A new endpoint parameter "incoming_mwi_mailbox" allows Asterisk to
receive unsolicited MWI NOTIFY requests and make them available to
other modules via the stasis message bus.
res_pjsip_pubsub has a new handler "pubsub_on_rx_mwi_notify_request"
that parses a simple-message-summary body and, if
endpoint->incoming_mwi_account is set, calls ast_publish_mwi_state
with the voice-message counts from the message.
Change-Id: I08bae3d16e77af48fcccc2c936acce8fc0ef0f3c
If an error occurs during a bridge impart it's possible that
the "bridge_after" callback might try to run before
control_swap_channel_in_bridge has been signalled to continue.
Since control_swap_channel_in_bridge is holding the control lock
and the callback needs it, a deadlock will occur.
* control_swap_channel_in_bridge now only holds the control
lock while it's actually modifying the control structure and
releases it while the bridge impart is running.
* bridge_after_cb is now tolerant of impart failures.
Change-Id: Ifd239aa93955b3eb475521f61e284fcb0da2c3b3
In 2dee95cc (ASTERISK-27024) and 776ffd77 (ASTERISK-26879) there was
confusion about whether the transport_state->localnet ACL has ALLOW or
DENY semantics.
For the record: the localnet has DENY semantics, meaning that "not in
the list" means ALLOW, and the local nets are in the list.
Therefore, checks like this look wrong, but are right:
/* See if where we are sending this request is local or not, and if
not that we can get a Contact URI to modify */
if (ast_apply_ha(transport_state->localnet, &addr) != AST_SENSE_ALLOW) {
ast_debug(5, "Request is being sent to local address, "
"skipping NAT manipulation\n");
(In the list == localnet == DENY == skip NAT manipulation.)
And conversely, other checks that looked right, were wrong.
This change adds two macro's to reduce the confusion and uses those
instead:
ast_sip_transport_is_nonlocal(transport_state, addr)
ast_sip_transport_is_local(transport_state, addr)
ASTERISK-27248 #close
Change-Id: Ie7767519eb5a822c4848e531a53c0fd054fae934
An admin can configure app_minivm with an externnotify program to be run
when a voicemail is received. The app_minivm application MinivmNotify
uses ast_safe_system() for this purpose which is vulnerable to command
injection since the Caller-ID name and number values given to externnotify
can come from an external untrusted source.
* Add ast_safe_execvp() function. This gives modules the ability to run
external commands with greater safety compared to ast_safe_system().
Specifically when some parameters are filled by untrusted sources the new
function does not allow malicious input to break argument encoding. This
may be of particular concern where CALLERID(name) or CALLERID(num) may be
used as a parameter to a script run by ast_safe_system() which could
potentially allow arbitrary command execution.
* Changed app_minivm.c:run_externnotify() to use the new ast_safe_execvp()
instead of ast_safe_system() to avoid command injection.
* Document code injection potential from untrusted data sources for other
shell commands that are under user control.
ASTERISK-27103
Change-Id: I7552472247a84cde24e1358aaf64af160107aef1
If an SDP answer hasn't been sent yet, it's legal to change it.
This is required for PJSIP_DTMF_MODE to work correctly, and can
also have use in the future for updating codecs too.
ASTERISK-27209 #close
Change-Id: Idbbfb7cb3f72fbd96c94d10d93540f69bd51e7a1
* Fix deadlock in
bridge_softmix.c:softmix_bridge_stream_topology_changed() between
bridge_channel and channel locks.
* The new bridge technology topology change callbacks must be called with
the bridge locked. The callback references the bridge channel list, the
bridge technology could change, and the bridge stream mapping is updated.
ASTERISK-27212
Change-Id: Ide4360ab853607e738ad471721af3f561ddd83be
* ast_channel_request_stream_topology_change() must not be called with any
channel locks held.
* ast_channel_stream_topology_changed() must be called with only the
passed channel lock held.
ASTERISK-27212
Change-Id: I843de7956d9f1cc7cc02025aea3463d8fe19c691
The fix for the issue is broken up into three parts.
This is part two which handles the server side of REGISTER requests when
rewrite_contact is enabled. Any registered reliable transport contact
becomes invalid when the transport connection becomes disconnected.
* Monitor the rewrite_contact's reliable transport REGISTER contact for
shutdown. If it is shutdown then the contact must be removed because it
is no longer valid. Otherwise, when the client attempts to re-REGISTER it
may be blocked because the invalid contact is there. Also if we try to
send a call to the endpoint using the invalid contact then the endpoint is
not likely to see the request. The endpoint either won't be listening on
that port for new connections or a NAT/firewall will block it.
* Prune any rewrite_contact's registered reliable transport contacts on
boot. The reliable transport no longer exists so the contact is invalid.
* Websockets always rewrite the REGISTER contact address and the transport
needs to be monitored for shutdown.
* Made the websocket transport set a unique name since that is what we use
as the ao2 container key. Otherwise, we would not know which transport we
find when one of them shuts down. The names are also used for PJPROJECT
debug logging.
* Made the websocket transport post the PJSIP_TP_STATE_CONNECTED state
event. Now the global keep_alive_interval option, initially idle shutdown
timer, and the server REGISTER contact monitor can work on wetsocket
transports.
* Made the websocket transport set the PJSIP_TP_DIR_INCOMING direction.
