out
randomly between 0 and qualify_timeout to prevent network and system overload.
If a contact's qualify_frequency is 5 minutes however, that contact may be
unavailable to accept calls for the entire 5 minutes after startup. So while
staggering the initial qualifies is a good idea, basing the time on
qualify_timeout could leave contacts unavailable for too long.
This patch adds a new global parameter "max_initial_qualify_time" that sets the
maximum time for the initial qualifies. This way you could make sure that all
your contacts are initialy, randomly qualified within say 30 seconds but still
have the contact's ongoing qualifies at a 5 minute interval.
If max_initial_qualify_time is > 0, the formula is initial_interval =
min(max_initial_interval, qualify_timeout * random(). If not set,
qualify_timeout is used.
The default is "0" (disabled).
ASTERISK-24863 #close
Change-Id: Ib80498aa1ea9923277bef51d6a9015c9c79740f4
Tested-by: George Joseph <george.joseph@fairview5.com>
This is the second follow-on to https://reviewboard.asterisk.org/r/4572/ and the
discussion at
http://lists.digium.com/pipermail/asterisk-dev/2015-March/073921.html
The basic issues are that changes in contact status don't cause events to be
emitted for the associated endpoint. Only dynamic contact add/delete actions
update the endpoint. Also, the qualify timeout is fixed by pjsip at 32 seconds
which is a long time.
This patch makes use of the new transaction timeout feature in r4585 and
provides the following capabilities...
1. A new aor/contact variable 'qualify_timeout' has been added that allows the
user to specify the maximum time in milliseconds to wait for a response to an
OPTIONS message. The default is 3000ms. When the timer expires, the contact is
marked unavailable.
2. Contact status changes are now propagated up to the endpoint as follows...
When any contact is 'Available', the endpoint is marked as 'Reachable'. When
all contacts are 'Unavailable', the endpoint is marked as 'Unreachable'. The
existing endpoint events are generated appropriately.
ASTERISK-24863 #close
Change-Id: Id0ce0528e58014da1324856ea537e7765466044a
Tested-by: Dmitriy Serov
Tested-by: George Joseph <george.joseph@fairview5.com>
This change adds the following:
1. A query set implementation. This is an API that allows queries to be executed in parallel and once all have completed a callback is invoked.
2. Unit tests for the query set implementation.
3. An external PJSIP resolver which uses the DNS core API to do NAPTR, SRV, AAAA, and A lookups.
For the resolver it will do NAPTR, SRV, and AAAA/A lookups in parallel. If NAPTR or SRV
are available it will then do more queries. And so on. Preference is NAPTR > SRV > AAAA/A,
with IPv6 preferred over IPv4. For transport it will prefer TLS > TCP > UDP if no explicit
transport has been provided. Configured transports on the system are taken into account to
eliminate resolved addresses which have no hope of completing.
ASTERISK-24947 #close
Reported by: Joshua Colp
Change-Id: I56cb03ce4f9d3d600776f36928e0b3e379b5d71e
This patch adds a new configuration parameter, 'calltokenexpiration', that
controls how long before an authentication call token is expired. The default
maintains the RFC specified 10 seconds. Setting it to a higher value may be
useful in lossy networks.
Review: https://reviewboard.asterisk.org/r/4588
ASTERISK-24939 #close
Reported by: Y Ateya
patches:
ctoken_configuration.diff submitted by Y Ateya (License 6693)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@434563 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds a new option to cel_pgsl, "usegmtime", which causes timestamps
to be logged in GMT.
Review: https://reviewboard.asterisk.org/r/4571/
ASTERISK-23186 #close
Reported by: Rodrigo Ramirez Norambuena
patches:
cel_pgsql.c_add_usegmtime2.patch submitted by Rodrigo Ramirez Norambuena (License 6577)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@434284 65c4cc65-6c06-0410-ace0-fbb531ad65f3
For some applications - such as SLA - a phone pressing hold should not behave
in the fashion that the Asterisk core would like it to. Instead, the hold
action has some application specific behaviour associated with it - such as
disconnecting the channel that initiated the hold; only playing MoH to channels
in the bridge if the channels are of a particular type, etc.
One way of accomplishing this is to use a framehook to intercept the
hold/unhold frames, raise an event, and eat the frame. Tasty. This patch
accomplishes that using a new dialplan function, HOLD_INTERCEPT.
In addition, some general cleanup of raising hold/unhold Stasis messages was
done, including removing some RAII_VAR usage.
Review: https://reviewboard.asterisk.org/r/4549/
ASTERISK-24922 #close
........
Merged revisions 434216 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@434217 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Incoming PJSIP call legs that have not been answered yet send unnecessary
"180 Ringing" or "183 Progress" messages every time a connected line
update happens. If the outgoing channel is also PJSIP then the incoming
channel will always send a "180 Ringing" or "183 Progress" message when
the outgoing channel sends the INVITE.
Consequences of these unnecessary messages:
* The caller can start hearing ringback before the far end even gets the
call.
* Many phones tend to grab the first connected line information and refuse
to update the display if it changes. The first information is not likely
to be correct if the call goes to an endpoint not under the control of the
first Asterisk box.
When connected line first went into Asterisk in v1.8, chan_sip received an
undocumented option "rpid_immediate" that defaults to disabled. When
enabled, the option immediately passes connected line update information
to the caller in "180 Ringing" or "183 Progress" messages as described
above.
* Added "rpid_immediate" option to prevent unnecessary "180 Ringing" or
"183 Progress" messages. The default is "no" to disable sending the
unnecessary messages.
ASTERISK-24781 #close
Reported by: Richard Mudgett
Review: https://reviewboard.asterisk.org/r/4473/
........
Merged revisions 433338 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@433339 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch fixes previously reverted code that caused binary incompatibility
problems with some modules. And like the original patch it makes sure that
no matter what order the endpoint identifier modules were loaded, priority is
given based on the ones specified in the new global 'endpoint_identifier_order'
option.
ASTERISK-24840
Reported by: Mark Michelson
Review: https://reviewboard.asterisk.org/r/4489/
........
Merged revisions 433028 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@433029 65c4cc65-6c06-0410-ace0-fbb531ad65f3
In some countries, privacy laws specify that SMS content cannot be saved by a
provider. This patch adds a new option to the SMS application, 'n', which
prevents the SMS content from being written to the SMS log.