Now initially idle websockets will automatically shutdown.
ASTERISK-27147
Change-Id: I397a5e7d18476830f7ffe1726adf9ee6c15964f4
The fix for the issue is broken up into three parts.
This is part one which refactors the transport state monitor code to allow
more modules to be able to monitor transports.
* Pull the management of PJPROJECT's transport state callback code from
res_pjsip_transport_management.c into res_pjsip. Now other modules can
dynamically add and remove themselves from transport monitoring without
worrying about breaking PJPROJECT's callback chain.
* Add the ability for other modules to get a callback whenever a specific
transport is shutdown.
ASTERISK-27147
Change-Id: I7d9a31371eb1487c9b7050cf82a9af5180a57912
Introduce a new property to rtp-engine to make it aware of
the desire for assymetric codecs or not. If asymmetric codecs
is not allowed, the bridge will compare read/write formats
and shut down the p2p bridge if needed
ASTERISK-26745 #close
Change-Id: I0d9c83e5356df81661e58d40a8db565833501a6f
Currently, the handling of the msid attribute is not quite right. According to
the spec the msid's between the offer/answer are not dependent upon one another.
Meaning the same msid's given in an offer do not have to be returned in the
answer for a given stream. And they probably shouldn't be (copied/reused) since
this can potentially cause some browser side confusion.
This patch generates new msids when both an offer and answer are sent from
Asterisk. However, Asterisk does reuse the original msid it sent out for a
reinvite. Also audio+video streams are paired together by sharing the same
stream id, but a different track id.
ASTERISK-27179 #close
Change-Id: Ifaec06dc7e65ad841633a24ebec8c8a9302d6643
The "external_media_address" option on transports is now
resolved using dnsmgr. This allows it to be automatically
refreshed regularly if refreshes are enabled in dnsmgr.
If the system is using a dynamic IP address a dynamic DNS
hostname can be provided to keep the IP address up to
date.
Change-Id: Ia54771720dff0105bde55d5bbb81a3ba437e05b2
This function is a replica of SIPDtmfMode, allowing the DTMF mode of a
PJSIP call to be modified on a per-call basis
ASTERISK-27085 #close
Change-Id: I20eef5da3e5d1d3e58b304416bc79683f87e7612
AMI goes from 3.2.0 to 4.0.0
ARI goes from 2.0.0 to 3.0.0
Copied UPGRADE.txt -> UPGRADE-15.txt
Created new UPGRADE.txt
Removed a log file that was accidentally checked in a while ago
Change-Id: I1c794f910038459b13e16f9c3a12c44e56f142f7
This change does a few things to improve packet loss and renegotiation:
1. On outgoing RTP streams we will now properly reflect out of order
packets and packet loss in the sequence number. This allows the
remote jitterbuffer to better reorder things.
2. Video updates can now be discarded for a period of time
after one has been sent to prevent flooding of clients.
3. For declined and removed streams we will now release any
media session resources associated with them. This was not
previously done and caused an issue where old state was being
used for a new stream.
4. RTP bundling was not actually removing bundled RTP instances
from the parent. This has been resolved by removing based on
the RTP instance itself and not the SSRC.
5. The code did not properly handle explicitly unbundling an
RTP instance from its parent. This now works as expected.
ASTERISK-27143
Change-Id: Ibd91362f0e4990b6129638e712bc8adf0899fd45
This patch creates a new configuration option called "webrtc". When enabled it
defaults and enables the following options that are needed in order for webrtc
to work in Asterisk:
rtcp-mux, use_avpf, ice_support, and use_received_transport=enabled
media_encryption=dtls
dtls_verify=fingerprint
dtls_setup=actpass
When "webrtc" is enabled, this patch also parses the "msid" media level
attribute from an SDP. It will also appropriately add it onto the outgoing
session when applicable.
Lastly, when "webrtc" is enabled h264 RTCP FIR feedback frames are now sent.
ASTERISK-27119 #close
Change-Id: I5ec02e07c5d5b9ad86a34fdf31bf2f9da9aac6fd
This adds support for parsing timelen values from config files. This
includes support for all flags which apply to PARSE_INT32. Support for
this parser is added to ACO via the OPT_TIMELEN_T option type.
Fixes an issue where extra characters provided to ast_app_parse_timelen
were ignored, they now cause an error.
Testing is included.
ASTERISK-27117 #close
Change-Id: I6b333feca7e3f83b4ef5bf2636fc0fd613742554
BUNDLE is a specification used in WebRTC to allow multiple
streams to use the same underlying transport. This reduces
the number of ICE and DTLS negotiations that has to occur
to 1 normally.
This change implements this by adding support for it to
the RTP SDP module in PJSIP. BUNDLE can be turned on using
the "bundle" option and on an offer we will offer to
bundle streams together. On an answer we will accept any
bundle groups provided. Once accepted each stream is bundled
to another RTP instance for transport.
For the res_rtp_asterisk changes the ability to bundle
an RTP instance to another based on the SSRC received
from the remote side has been added. For outgoing traffic
if an RTP instance is bundled to another we will use the
other RTP instance for any transport related things. For
incoming traffic received from the transport instance we
look up the correct instance based on the SSRC and use it
for any non-transport related data.
ASTERISK-27118
Change-Id: I96c0920b9f9aca7382256484765a239017973c11
This adds a parameter to ast_waitfordigit_full which can be used to only
stop waiting when certain expected digits are received. Any unexpected
DTMF digits are simply ignored.
This also creates a new dialplan application WaitDigit.
ASTERISK-27129 #close
Change-Id: Id233935ea3d13e71c75a0861834c5936c3700ef9
This change fixes a few things uncovered during SFU testing.
1. Unreal channels incorrectly forwarded video frames when
no video stream was present on them. This caused a crash when
they were read as the core requires a stream to exist for the
underlying media type. The Unreal channel will now ensure a
stream exists for the media type before forwarding the frame
and if no stream exists then the frame is dropped.
2. Mapping of frames during bridging from the stream number of
the underlying channel to the stream number of the bridge was
done in the wrong location. This resulted in the frame getting
dropped. This mapping now occurs on reading of the frame from
the channel.
3. Bridging was using the wrong ast_read function resulting in
it living in a non-multistream world.
4. In bridge_softmix when adding new streams to existing channels
the wrong stream topology was copied resulting in no streams
being added.
Change-Id: Ib7445722c3219951d6740802a0feddf2908c18c8
This API was not actively maintained, was not added to new modules
(such as res_pjsip), and there exist better alternatives to acquire the
same information, such as the ARI.
Change-Id: I4b2185a83aeb74798b4ad43ff8f89f971096aa83
The existing auto dtmf mode reverts to inband if 4733 fails to be
negotiated. This patch adds a new mode auto_info which will
switch to INFO instead of inband if 4733 is not available.
ASTERISK-27066 #close
Change-Id: Id185b11e84afd9191a2f269e8443019047765e91
The stream topology (list of streams and order) is now stored with the
configured PJSIP endpoints and used during the negotiation process.
Media negotiation state information has been changed to be stored
in a separate object. Two of these objects exist at any one time
on a session. The active media state information is what was previously
negotiated and the pending media state information is what the
media state will become if negotiation succeeds. Streams and other
state information is stored in this object using the index (or
position) of each individual stream for easy lookup.
The ability for a media type handler to specify a callback for
writing has been added as well as the ability to add file
descriptors with a callback which is invoked when data is available
to be read on them. This allows media logic to live outside of
the chan_pjsip module.
Direct media has been changed so that only the first audio and
video stream are directly connected. In the future once the RTP
engine glue API has been updated to know about streams each individual
stream can be directly connected as appropriate.
Media negotiation itself will currently answer all the provided streams
on an offer within configured limits and on an offer will use the
topology created as a result of the disallow/allow codec lines.
If a stream has been removed or declined we will now mark it as such
within the resulting SDP.
Applications can now also request that the stream topology change.
If we are told to do so we will limit any provided formats to the ones
configured on the endpoint and send a re-invite with the new topology.
Two new configuration options have also been added to PJSIP endpoints:
max_audio_streams: determines the maximum number of audio streams to
offer/accept from an endpoint. Defaults to 1.
max_video_streams: determines the maximum number of video streams to
offer/accept from an endpoint. Defaults to 1.
ASTERISK-27076
Change-Id: I8afd8dd2eb538806a39b887af0abd046266e14c7
There have been reports of deadlocks caused by an attempt to send a frame
to a channel's rtp instance after the channel has left the native bridge
and been destroyed. This patch effectively causes the bridge channel to
keep a reference to the glue and both the audio and video rtp instances
so what gets started will get stopped.
ASTERISK-26978 #close
Reported-by: Ross Beer
Change-Id: I9e1ac49fa4af68d64826ccccd152593cf8cdb21a
In an earlier version of Asterisk a local channel [un]lock all functions were
added in order to keep a crash from occurring when a channel hung up too early
during an attended transfer. Unfortunately, when a transfer failure occurs and
depending on the timing, the local channels sometime do not get properly
unlocked and deref'ed after being locked and ref'ed. This happens because the
underlying local channel structure gets NULLed out before unlocking.
This patch reworks those [un]lock functions and makes sure the values that get
locked and ref'ed later get unlocked and deref'ed.
ASTERISK-27074 #close
Change-Id: Ice96653e29bd9d6674ed5f95feb6b448ab148b09
The SDP offer/answer model requires an answer to an offer before a new SDP
can be processed. This allows our local SDP creation to be deferred until
we know that we need to create an offer or an answer SDP. Once the local
SDP is created it won't change until the SDP negotiation is restarted.
An offer SDP in an initial SIP INVITE can receive more than one answer
SDP. In this case, we need to merge each answer SDP with our original
offer capabilities to get the currently negotiated capabilities. To
satisfy this requirement means that we cannot update our proposed
capabilities until the negotiations are restarted.
Local topology updates from ast_sdp_state_update_local_topology() are
merged together until the next offer SDP is created. These accumulated
updates are then merged with the current negotiated capabilities to create
the new proposed capabilities that the offer SDP is built.
Local topology updates are merged in several passes to attempt to be smart
about how streams from the system are matched with the previously
negotiated stream slots. To allow for T.38 support when merging, type
matching considers audio and image types to be equivalent. First streams
are matched by stream name and type. Then streams are matched by stream
type only. Any remaining unmatched existing streams are declined. Any
new active streams are either backfilled into pre-merge declined slots or
appended onto the end of the merged topology. Any excess new streams
above the maximum supported number of streams are simply discarded.