ASTERISK-22591 #close
Reported by: Jan Juergens
patches:
DisableSmsContentLoggingByParam.patch uploaded by Jan Juergens (License 6538)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@432947 65c4cc65-6c06-0410-ace0-fbb531ad65f3
It's possible to have a scenario that will create a conflict between endpoint
identifiers. For instance an incoming call could be identified by two different
endpoint identifiers and the one chosen depended upon which identifier module
loaded first. This of course causes problems when, for example, the incoming
call is expected to be identified by username, but instead is identified by ip.
This patch adds a new 'global' option to res_pjsip called
'endpoint_identifier_order'. It is a comma separated list of endpoint
identifier names that specifies the order by which identifiers are processed
and checked.
ASTERISK-24840 #close
Reported by: Mark Michelson
Review: https://reviewboard.asterisk.org/r/4455/
........
Merged revisions 432638 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@432639 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds a new feature to ARI to redirect a channel to another server,
and fixes a few bugs in PJSIP's handling of the Transfer dialplan
application/ARI redirect capability.
*New Feature*
A new operation has been added to the ARI channels resource, redirect. With
this, a channel in a Stasis application can be redirected to another endpoint
of the same underlying channel technology.
*Bug fixes*
In the process of writing this new feature, two bugs were fixed in the PJSIP
stack:
(1) The existing .transfer channel callback had the limitation that it could
only transfer channels to a SIP URI, i.e., you had to pass
'PJSIP/sip:foo@my_provider.com' to the dialplan application. While this is
still supported, it is somewhat unintuitive - particularly in a world full
of endpoints. As such, we now also support specifying the PJSIP endpoint to
transfer to.
(2) res_pjsip_multihomed was, unfortunately, trying to 'help' a 302 redirect by
updating its Contact header. Alas, that resulted in the forwarding
destination set by the dialplan application/ARI resource/whatever being
rewritten with very incorrect information. Hence, we now don't bother
updating an outgoing response if it is a 302. Since this took a looong time
to find, some additional debug statements have been added to those modules
that update the Contact headers.
Review: https://reviewboard.asterisk.org/r/4316/
ASTERISK-24015 #close
Reported by: Private Name
ASTERISK-24703 #close
Reported by: Matt Jordan
........
Merged revisions 431717 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@431718 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Calling ast_channel_bridge_peer() cannot be done while holding any channel
locks. The reported issue hit the deadlock in chan_iax2, but an audit of
the ast_channel_bridge_peer() calls found three more locations where the
same deadlock can occur.
* Made CHANNEL(peer), res_fax, and the SNMP agent not call
ast_channel_bridge_peer() with any channel locked. For CHANNEL(peer) I
had to rework the logic to not hold the channel lock.
* Made chan_iax2 no longer call ast_channel_bridge_peer(). It was done
for legacy reasons that no longer apply.
* Removed the iax.conf forcejitterbuffer option. It is now always enabled
when the jitterbuffer option is enabled. If you put a jitter buffer on a
channel it will be on the channel.
ASTERISK-24600 #close
Reported by: Jeff Collell
Review: https://reviewboard.asterisk.org/r/4342/
........
Merged revisions 430817 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@430819 65c4cc65-6c06-0410-ace0-fbb531ad65f3
* Made the following AMI actions use list API calls for consistency:
Agents
BridgeInfo
BridgeList
BridgeTechnologyList
ConfbridgeLIst
ConfbridgeLIstRooms
CoreShowChannels
DAHDIShowChannels
DBGet
DeviceStateList
ExtensionStateList
FAXSessions
Hangup
IAXpeerlist
IAXpeers
IAXregistry
MeetmeList
MeetmeListRooms
MWIGet
ParkedCalls
Parkinglots
PJSIPShowEndpoint
PJSIPShowEndpoints
PJSIPShowRegistrationsInbound
PJSIPShowRegistrationsOutbound
PJSIPShowResourceLists
PJSIPShowSubscriptionsInbound
PJSIPShowSubscriptionsOutbound
PresenceStateList
PRIShowSpans
QueueStatus
QueueSummary
ShowDialPlan
SIPpeers
SIPpeerstatus
SIPshowregistry
SKINNYdevices
SKINNYlines
Status
VoicemailUsersList
* Incremented the AMI version to 2.7.0.
* Changed astman_send_listack() to not use the listflag parameter and
always set the value to "Start" so the start capitalization is consistent.
i.e., The FAXSessions used "Start" while the rest of the system used
"start". The corresponding complete event always used "Complete".
* Fixed ami_show_resource_lists() "PJSIPShowResourceLists" to output the
AMI ActionID for all of its list events.
* Fixed off-nominal AMI protocol error in manager_bridge_info(),
manager_parking_status_single_lot(), and
manager_parking_status_all_lots(). Use of astman_send_error() after
responding to the original AMI action request violates the action response
pattern by sending two responses.
* Fixed minor protocol error in action_getconfig() when no requested
categories are found. Each line needs to be formatted as "Header: text".
* Fixed off-nominal memory leak in manager_build_parked_call_string().
* Eliminated unnecessary use of RAII_VAR() in ami_subscription_detail().
ASTERISK-24049 #close
Reported by: Jonathan Rose
Review: https://reviewboard.asterisk.org/r/4315/
........
Merged revisions 430434 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@430435 65c4cc65-6c06-0410-ace0-fbb531ad65f3
With this patch, the following two ARI commands
POST /channels
POST /channels/{id}/continue
Accept a new parameter, label, that can be used to continue to or originate
to a priority label in the dialplan.
Because this is adding a new parameter to ARI commands, the API version of
ARI has been bumped from 1.6.0 to 1.7.0.
This patch comes courtesy of Nir Simionovich from Greenfield Tech. Thanks!
ASTERISK-24412 #close
Reported by Nir Simionovich
Review: https://reviewboard.asterisk.org/r/4285
........
Merged revisions 430337 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@430338 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The current behavior of 'pjsip send unregister' is to send the unregister
(REGISTER with 0 exp) but let the next scheduled register proceed normally.
I don't think that's a good idea. If you unregister, it should stay
unregistered until you decide to start registrations again. So this patch
just adds a cancel_registration call to the current unregister_task to
cancel the timer.
Of course, now you need a way to start registration again so I've added
a 'pjsip send register' command that unregisters and cancels any existing
registration (the same as send unregister), then sends an immediate
registration and starts the timer back up again.
Both changes also ripple to AMI. There's a new PJSIPRegister command.
There's no harm in calling either command repeatedly. They don't care
about the actual state.
Tested-by: George Joseph
Review: https://reviewboard.asterisk.org/r/4301/
........
Merged revisions 430223 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@430224 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds the ability to pass options and a command to MixMontor when
recording a conference using ConfBridge.
New options are -
* record_options: Options to MixMontor, eg: m(), W() etc.
* record_command: The command to execute when recording is over.
* record_file_timestamp: Append the start time to the file name.
These options can also be used with the CONFBRIDGE function, e.g.,
Set(CONFBRIDGE(bridge,record_command)=/path/to/command ^{MIXMONITOR_FILENAME}))
Review: https://reviewboard.asterisk.org/r/4023
ASTERISK-24351 #close
Reported by: Gareth Palmer
patches:
record_command-428838.patch uploaded by Gareth Palmer (License 5169)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@429934 65c4cc65-6c06-0410-ace0-fbb531ad65f3
For the featdmf signaling mode the incoming MF Caller-ID information is
formatted as follows: *${CALLERID(ani2)}${CALLERID(ani)}#*${EXTEN}#
Rather than discarding the ani2 digits, populate the CALLERID(ani2) value
with what is received instead.
AST-1368 #close
Reported by: Denis Martinez
Patches:
extract_ani2_for_featdmf_v11.patch (license #5621) patch uploaded by Richard Mudgett
........
Merged revisions 429783 from http://svn.asterisk.org/svn/asterisk/branches/11
........
Merged revisions 429784 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@429785 65c4cc65-6c06-0410-ace0-fbb531ad65f3
res_pjsip_config_wizard
------------------
* This is a new module that adds streamlined configuration capability for
chan_pjsip. It's targetted at users who have lots of basic configuration
scenarios like 'phone' or 'agent' or 'trunk'. Additional information
can be found in the sample configuration file at
config/samples/pjsip_wizard.conf.sample.
Tested-by: George Joseph
Review: https://reviewboard.asterisk.org/r/4190/
........
Merged revisions 429592 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@429593 65c4cc65-6c06-0410-ace0-fbb531ad65f3
AMI/ARI are getting a few enhancements in the next release of Asterisk 13. Per
semantic versioning, that warrants a bump in the minor version number, as it
reflects a backwards compatible change. Hence, this commit.
........
Merged revisions 429091 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@429092 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Prior to this patch, all Stasis subscriptions would receive a dedicated
thread for servicing published messages. In contrast, prior to r400178
(see review https://reviewboard.asterisk.org/r/2881/), the subscriptions
shared a thread pool. It was discovered during some initial work on Stasis
that, for a low subscription count with high message throughput, the
threadpool was not as performant as simply having a dedicated thread per
subscriber.
For situations where a subscriber receives a substantial number of messages
and is always present, the model of having a dedicated thread per subscriber
makes sense. While we still have plenty of subscriptions that would follow
this model, e.g., AMI, CDRs, CEL, etc., there are plenty that also fall into
the following two categories:
* Large number of subscriptions, specifically those tied to endpoints/peers.
* Low number of messages. Some subscriptions exist specifically to coordinate
a single message - the subscription is created, a message is published, the
delivery is synchronized, and the subscription is destroyed.
In both of the latter two cases, creating a dedicated thread is wasteful (and
in the case of a large number of peers/endpoints, harmful). In those cases,
having shared delivery threads is far more performant.
This patch adds the ability of a subscriber to Stasis to choose whether or not
their messages are dispatched on a dedicated thread or on a threadpool. The
threadpool is configurable through stasis.conf.
Review: https://reviewboard.asterisk.org/r/4193
ASTERISK-24533 #close
Reported by: xrobau
Tested by: xrobau
........
Merged revisions 428681 from http://svn.asterisk.org/svn/asterisk/branches/12
........
Merged revisions 428687 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@428688 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Configuration of DTLS in the general section will be applied to any users
or peers. If configuration exists at their level it overrides the general
section values.
ASTERISK-24128 #close
Reported by: Michael K.
patches:
dtls_default_settings.patch submitted by Michael K. (license 6621)
Review: https://reviewboard.asterisk.org/r/3867/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@427950 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Virtual line support establishes a relationship between messages
related to an outbound registration and a local endpoint. This is
accomplished by attaching a parameter to the Contact of the outbound
registration and looking for it on any received requests. If the
parameter exists and can be matched to an outbound registration
the configured endpoint is associated with the request.
Review: https://reviewboard.asterisk.org/r/2964/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@427165 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When a packet exceeds the MTU, pjproject will switch from UDP to TCP. In
some circumstances (on some networks), this can cause some issues with
messages not getting sent to the correct destination - and can also cause
connections to get dropped due to quirks in pjproject deciding to
terminate TCP connections with no messages.
While fixing the routing/messaging issues is important, having a
configuration option in Asterisk that tells pjproject to not switch over
to TCP would be useful. That way, if some glitch is discovered on some
other network/site, we can at least disable the behavior until a fix is
put into place.
AFS-197 #close
Review: https://reviewboard.asterisk.org/r/4137/
........
Merged revisions 427129 from http://svn.asterisk.org/svn/asterisk/branches/12
........
Merged revisions 427130 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@427137 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The new option 'preferchannelclass' is added to musiconhold.conf. If yes
(the default) the CHANNEL(musicclass) is preferred when choosing the
hold music. If it is no, the class suggested by the application that
calls the MoH (e.g. the Queue() app) gets preferred (new behaviour).
This way you set a different hold-music from the Queue-music by setting
both the CHANNEL(musicclass) and the queue-context musicclass.
ASTERISK-24276 #close
Reported by: Kristian Høgh
Patches:
app_override_channel_moh.patch uploaded by Kristian Høgh (License #6639)
Review: https://reviewboard.asterisk.org/r/4010/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@423893 65c4cc65-6c06-0410-ace0-fbb531ad65f3
- adds sort=randstart (next to sort=, sort=random, sort=alpha)
- combines duplicate moh option parsing code into a single function
- adds deprecationwarnings for application=r to sort randomly
- adds deprecationwarnings for random=yes to sort randomly
- removes invisible code that was supposed to stay until 1.8
The sort=randstart works like sort=alpha, except we start at a random
position.
Review: https://reviewboard.asterisk.org/r/3991/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@423065 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Users now have the ability to bind the rtpengine instance to a specific IP
address. For example, you want chan_sip (call control) on eth0 but rtp (media)
on eth1.
ASTERISK-24280 #close
Reported by: Paul Belanger
Tested by: Paul Belanger
Review: https://reviewboard.asterisk.org/r/3952/
Patches:
rtpengine.diff uploaded by Paul Belanger
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@422241 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch addresses a few issues:
1) The order of Dial events have been changed when performing a call forward.