Remote topology negotiation merges depend if the topology is an offer or
answer. An offer remote topology negotiation dictates the stream slot
ordering and new streams can be added. A remote offer can do anything to
the previously negotiated streams except reduce the number of stream
slots. An answer remote topology negotiation is limited to what our offer
requested. The answer can only decline streams, pick codecs from the
offered list, or indicate the remote's stream hold state.
I had originally kept the RTP instance if the remote offer SDP changed a
stream type between audio and video since they both use RTP. However, I
later removed this support in favor of simply creating a new RTP instance
since the stream's purpose has to be changing anyway. Any RTP packets
from the old stream type might cause mischief for the bridged peer.
* Added ast_sdp_state_restart_negotiations() to restart the SDP
offer/answer negotiations. We will thus know to create a new local SDP
when it is time to create an offer or answer.
* Removed ast_sdp_state_reset(). Save the current topology before
starting T.38. To recover from T.38 simply update the local topology to
the saved topology and restart the SDP negotiations to get the offer SDP
renegotiating the previous configuration.
* Allow initial topology for ast_sdp_state_alloc() to be NULL so an
initial remote offer SDP can dictate the streams we start with. We can
always update the local topology later if it turns out we need to offer
SDP first because the remote chose to defer sending us a SDP.
* Made the ast_sdp_state_alloc() initial topology limit to max_streams,
limit to configured codecs, handle declined streams, and discard
unsupported types.
* Convert struct ast_sdp to ao2 object. Needed to easily save off a
remote SDP to refer to later for various reasons such as generating
declined m= lines in the local SDP.
* Improve converting remote SDP streams to a topology including stream
state. A stream state of AST_STREAM_STATE_REMOVED indicates the stream is
declined/dead.
* Improve merging streams to take into account the stream state.
* Added query for remote hold state.
* Added maximum streams allowed SDP config option.
* Added ability to create new streams as needed. New streams are created
with configured default audio, video, or image codecs depending on stream
type.
* Added global locally_held state along with a per stream local hold
state. Historically, Asterisk only has a global locally held state
because when the we put the remote on hold we do it for all active
streams.
* Added queries for a rejected offer and current SDP negotiation role.
The rejected query allows the using module to know how to respond to a
failed remote SDP set. Should the using module respond with a 488 Not
Acceptable Here or 500 Internal Error to the offer SDP?
* Moved sdp_state_capabilities.connection_address to ast_sdp_state. There
seems no reason to keep it in the sdp_state_capabilities struct since it
was only used by the ast_sdp_state.proposed_capabilities instance.
* Callbacks are now available to allow the using module some customization
of negotiated streams and to complete setting up streams for use. See the
typedef doxygen for each callback for what is allowable and when they are
called.
* Added topology answerer modify callback.
* Added topology pre and post apply callbacks.
* Added topology offerer modify callback.
* Added topology offerer configure callback.
* Had to rework the unit tests because I changed how SDP topologies are
merged. Replaced several unit tests with new negotiation tests.
Change-Id: If07fe6d79fbdce33968a9401d41d908385043a06
This change adds support for socket activation of certain SOCK_STREAM
listeners in Asterisk:
* AMI / AMI over TLS
* CLI
* HTTP / HTTPS
Example systemd units are provided. This support extends to any socket
which is initialized using ast_tcptls_server_start, so any unknown
modules using this function will support socket activation.
Asterisk continues to function as normal if socket activation is not
enabled or if systemd development headers are not available during
build.
ASTERISK-27063 #close
Change-Id: Id814ee6a892f4b80d018365c8ad8d89063474f4d
* changes:
SDP: Set the remote c= line in RTP instance.
SDP: Add t= line in sdp_create_from_state()
stream: Ignore declined streams for some topology calls.
This option was added to control whether to notify dialog-info state
'early' or 'confirmed' on Ringing when already INUSE.
The value "yes" is useful for some SIP phones (Cisco SPA)
to be able to indicate and pick up ringing devices.
ASTERISK-26919 #close
Change-Id: Ie050bc30023543c7dfb4365c5be3ce58c738c711
The recent change to make the use of LOAD_DECLINE more consistent
caused res_ari to unload itself before declining if the ari.conf
file wasn't found. The ari stubs though still tried to use the
configuration resulting in segfaults.
This patch creates a new CHECK_ARI_MODULE_LOADED macro which tests
to see if res_ari is actually loaded and causes the stubs to also
decline if it isn't. The macro was then added to the mustache
template's "load_module" function.
ASTERISK-27026 #close
Reported-by: Ronald Raikes
Change-Id: I263d56efa628ee3c411bdcd16d49af6260c6c91d
* Made ast_format_cap_from_stream_topology() not include any formats from
declined streams.
* Made ast_stream_topology_get_first_stream_by_type() ignore declined
streams to return the first active stream of the type.
* Updated unit tests to check these changes have the expected effect.
Change-Id: Iabbc6a3e8edf263a25fd3056c3c614407c7897df
This change adds a deferred queue to bridging. If a bridge
technology determines that a frame can not be written and
should be deferred it can indicate back to bridging to do so.
Bridging will then requeue any deferred frames upon a new
channel joining the bridge.
This change has been leveraged for T.38 request negotiate
control frames. Without the deferred queue there is a race
condition between the bridge receiving the T.38 request
negotiate and the second channel joining and being in the
bridge. If the channel is not yet in the bridge then the T.38
negotiation fails.
A unit test has also been added that confirms that a T.38
request negotiate control frame is deferred when no other
channel is in the bridge and that it is requeued when a new
channel joins the bridge.
ASTERISK-26923
Change-Id: Ie05b08523f399eae579130f4a5f562a344d2e415
When doing an attended transfer it's possible for the transferer, after
receiving an accepted response from Asterisk, to send a BYE to Asterisk,
which can then be processed before Asterisk has time to start and/or
complete the transfer process. This of course causes the transfer to not
complete successfully, thus dropping the call.
This patch makes it so any BYEs received from the transferer, after the REFER,
that initiate a session end are deferred until the transfer is complete. This
allows the channel that would have otherwise been hung up by Asterisk to
remain available throughout the transfer process.
ASTERISK-27053 #close
Change-Id: I43586db79079457d92d71f1fd993be9a3b409d5a
This introduces the ability for PJSIP code to specify filtering flags
when retrieving PJSIP contacts. The first flag for use causes the
query code to only retrieve contacts that are not unreachable. This
change has been leveraged by both the Dial() process and the
PJSIP_DIAL_CONTACTS dialplan function so they will now only attempt
calls to contacts which are not unreachable.
ASTERISK-26281
Change-Id: I8233b4faa21ba3db114f5a42e946e4b191446f6c
In review 4843 (ASTERISK-24858), we added a hack that forced a smoother
creation when sending signed linear so that the byte order was adjusted
during transmission. This was needed because smoother flags were lost
during the new format work that was done in Asterisk 13.
Rather than rolling that same hack into res_rtp_multicast, re-introduce
smoother flags so that formats can dictate their own options.
Change-Id: I77b835fba0e539c6ce50014a984766f63cab2c16
A previous commit added plumbing to bridge_softmix to allow for an SFU
experience with Asterisk. This commit adds an option to app_confbridge
that allows for a confbridge to actually make use of the SFU video mode.
SFU mode is implemented in a "set it and forget it" kind of way. That
is, when the bridge is created, if SFU mode is enabled, then the video
mode gets set to SFU and cannot be changed. Future improvements may
allow for a hybrid experience (e.g. forward multiple video streams,
specifically those of the most recent talkers), but for this addition,
no such capability is present.
Change-Id: I87bbcb63dec6dbbb42488f894871b86f112b2020
This sets up the "plumbing" in bridge_softmix to
be able to accommodate Asterisk asking as an SFU
(selective forwarding unit) for conferences.
The way this works is that whenever a channel enters or leaves a
conference, all participants in the bridge get sent a stream topology
change request. The topologies consist of the channels' original
topology, along with video destination streams corresponding to each
participants' source video streams. So for instance, if Alice, Bob, and
Carol are in the conference, and each supplies one video stream, then
the topologies for each would look like so:
Alice:
Audio,
Source video(Alice),
Destination Video(Bob),
Destination video (Carol)
Bob:
Audio,
Source video(Bob)
Destination Video(Alice),
Destination video (Carol)
Carol:
Audio,
Source video(Carol)
Destination Video(Alice),
Destination video (Bob)
This way, video that arrives from a source video stream can then be
copied out to the destination video streams on the other participants'
channels.
Once the bridge gets told that a topology on a channel has changed, the
bridge constructs a map in order to get the video frames routed to the
proper destination streams. This is done using the bridge channel's
stream_map.
This change is bare-bones with regards to SFU support. Some key features
are missing at this point:
* Stream limits. This commit makes no effort to limit the number of
streams on a specific channel. This means that if there were 50 video
callers in a conference, bridge_softmix will happily send out topology
change requests to every channel in the bridge, requesting 50+
streams.
* Configuration. The plumbing has been added to bridge_softmix, but
there has been nothing added as of yet to app_confbridge to enable SFU
video mode.
* Testing. Some functions included here have unit tests.
However, the functionality as a whole has only been verified by
hand-tracing the code.
* Selectivenss. For a "selective" forwarding unit, this does not
currently have any means of being selective.
* Features. Presumably, someone might wish to only receive video from
specific sources. There are no external-facing functions at the moment
that allow for users to select who they receive video from.
* Efficiency. The current scheme treats all video streams as being
unidirectional. We could be re-using a source video stream as a
desetnation, too. But to simplify things on this first round, I did it
this way.
Change-Id: I7c44a829cc63acf8b596a337b2dc3c13898a6c4d
...that can only be run by explicitly calling it with
'test execute category /DO_NOT_RUN/ name RAISE_SEGV'
This allows us to more easily test CI and debugging tools that
should do certain things when asterisk coredumps.
To allow this a new member was added to the ast_test_info
structure named 'explicit_only'. If set by a test, the test
will be skipped during a 'test execute all' or
'test execute category ...'.
Change-Id: Ia3a11856aae4887df9a02b6b081cc777b36eb6ed
Added functions that convert a string to an unsigned integer or unsigned long.