The order has now been altered to
1) Dial begins dialing channel A.
2) When A forwards the call to B, we issue the dial end event to channel
A, indicating the dial is being canceled due to a forward to B.
3) When the call to channel B occurs, we then issue a new dial begin to
channel B.
2) Call forwards are now reported on the calling channel, not the peer channel.
3) AMI DialEnd events have been altered to display the extension the call is
being forwarded to when relevant.
4) You can now get the values of channel variables for channels that are not
currently in the Stasis application. This brings the retrieval of channel
variables more in line with the rest of channel read operations since they
may be performed on channels not in Stasis.
ASTERISK-24134 #close
Reported by Matt Jordan
ASTERISK-24138 #close
Reported by Matt Jordan
Patches:
forward-shenanigans.diff uploaded by Matt Jordan (License #6283)
Review: https://reviewboard.asterisk.org/r/3899
........
Merged revisions 420794 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@421310 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch gives the optional ability to keep queue rules in RealTime. It is
important to note that with this patch:
(a) Queue rules in RealTime are only examined on module load/reload
(b) Queue rules are loaded both from the queuerules.conf file as well as the
RealTime backend
To inform app_queue to examine RealTime for queue rules, a new setting has been
added to queuerules.conf's general section "realtime_rules". RealTime queue
rules will only be used when this setting is set to "yes".
The schema for the database table supports a rule_name, time, min_penalty, and
max_penalty columns. min_penalty and max_penalty can be relative, if a '-' or
'+' literal is provided. Otherwise, the penalties are treated as constants.
For example:
rule_name, time, min_penalty, max_penalty
'default', '10', '20', '30'
'test2', '20', '30', '55'
'test2', '25', '-11', '+1111'
'test2', '400', '112', '333'
'test3', '0', '4564', '46546'
'test_rule', '40', '15', '50'
which would result in :
Rule: default
- After 10 seconds, adjust QUEUE_MAX_PENALTY to 30 and adjust
QUEUE_MIN_PENALTY to 20
Rule: test2
- After 20 seconds, adjust QUEUE_MAX_PENALTY to 55 and adjust
QUEUE_MIN_PENALTY to 30
- After 25 seconds, adjust QUEUE_MAX_PENALTY by 1111 and adjust
QUEUE_MIN_PENALTY by -11
- After 400 seconds, adjust QUEUE_MAX_PENALTY to 333 and adjust
QUEUE_MIN_PENALTY to 112
Rule: test3
- After 0 seconds, adjust QUEUE_MAX_PENALTY to 46546 and adjust
QUEUE_MIN_PENALTY to 4564
Rule: test_rule
- After 40 seconds, adjust QUEUE_MAX_PENALTY to 50 and adjust
QUEUE_MIN_PENALTY to 15
If you use RealTime, the queue rules will be always reloaded on a module
reload, even if the underlying file did not change. With the option disabled,
the rules will only be reloaded if the file was modified.
Review: https://reviewboard.asterisk.org/r/3607/
ASTERISK-23823 #close
Reported by: Michael K
patches:
app_queue.c_realtime_trunk.patch uploaded by Michael K (License 6621)
........
Merged revisions 420624 from http://svn.asterisk.org/svn/asterisk/branches/13
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@420625 65c4cc65-6c06-0410-ace0-fbb531ad65f3
........
r420089 | mjordan | 2014-08-05 15:10:52 -0500 (Tue, 05 Aug 2014) | 72 lines
ARI: Add channel technology agnostic out of call text messaging
This patch adds the ability to send and receive text messages from various
technology stacks in Asterisk through ARI. This includes chan_sip (sip),
res_pjsip_messaging (pjsip), and res_xmpp (xmpp). Messages are sent using the
endpoints resource, and can be sent directly through that resource, or to a
particular endpoint.
For example, the following would send the message "Hello there" to PJSIP
endpoint alice with a display URI of sip:asterisk@mycooldomain.org:
ari/endpoints/sendMessage?to=pjsip:alice&from=sip:asterisk@mycooldomain.org&body=Hello+There
This is equivalent to the following as well:
ari/endpoints/PJSIP/alice/sendMessage?from=sip:asterisk@mycooldomain.org&body=Hello+There
Both forms are available for message technologies that allow for arbitrary
destinations, such as chan_sip.
Inbound messages can now be received over ARI as well. An ARI application that
subscribes to endpoints will receive messages from those endpoints:
{
"type": "TextMessageReceived",
"timestamp": "2014-07-12T22:53:13.494-0500",
"endpoint": {
"technology": "PJSIP",
"resource": "alice",
"state": "online",
"channel_ids": []
},
"message": {
"from": "\"alice\" <sip:alice@127.0.0.1>",
"to": "pjsip:asterisk@127.0.0.1",
"body": "Watson, come here.",
"variables": []
},
"application": "testsuite"
}
The above was made possible due to some rather major changes in the message
core. This includes (but is not limited to):
- Users of the message API can now register message handlers. A handler has
two callbacks: one to determine if the handler has a destination for the
message, and another to handle it.
- All dialplan functionality of handling a message was moved into a message
handler provided by the message API.
- Messages can now have the technology/endpoint associated with them.
Various other properties are also now more easily accessible.
- A number of ao2 containers that weren't really needed were replaced with
vectors. Iteration over ao2_containers is expensive and pointless when
the lifetime of things is well defined and the number of things is very
small.
res_stasis now has a new file that makes up its structure, messaging. The
messaging functionality implements a message handler, and passes received
messages that match an interested endpoint over to the app for processing.
Note that inadvertently while testing this, I reproduced ASTERISK-23969.
res_pjsip_messaging was incorrectly parsing out the 'to' field, such that
arbitrary SIP URIs mangled the endpoint lookup. This patch includes the
fix for that as well.
Review: https://reviewboard.asterisk.org/r/3726
ASTERISK-23692 #close
Reported by: Matt Jordan
ASTERISK-23969 #close
Reported by: Andrew Nagy
........
r420090 | mjordan | 2014-08-05 15:16:37 -0500 (Tue, 05 Aug 2014) | 2 lines
Remove automerge properties :-(
........
r420097 | mjordan | 2014-08-05 16:36:25 -0500 (Tue, 05 Aug 2014) | 2 lines
test_message: Fix strict-aliasing compilation issue
........
Merged revisions 420089-420090,420097 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@420098 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Now when running PJSIPShowEndpoint, you will receive a
ContactStatusDetail for each bound contact that Asterisk
is qualifying. This information includes the URI of the
contact, current reachability, and roundtrip time.