A couple of unit test were also created to test the routines. The reasons for
adding these conversion utilities (and hopefully eventually more) are as
follows:
* Conversion routines are functionally contained with consistent and
better error checking
* The function names offer a better description of what is happening
* It encourages code reuse for easier bug fixing at a single source
* It's simpler to use
* It's unit testable
For instance, currently in a lot of places when converting to an integer or
similar the "sscanf" function is used. When using "sscanf" it may not be
immediately clear what's happening as it lacks semantic naming. Limited error
checking is usually done as well. For example, most of the time a check is done
to make sure the value converted, but does not check for overflows or negative
valued conversions when converting unsigned numbers.
Why use/wrap "strtoul" and not "sscanf" then? Primarily, it lacks some of the
built in error handling that "strtoul" has. For instance "strtoul" contains
overflow checks. Less so, but can still factor as reasons, "sscanf" is slightly
more complex in its use. And maybe a bit controversial, but it may be ("big if")
potentially slower than "strtoul" in some cases.
Change-Id: If7eaca4a48f8c7b89cc8b5a1f4bed2852fca82bb
When manipulating flags on a channel the channel has to be
locked to guarantee that nothing else is also manipulating
the flags. This change introduces locking where necessary to
guarantee this. It also adds helper functions that manipulate
channel flags and lock to reduce repeated code.
ASTERISK-26789
Change-Id: I489280662dba0f4c50981bfc5b5a7073fef2db10
* changes:
SDP: Make process possible multiple fmtp attributes per rtpmap.
SDP: Explicitly stop a RTP instance before destoying it.
SDP: Rework merge_capabilities().
SDP: Update ast_get_topology_from_sdp() to keep RTP map.
This option was added to turn off notifying the progress details
on Blind Transfer. If this option is not set then the chan_pjsip
will send NOTIFY "200 OK" immediately after "202 Accepted".
Some SIP phones like Mitel/Aastra or Snom keep the line busy until
receive "200 OK".
ASTERISK-26333 #close
Change-Id: Id606fbff2e02e967c02138457badc399144720f2
When we optionally set the interface_address we are forcing the media to
go out a specific interface address. This allows us to optionally have
the media go out the interface that SIP signalling came in on or if we are
configured to have the media always go out a specific address.
Change-Id: I160d9fac322a075bd2557b430632544178196189
* Made sdp_add_m_from_rtp_stream() and sdp_add_m_from_udptl_stream()
handle generating disabled/declined streams.
* Added /main/sdp/sdp_merge_asymmetric unit test. It currently does not
check the offerer side negotiated SDP because that isn't the purpose of
this patch and there is much to be done to handle declined/dummy streams.
* Added T.38 image streams to the /main/sdp/sdp_merge_symmetric and
/main/sdp/sdp_merge_crisscross unit tests.
Change-Id: Ib4dcb3ca4f9a9133b376f4e3302f9a1f963f2b31
All log messages go to a queue serviced by a single thread
which does all the IO. This setting controls how big that
queue can get (and therefore how much memory is allocated)
before new messages are discarded. The default is 1000.
Should something go bezerk and log tons of messages in a tight
loop, this will prevent memory escalation.
When the limit is reached, a WARNING is logged to that effect
and messages are discarded until the queue is empty again. At
that time another WARNING will be logged with the count of
discarded messages. There's no "low water mark" for this queue
because the logger thread empties the entire queue and processes it
in 1 batch before going back and waiting on the queue again.
Implementing a low water mark would mean additional locking as
the thread processes each message and it's not worth it.
A "test" was added to test_logger.c but since the outcome is
non-deterministic, it's really just a cli command, not a unit
test.
Change-Id: Ib4520c95e1ca5325dbf584c7989ce391649836d1
ast_stream_clone() cannot copy the opaque user data stored on a stream.
We don't know how to clone the data so it isn't copied into the clone.
Change-Id: Ia51321bf38ecbfdcc53787ca77ea5fd2cabdf367
When using the Bridge AMI action on the same channel multiple times
it was possible for the channel to return to the wrong location in
the dialplan if the other party hung up. This happened because the
priority of the channel was not preserved across each action
invocation and it would fail to move on to the next priority in
other cases.
This change makes it so that the priority of a channel is preserved
when taking control of it from another thread and it is incremented
as appropriate such that the priority reflects where the channel
should next be executed in the dialplan, not where it may or may not
currently be.
The Bridge AMI action was also changed to ensure that it too
starts the channels at the next location in the dialplan.
ASTERISK-24529
Change-Id: I52406669cf64208aef7252a65b63ade31fbf7a5a
This patch is the first cut at adding stream support to the bridging framework.
Changes were made to the framework that allows mapping of stream topologies to
a bridge's supported media types.
The first channel to enter a bridge initially defines the media types for a
bridge (i.e. a one to one mapping is created between the bridge and the first
channel). Subsequently added channels merge their media types into the bridge's
adding to it when necessary. This allows channels with different sized
topologies to map correctly to each other according to media type. The bridge
drops any frame that does not have a matching index into a given write stream.
For now though, bridge_simple will align its two channels according to size or
first to join. Once both channels join the bridge the one with the most streams
will indicate to the other channel to update its streams to be the same as that
of the other. If both channels have the same number of streams then the first
channel to join is chosen as the stream base.
A topology change source was also added to a channel when a stream toplogy
change request is made. This allows subsystems to know whether or not they
initiated a change request. Thus avoiding potential recursive situations.