AFS-91 #close
Reported by Mark Michelson
Review: https://reviewboard.asterisk.org/r/3797
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@419888 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds a new module to Asterisk, res_hep_rtcp. The module subscribes
to the RTCP topics in Stasis and receives RTCP information back from the
message bus. It encodes into HEPv3 packets and sends the information to the
res_hep module for transmission.
Using this, someone with a Homer server can get live call quality monitoring
for all RTP-based channels in their Asterisk 12+ systems.
In addition, there were a few bugs in the RTP engine, res_rtp_asterisk, and
chan_pjsip that were uncovered by the tests written for the Asterisk Test
Suite. This patch fixes the following:
1) chan_pjsip failed to set its channel unique ids on its RTP instance on
outbound calls. It now does this in the appropriate location, in the
serialized call callback.
2) The rtp_engine was overflowing some values when packed into JSON.
Specifically, some longs and unsigned ints can't be be packed into integer
values, for obvious reasons. Since libjansson only supports integers,
floats, strings, booleans, and objects, we print these values into strings.
3) res_rtp_asterisk had a few problems:
(a) it would emit a source IP address of 0.0.0.0 if bound to that IP
address. We now use ast_find_ourip to get a better IP address, and
properly marshal the result into an ast_strdupa'd string.
(b) Reports can be generated with no report bodies. In particular, this
occurs when a sender is transmitting information to a receiver (who
will send no RTP back to the sender). As such, the sender has no report
body for what it received. We now properly handle this case, and the
sender will emit SR reports with no body. Likewise, if we receive an
RTCP packet with no report body, we will still generate the appropriate
events.
ASTERISK-24119 #close
........
Merged revisions 419823 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@419825 65c4cc65-6c06-0410-ace0-fbb531ad65f3
........
r419565 | mjordan | 2014-07-25 09:41:23 -0500 (Fri, 25 Jul 2014) | 21 lines
ARI: report duration values in LiveRecording objects
This patch adds three new fields to the LiveRecording model:
- total_duration: the total length of the live recording
- talking_duration: optional. The duration of talking energy that was
detected while the recording was made.
- silence_duration: optional. The duration of silence that was detected while
the recording was made.
These values are reported in the RecordingFinished ARI event.
When a DSP is enabled on the channel during the recording - which occurs when
the recording is created with max_silence_seconds (indicating that the user
actually cares about how much silence is in the file), we will report the
talking_duration and silence_duration in addition to the total_duration.
Review: https://reviewboard.asterisk.org/r/3770/
ASTERISK-24037 #close
Reported by: Samuel Galarneau
........
r419566 | mjordan | 2014-07-25 09:46:15 -0500 (Fri, 25 Jul 2014) | 1 line
Update CHANGES for r419565
........
Merged revisions 419565-419566 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@419567 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The previous behavior was to simply set the accountcode of an outgoing
channel to the accountcode of the channel initiating the call. It was
done this way a long time ago to allow the accountcode set on the SIP/100
channel to be propagated to a local channel so the dialplan execution on
the Local;2 channel would have the SIP/100 accountcode available.
SIP/100 -> Local;1/Local;2 -> SIP/200
Propagating the SIP/100 accountcode to the local channels is very useful.
Without any dialplan manipulation, all channels in this call would have
the same accountcode.
Using dialplan, you can set a different accountcode on the SIP/200 channel
either by setting the accountcode on the Local;2 channel or by the Dial
application's b(pre-dial), M(macro) or U(gosub) options, or by the
FollowMe application's b(pre-dial) option, or by the Queue application's
macro or gosub options. Before Asterisk v12, the altered accountcode on
SIP/200 will remain until the local channels optimize out and the
accountcode would change to the SIP/100 accountcode.
Asterisk v1.8 attempted to add peeraccount support but ultimately had to
punt on the support. The peeraccount support was rendered useless because
of how the CDR code needed to unconditionally force the caller's
accountcode onto the peer channel's accountcode. The CEL events were thus
intentionally made to always use the channel's accountcode as the
peeraccount value.
With the arrival of Asterisk v12, the situation has improved somewhat so
peeraccount support can be made to work. Using the indicated example, the
the accountcode values become as follows when the peeraccount is set on
SIP/100 before calling SIP/200:
SIP/100 ---> Local;1 ---- Local;2 ---> SIP/200
acct: 100 \/ acct: 200 \/ acct: 100 \/ acct: 200
peer: 200 /\ peer: 100 /\ peer: 200 /\ peer: 100
If a channel already has an accountcode it can only change by the
following explicit user actions:
1) A channel originate method that can specify an accountcode to use.
2) The calling channel propagating its non-empty peeraccount or its
non-empty accountcode if the peeraccount was empty to the outgoing
channel's accountcode before initiating the dial. e.g., Dial and
FollowMe. The exception to this propagation method is Queue. Queue will
only propagate peeraccounts this way only if the outgoing channel does not
have an accountcode.
3) Dialplan using CHANNEL(accountcode).
4) Dialplan using CHANNEL(peeraccount) on the other end of a local
channel pair.
If a channel does not have an accountcode it can get one from the
following places:
1) The channel driver's configuration at channel creation.
2) Explicit user action as already indicated.
3) Entering a basic or stasis-mixing bridge from a peer channel's
peeraccount value.
You can specify the accountcode for an outgoing channel by setting the
CHANNEL(peeraccount) before using the Dial, FollowMe, and Queue
applications. Queue adds the wrinkle that it will not overwrite an
existing accountcode on the outgoing channel with the calling channels
values.
Accountcode and peeraccount values propagate to an outgoing channel before
dialing. Accountcodes also propagate when channels enter or leave a basic
or stasis-mixing bridge. The peeraccount value only makes sense for
mixing bridges with two channels; it is meaningless otherwise.
* Made peeraccount functional by changing accountcode propagation as
described above.
* Fixed CEL extracting the wrong ie value for the peeraccount. This was
done intentionally in Asterisk v1.8 when that version had to punt on
peeraccount.
* Fixed a few places dealing with accountcodes that were reading from
channels without the lock held.
AFS-65 #close
Review: https://reviewboard.asterisk.org/r/3601/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@419520 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Say you wanted to include variables in an application map and have those
variables substituted and passed along to the application being executed;
currently this does not happen.
This patch adds this ability to pass channel variable values to an
application before being executed.
ASTERISK-22608 #close
Reported by: Michael L. Young
patches:
features_substitute_arguments_v2.diff
uploaded by Michael L. Young (license 5026)
Review: https://reviewboard.asterisk.org/r/3819/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@419252 65c4cc65-6c06-0410-ace0-fbb531ad65f3
We have a new periodic beep feature but sometimes a user needs some sort of
feedback, without the need to have a periodic beep during the recording, to let
them know that MixMonitor started recording or ended the recording. The use
case where this patch is being used is when using Dynamic Features to start and
end MixMonitor.
This patch adds an option to play a beep when MixMonitor starts and an option to
play a beep when MixMonitor ends.
ASTERISK-24051 #close
Reported by: Michael L. Young
patches:
mixmonitor-play-beep-start-stop.diff
uploaded by Michael L. Young (license 5026)
Review: https://reviewboard.asterisk.org/r/3820/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@419238 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds a new operation for stored recordings, copy. It takes an
existing stored recording and makes a copy of it in the same directory
or a relative directory under the stored recording directory.
/ari/recordings/stored/{recordingName}/copy?destinationRecordingName={copy_name}
This is particularly useful for voicemail-esque applications, which may need to
copy or move recordings around a directory structure.
Review: https://reviewboard.asterisk.org/r/3768/
ASTERISK-24036 #close
Reported by: Sam Galarneau
Tested by: Sam Galarneau
........
Merged revisions 419021 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@419022 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Whenever possible, audiohooks and framehooks will now be copied over
to the channel that the masquerading channel gets cloned into. This
should occur for all audiohooks and most framehooks. As a result,
in Asterisk 12.5 and up, the AUDIOHOOK_INHERIT function is now
deprecated and its behavior is essentially the new default for all
audiohooks, plus some additional audiohooks/framehooks.
Review: https://reviewboard.asterisk.org/r/3721/
........
Merged revisions 418914 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@418936 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Most channel drivers let you specify a default accountcode to be set on
channels associated with a particular peer/endpoint/object. Prior to this
patch, chan_pjsip/res_pjsip did not support such a setting.
This patch adds a new setting to the res_pjsip endpoint object, 'accountcode'.
When a channel is created that is associated with an endpoint with this value
set, the channel will automatically have its accountcode property set to the
value configured for the endpoint.
Review: https://reviewboard.asterisk.org/r/3724/
ASTERISK-24000 #close
Reported by: Matt Jordan
........
Merged revisions 418756 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@418757 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds support for the PostgreSQL application_name connection setting.
When the appropriate PostgreSQL module's configuration is set with an
application name, the name will be passed to PostgreSQL on connection and
displayed in the database's pg_stat_activity view, as well as in CSV logs. This
aids in managing which applications/servers are connected to a PostgreSQL
database, as well as tracing the activity of those connections.
Review: https://reviewboard.asterisk.org/r/3591
ASTERISK-23737 #close
Reported by: Gergely Domodi
patches:
pgsql_application_name.patch uploaded by Gergely Domodi (License 6610)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@418755 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Billing records are fair,
To get paid is quite bright,
You should really use ODBC;
Good-bye cdr_sqlite.
Microsoft did once push H.323,
Hell, we all remember NetMeeting.
But try to compile chan_h323 now
And you will take quite a beating.
The XMPP and SIP war was fierce,
And in the distant fray
Was birthed res_jabber/chan_jingle;
But neither to stay.
For everyone did care and chase what Google professed.
"Free Internet Calling" was what devotees cried,
But Google did change the specs so often
That the developers were happy the day chan_gtalk died.
And then there was that odd application
Dedicated to the Polish tongue.
app_saycountpl was subsumed by Say;
One could say its bell was rung.
To read and parse a file from the dialplan
You could (I guess) use an application.
app_readfile did fill that purpose, but I think
A function is perhaps better in its creation.
Barging is rude, I'm not sure why we do it.
Inwardly, the caller will probably sigh.
But if you really must do it,
Don't use app_dahdibarge, use ChanSpy.
We all despise the sound of tinny robots
It makes our queues so cold.
To control such an abomination
It's better to not use Wait/SetMusicOnHold.
It's often nice to know properties of a channel
It makes our calls right
We have a nice function called CHANNEL
And so SIPCHANINFO is sent off into the night.
And now things get odd;
Apparently one could delimit with a colon
Properties from the SIPPEER function!
Commas are in; all others are done.
Finally, a word on pipes and commas.
We're sorry. We can't say it enough.
But those compatibility options in asterisk.conf;
To maintain them forever was just too tough.
This patch removes:
* cdr_sqlite
* chan_gtalk
* chan_jingle
* chan_h323
* res_jabber
* app_saycountpl
* app_readfile
* app_dahdibarge
It removes the following applications/functions:
* WaitMusicOnHold
* SetMusicOnHold
* SIPCHANINFO
It removes the colon delimiter from the SIPPEER function.
Finally, it also removes all compatibility options that were configurable from
asterisk.conf, as these all applied to compatibility with Asterisk 1.4 systems.
Review: https://reviewboard.asterisk.org/r/3698/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@418019 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch enables Perfect Forward Secrecy (PFS) in Asterisk's core TLS API.
Modules that wish to enable PFS should consider the following:
- Ephemeral ECDH (ECDHE) is enabled by default. To disable it, do not
specify a ECDHE cipher suite in a module's configuration, for example:
tlscipher=AES128-SHA:DES-CBC3-SHA
- Ephemeral DH (DHE) is disabled by default. To enable it, add DH parameters
into the private key file, i.e., tlsprivatekey. For an example, see the
default dh2048.pem at
http://www.opensource.apple.com/source/OpenSSL098/OpenSSL098-35.1/src/apps/dh2048.pem?txt
- Because clients expect the server to prefer PFS, and because OpenSSL sorts
its cipher suites by bit strength, (see "openssl ciphers -v DEFAULT")
consider re-ordering your cipher suites in the conf file. For example:
tlscipher=AES128+kEECDH:AES128+kEDH:3DES+kEDH:AES128-SHA:DES-CBC3-SHA:-ADH:-AECDH
will use PFS when offered by the client. Clients which do not offer PFS
fall-back to AES-128 (or even 3DES as recommend by RFC 3261).
Review: https://reviewboard.asterisk.org/r/3647/
ASTERISK-23905 #close
Reported by: Alexander Traud
patches:
tlsPFS_for_HEAD.patch uploaded by Alexander Traud (License 6520)
tlsPFS.patch uploaded by Alexander Traud (License 6520)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@417803 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds support for the Japanese language to both the say family of
applications, as well as for VoiceMail and VoiceMailMain. A new pack of
language sounds will be released at the same time as the next major version
of Asterisk to support the new language features.