ASTERISK-26966 #close
Change-Id: I1eb5987921dd80c3cdcf52accc136393ca2d4163
The telephone_event option was used as a flag and a bit mapped value in
different places when it is a boolean. It is also inadequate to configure
the DTMF operation of the RTP instance created for the stream.
Change-Id: Ib1addeaf0ce86f07039f2f979cab29405dc5239b
RFC 5576 defines how SSRC-level attributes may be added to SDP media
descriptions. In general, this is useful for grouping related SSRCes,
indicating SSRC-level format attributes, and resolving collisions in RTP
SSRC values. These attributes are used widely by browsers during WebRTC
communications, including attributes defined by documents outside of RFC
5576.
This commit introduces the addition of SSRC-level attributes into SDPs
generated by Asterisk. Since Asterisk does not tend to use multiple
SSRCs on a media stream, the initial support is minimal. Asterisk
includes an SSRC-level CNAME attribute if configured to do so. This at
least gives browsers (and possibly others) the ability to resolve SSRC
collisions at offer-answer time.
In order to facilitate this, the RTP engine API has been enhanced to be
able to retrieve the SSRC and CNAME on a given RTP instance.
res_rtp_asterisk currently does not provide meaningful CNAME values in
its RTCP SDES items, and therefore it currently will always return an
empty string as the CNAME value. A task in the near future will result
in res_rtp_asterisk generating more meaningful CNAMEs.
Change-Id: I29e7f23e7db77524f82a3b6e8531b1195ff57789
If you use ast_request to create a PJSIP channel but then hang it
up without causing a transaction to be sent, the session will
never be destroyed. This is due ot the fact that it's pjproject
that triggers the session cleanup when the transaction ends.
app_chanisavail was doing this to get more granular channel state
and it's also possible for this to happen via ARI.
* ast_sip_session_terminate was modified to explicitly call the
cleanup tasks and unreference session if the invite state is NULL
AND invite_tsx is NULL (meaning we never sent a transaction).
* chan_pjsip/hangup was modified to bump session before it calls
ast_sip_session_terminate to insure that session stays valid
while it does its own cleanup.
* Added test events to session_destructor for a future testsuite
test.
ASTERISK-26908 #close
Reported-by: Richard Mudgett
Change-Id: I52daf6f757184e5544c261f64f6fe9602c4680a9
This change extends the ast_request functionality by adding another
function and callback to create an outgoing channel with a requested
stream topology. Fallback is provided by either converting the
requested stream topology into a format capabilities structure if
the channel driver does not support streams or by converting the
requested format capabilities into a stream topology if the channel
driver does support streams.
The Dial application has also been updated to request an outgoing
channel with the stream topology of the calling channel.
ASTERISK-26959
Change-Id: Ifa9037a672ac21d42dd7125aa09816dc879a70e6
Added an pre-defined integer vector declaration. This makes integer vectors
easier to declare and pass around. Also, added the ability to default a vector
up to a given size with a default value. Lastly, added functionality that
returns the "nth" index of a matching value.
Also, updated a unit test to test these changes.
Change-Id: Iaf4b51b2540eda57cb43f67aa59cf1d96cdbcaa5
This change adds a T.38 format which can be used in a stream
topology to specify that a UDPTL stream needs to be created.
The SDP API has been changed to understand T.38 and create
the UDPTL session, add the attributes, and parse the attributes.
This change does not change the boundary of the T.38 state
machine. It is still up to the channel driver to implement and
act on it (such as queueing control frames or reacting to them).
ASTERISK-26949
Change-Id: If28956762ccb8ead562ac6c03d162d3d6014f2c7
The gist of this work ensures that when a remote SDP is received, it is
merged properly with the local capabilities. The remote SDP is converted
into a stream topology. That topology is then merged with the current
local topology on the SDP state. That new merged topology is then used
to create an SDP. Finally, adjustments are made to RTP instances based
on knowledge gained from the remote SDP.
There are also a battery of tests in this commit that ensure that some
basic SDP merges work as expected.
While this may not sound like a big change, it has the property that it
caused lots of ancillary changes.
* The remote SDP is no longer stored on the SDP state. Biggest reason:
there's no need for it. The remote SDP is used at the time it is being
set and nowhere else.
* Some new SDP APIs were added in order to find attributes and convert
generic SDP attributes into rtpmap structures.
* Writing tests made me realize that retrieving a value from an SDP
options structure, the SDP options needs to be made const.
* The SDP state machine was essentially gutted by a previous commit.
Initially, I attempted to reinstate it, but I found that as it had
been defined, it was not all that useful. What was more useful was
knowing the role we play in SDP negotiation, so the SDP state machine
has been transformed into an indicator of role.
* Rather than storing separate local and joint stream state
capabilities, it makes more sense to keep track of current stream
state and update it as things change.
Change-Id: I5938c2be3c6f0a003aa88a39a59e0880f8b2df3d
The primary win of switching to eventfd when possible is that it only
uses a single file descriptor while pipe() will use two. This means for
each bridge channel we're reducing the number of required file
descriptors by 1, and - if you're using timerfd - we also now have 1
less file descriptor per Asterisk channel.
The API is not ideal (passing int arrays), but this is the cleanest
approach I could come up with to maintain API/ABI.