The language features can be enabled using a language code of 'ja'.
Review: https://reviewboard.asterisk.org/r/3477
ASTERISK-23324 #close
Reported by: Kevin McCoy
patches:
app_voicemail.c.20140226.jb.patch uploaded by Kevin McCoy (License 6586)
say.c.20140226.jb.patch uploaded by Kevin McCoy (License 6586)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@417591 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch enables the jack-audiohook to cope with dynamic sampling rates from
and to Asterisk. Information from the channel is taken to derive the channel's
sampling rate, suiting SLINxx format and frame->datalen.
There are stil a few limitations after this patch:
* Required information is taken from the channel during initialization as
the audiohook does not provide this information.
Audiohook.internal_sampl_rate(...) is set later, but no callback is available
to inform app_jack.
* Frame.datalen is computed using "rate / 50" assuming a ptime of 20ms.
There is no internal API available to determine datalen for a SLINxx.
* Ringbuffer size is now dynamic depending on the value of frame.datalen
(see above) and the number of frames, which are in RINGBUFFER_FRAME_CAPACITY,
that need to fit.
Review: https://reviewboard.asterisk.org/r/3618
Note that the patch being committed here is based on the patch posted on
ASTERISK-23836. However, Matthis Schmieder also provided a patch to enable
this functionality, and that patch is noted below.
ASTERISK-20696 #close
Reported by: Matthis Schmieder
patches:
app_jack.patch uploaded by Matthis Schmieder (License 6445)
ASTERISK-23836 #close
Reported by: Dennis Guse
patches:
patch-app_jack.c uploaded by Dennis Guse (License 6513)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@417360 65c4cc65-6c06-0410-ace0-fbb531ad65f3
* SS7 support now requires libss7 v2.0 or later. The new libss7 is not
backwards compatible.
* Added SS7 support for connected line and redirecting.
* Most SS7 CLI commands are reworked as well as new SS7 commands added.
See online CLI help.
* Added several SS7 config option parameters described in
chan_dahdi.conf.sample.
* ISUP timer support reworked and now requires explicit configuration.
See ss7.timers.sample.
Special thanks to Kaloyan Kovachev for his support and persistence in
getting the original patch by adomjan updated and ready for release.
SS7-27 #close
Reported by: adomjan
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@416416 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds a new channel function TALK_DETECT that, when set on a
channel, causes events indicating the start/stop of talking on a channel to be
emitted to both AMI and ARI clients.
The function allows setting both the silence threshold (the length of silence
after which we decide no one is talking) as well as the talking threshold (the
amount of energy that counts as talking). Parameters can be updated on a channel
after talk detection has been enabled, and talk detection can be removed at
any time.
The events raised by the function use a nomenclature similar to existing AMI/ARI
events.
For AMI: ChannelTalkingStart/ChannelTalkingStop
For ARI: ChannelTalkingStarted/ChannelTalkingFinished
Review: https://reviewboard.asterisk.org/r/3563/
#ASTERISK-23786 #close
Reported by: Matt Jordan
........
Merged revisions 414934 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@414935 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Improvements to the agent pool functionality.
* AgentRequest no longer hangs up the caller if the agent fails to connect
with the caller. It now continues in the dialplan.
* AgentRequest returns AGENT_STATUS set to NOT_CONNECTED if the agent
failed to connect with the call. Most likely because the agent did not
acknowledge the call in time or got disconnected.
* The agent alerting play file configured by the agent.conf custom_beep
option can now be disabled by setting the option to an empty string. The
agent is effectively alerted to a call presence when MOH stops.
* Fixed bridge reference leak when the agent connects with a caller.
ASTERISK-23499 #close
Reported by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/3551/
........
Merged revisions 414747 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@414748 65c4cc65-6c06-0410-ace0-fbb531ad65f3
User events can now be generated from ARI. Events can be signalled with
arbitrary json variables, and include one or more of channel, bridge, or
endpoint snapshots. An application must be specified which will receive
the event message (other applications can subscribe to it). The message
will also be delivered via AMI provided a channel is attached. Dialplan
generated user event messages are still transmitted via the channel, and
will only be received by a stasis application they are attached to or if
the channel is subscribed to.
This change also introduces the multi object blob mechanism used to send
multiple snapshot types in a single message. The dialplan app UserEvent
was also changed to use multi object blob, and a new stasis message type
created to handle them.
ASTERISK-22697 #close
Review: https://reviewboard.asterisk.org/r/3494/
........
Merged revisions 414405 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@414406 65c4cc65-6c06-0410-ace0-fbb531ad65f3
In r411189, some behavior was changed which made sendrpid behavior
act in a more trusting manner by sending full user data for peers
set with private caller presence in P-Asserted-Identity headers.
Since this changed long time expected behaviors, we decided to pull
that patch when that was pointed out by the community. Instead, this
patch provides a trust_id_outbound setting which will expose the data
per RFC-3325 if set to 'yes' and simply not send the PAI/RPID headers
at all if set to 'no'. By default trust_id_outbound will be set to
'legacy' which will preserve the behavior prior to these patches.
Extra special thanks to Walter Doekes for providing advice and
feedback.
(closes issue AST-1301)
(closes issue ASTERISK-19465)
Reported by: Krzysztof Chmielewski
Review: https://reviewboard.asterisk.org/r/3447/
........
Merged revisions 412744 from http://svn.asterisk.org/svn/asterisk/branches/1.8
........
Merged revisions 412746 from http://svn.asterisk.org/svn/asterisk/branches/11
........
Merged revisions 412747 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@412759 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Adds a tones URI type to the playback resource. The tone can be specified by
name (from indications.conf) or by a tone pattern. In addition, tonezone can
be specified in the URI (by appending ;tonezone=<zone>). Tones must be
stopped manually in order for a stasis control to move on from playback of
the tone. Tones may be paused, resumed, restarted, and stopped. They may
not be rewound or fast forwarded (tones can't be controlled in a way that
lets you skip around from note to note and pausing and resuming will also
restart the tone from the beginning). Tests are currently in development
for this feature (https://reviewboard.asterisk.org/r/3428/).
(closes issue ASTERISK-23433)
Reported by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/3427/
........
Merged revisions 412535 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@412536 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch is a continuation of https://reviewboard.asterisk.org/r/3349/,
committed in r412303.
It resolves a finding oej had that the phone-context be available in a
channel variable separate from SIPDOMAIN. This patch adds that variable as
SIPURIPHONECONTEXT. It also allows a local number (or global number specified
in the TEL URI) to be used to look up as a peer.
(issue ASTERISK-17179)
Review: https://reviewboard.asterisk.org/r/3349/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@412467 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Add an option to enable a periodic beep to be played into a call if it
is being recorded. If enabled, it uses the PERIODIC_HOOK() function
internally to play the 'beep' prompt into the call at a specified
interval. This option is provided for both Monitor() and
MixMonitor().
Review: https://reviewboard.asterisk.org/r/3424/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@412427 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds support for handling TEL URIs in inbound INVITE requests.
This includes the Request URI and the From URI. The number specified in
the Request URI will be the destination of the inbound channel in the dialplan.
The phone-context specified in the Request URI will be stored in the
TELPHONECONTEXT channel variable.
Review: https://reviewboard.asterisk.org/r/3349
ASTERISK-17179 #close
Reported by: Geert Van Pamel
Tested by: Geert Van Pamel
patches:
asterisk-12.0.0-chan_sip-RFC3966_patch.txt uploaded by Geert Van Pamel (License 6140)
asterisk-12.0.0-reqresp_parser-RFC3966_patch.txt uploaded by Geert Van Pamel (License 6140)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@412292 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This fixes a parsing error that occurred during the processing of
the AMI action. The error did not result in MixMonitor itself
misbehaving, but it could result in the AMI response not giving
correct information back.
The new header allows for one to specify a post-process command
to run when recording finishes. Previously, in order to do this,
the post-process command would have to be placed at the end of
the Options: header.
Patches: mixmonitor_command_2.patch by jhardin (License #6512)
........
Merged revisions 412048 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@412050 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This commit introduces a new dialplan function, PERIODIC_HOOK().
It allows you run to a dialplan hook on a channel periodically. The
original use case that inspired this was the ability to play a beep
periodically into a call being recorded. The implementation is much
more generic though and could be used for many other things.
The implementation makes heavy use of existing Asterisk components.
It uses a combination of Local channels and ChanSpy() to run some
custom dialplan and inject any audio it generates into an active call.
The other important bit of the implementation is how it figures out
when to trigger the beep playback. This implementation uses the
audiohook API, even though it's not actually touching the audio in any
way. It's a convenient way to get a callback and check if it's time
to kick off another beep. It would be nice if this was timer event
based instead of polling based, but unfortunately I don't see a way to
do it that won't interfere with other things.
Review: https://reviewboard.asterisk.org/r/3362/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@411768 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds the following:
(1) A new module, res_hep, which implements a generic packet capture agent for
the Homer Encapsulation Protocol (HEP) version 3. Note that this code is based
on a patch provided by Alexandr Dubovikov; I basically just wrapped it up,
added configuration via the configuration framework, and threw in a
taskprocessor.
(2) A new module, res_hep_pjsip, which forwards all SIP message traffic that
passes through the res_pjsip stack over to res_hep for encapsulation and
transmission to a HEPv3 capture server.
Much thanks to Alexandr for his Asterisk patch for this code and for a *lot*
of patience waiting for me to port it to 12/trunk. Due to some dithering on
my part, this has taken the better part of a year to port forward (I still
blame CDRs for the delay).
ASTERISK-23557 #close
Review: https://reviewboard.asterisk.org/r/3207/
........
Merged revisions 411534 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@411556 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch does the following:
* It updates the AMI version to 2.2.0 to indicate backwards compatible
changes have been made since the last release
* It updates the ARI version to 1.2.0 to indicate backwards compatible
changes have been made since the last release
* It updates the UPGRADE/CHANGES files with changes that were not
mentioned
........
Merged revisions 411529 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@411530 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This change turns the bridge type field into a comma separated list of attributes.
These attributes include: mixing, holding, dtmf_events, and proxy_media. By setting
the various attributes a user can control the type of bridge created with the
behavior they need for their application.
(closes issue ASTERISK-23437)
Reported by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/3359/
........
Merged revisions 410904 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@410905 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This change enables DNS client support within PJSIP. System
nameservers are automatically discovered using res_init or
res_ninit. If this fails then PJSIP will resort to using
gethostbyname for resolution.
By enabling this support we gain SRV support, failover, and
weight support.
(closes issue ASTERISK-23435)
Reported by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/3343/
........
Merged revisions 410795 from http://svn.asterisk.org/svn/asterisk/branches/12
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@410796 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch creates the AST_SORCERY dialplan function which allows someone to
retrieve any value from a sorcery-based config file. It's similar to
AST_CONFIG.
The creation of the function itself was fairly straightforward but it required
changes to the underlying sorcery infrastructure that rippled into individual
sorcery objects. The changes stemmed from inconsistencies in how sorcery
created ast_variable objectsets from sorcery objects and the inconsistency
in how individual objects used that feature especially when it came to
parameters that can be specified multiple times like contact in aor and match
in identify. You can read more here...
http://lists.digium.com/pipermail/asterisk-dev/2014-February/065202.html
So, what this patch does, besides actually creating the AST_SORCERY function,
is the following...
* Creates ast_variable_list_append which is a helper to append one ast_variable
list to another.
* Modifies the ast_sorcery_object_field_register functions to accept the
already-defined sorcery_fields_handler callback.
* Modifies ast_sorcery_objectset_create to accept a parameter indicating return
type preference...a single ast_variable with all values concatenated or an
ast_variable list with multiple entries. Also fixed a few bugs.
* Modifies individual sorcery object implementations to use the new function
definition of the ast_sorcery_object_field_register functions.
* Modifies location.c and res_pjsip_endpoint_identifier_ip.c to implement
sorcery_fields_handler handlers so they return multiple occurrences as an
ast_variable_list.
* Added a whole bunch of tests to test_sorcery.
(closes issue ASTERISK-22537)
Review: http://reviewboard.asterisk.org/r/3254/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@410042 65c4cc65-6c06-0410-ace0-fbb531ad65f3
George Joseph
Matt Jordan
Joshua Colp
Alexander Traud
Niklas Larsson
David M. Lee
Alec Davis
Mark Michelson
Walter Doekes
Corey Farrell
Kevin Harwell
Rodrigo Ramírez Norambuena
Benjamin Ford
Richard Mudgett
Maciej Szmigiero
Rodrigo Ramírez Norambuena
Kinsey Moore
Paul Belanger
Jason Parker
Jonathan Rose
Michael L. Young
Scott Griepentrog
Igor Goncharovskiy
Russell Bryant