I've also removed what I believe to be an erroneous code block that
checked the non-blocking flag on the pipe ends for each read. If the
file descriptor is 'losing' its non-blocking mode, it is because of a
bug somewhere else in our code.
In my testing I haven't seen any measurable difference in performance.
Change-Id: Iff0fb1573e7f7a187d5211ddc60aa8f3da3edb1d
This saves around 100 bytes when G.711, G.722, G.729, and GSM are advertised in
SDP. This reduces the chance to hit the MTU bearer of 1300 bytes for SIP over
UDP, if many codecs are allowed in Asterisk. This new feature is enabled
together with the optional feature compact_headers=yes via the file pjsip.conf.
ASTERISK-26932 #close
Change-Id: Iaa556ab4c8325cd34c334387ab2847fab07b1689
In all non-pbx modules, AST_MODULE_LOAD_FAILURE has been changed
to AST_MODULE_LOAD_DECLINE. This prevents asterisk from exiting
if a module can't be loaded. If the user wishes to retain the
FAILURE behavior for a specific module, they can use the "require"
or "preload-require" keyword in modules.conf.
A new API was added to logger: ast_is_logger_initialized(). This
allows asterisk.c/check_init() to print to the error log once the
logger subsystem is ready instead of just to stdout. If something
does fail before the logger is initialized, we now print to stderr
instead of stdout.
Change-Id: I5f4b50623d9b5a6cb7c5624a8c5c1274c13b2b25
On 2's compliment machines abs(INT_MIN) behavior is undefined and
results in a negative value still being returnd. This results in
negative hash codes that can result in crashes.
ASTERISK-26528 #close
Change-Id: Idff550145ca2133792a61a2e212b4a3e82c6517b
0035-r5572-svn-backport-dialog-transaction-deadlock.patch
0036-r5573-svn-backport-ua-pjsua-transaction-deadlock.patch
0037-r5576-svn-backport-session-timer-crash.patch
Also removed the progress bar from wget download to stdout.
ASTERISK-26905 #close
Reported-by: Ross Beer
Change-Id: I268fb3cf71a3bb24283ff0d24bd8b03239d81256
* Report failures if configure finds a required header is missing.
* Deduplicate includes between asterisk.h, astmm.h and compat.h.
* Unconditionally include headers in compat.h if required elsewhere.
Change-Id: Ie67d0185ca71fbfb81c9bdfaebe46a49e3c56dc5
The ast_json structure is used in many Asterisk headers and is often the
only part of json.h used. This adds a forward declaration to asterisk.h
and removes the include of json.h from many headers. The declaration
has been left in endpoints.h and stasis.h to avoid problems with source
files that use ast_json functions without directly including json.h.
ari.h continues to include json.h as it uses enum
ast_json_encoding_format.
Change-Id: Id766aabce6bed56626d27e8d29f559b5e687b769
This change cleans up state management for media streams by moving
RTP instances into their own session structure and adding additional
details that are not relevant to the core (such as connection address).
These can live either in the local capabilities or joint capabilities.
The ability to set explicit connection address information for
the purposes of direct media and NAT has also been added at the
global and stream specific level.
ASTERISK-26900
Change-Id: If7e5307239a9534420732de11c451a2705b6b681
The ao2_global_obj_release() function holds an exclusive lock on the
global object while it is being dereferenced. Any destructors that
run during this time that call ao2_global_obj_ref() will deadlock
because a read lock is required.
Instead, we make the global object inaccessible inside of the write
lock and only dereference it once we have released the lock. This
allows the affected destructors to fail gracefully.
While this doesn't completely solve the referenced issue (the error
message about not being able to create an IQ continues to be shown)
it does solve the backtrace spew that accompanied it.
ASTERISK-21009 #close
Reported by: Marcello Ceschia
Change-Id: Idf40ae136b5070dba22cb576ea8414fbc9939385
This change removes the old epoll support which has not been used or
maintained in quite some time.
The fixed number of file descriptors on a channel has also been removed.
File descriptors are now contained in a growable vector. This can be
used like before by specifying a specific position to store a file
descriptor at or using a new API call, ast_channel_fd_add, which adds
a file descriptor to the channel and returns its position.
Tests have been added which cover the growing behavior of the vector
and the new API call.
ASTERISK-26885
Change-Id: I1a754b506c009b83dfdeeb08c2d2815db30ef928
Updated the AMI version for the following reason (see CHANGES for more details):
The 'PJSIPShowEndpoint' command's response event of 'IdentifyDetail' now
contains a new optional parameter, 'MatchHeader'.
Change-Id: Ie206913ef1dcfa6a2ebe3282da2387e52d6f05b9
Dynamic payload types were statically defined in Asterisk. This unfortunately
limited the number of dynamic payloads that could be registered. With this patch
dynamic payload type numbers are now assigned dynamically and per RTP instance.
However, in order to limit any issues where some clients expect the old
statically defined value this patch makes it so the value Asterisk used to pre-
designate is used for the dynamic assignment if available.
An option, "rtp_use_dynamic", has also been added (can be set in asterisk.conf)
that turns the new dynamic behavior on or off. When off it reverts back to using
statically defined payload values. This option defaults to "yes" in Asterisk 15.
ASTERISK-26515 #close
patches:
ASTERISK-26515.diff submitted by jcolp (license 5000
Change-Id: I7653465c5ebeaf968f1a1cc8f3f4f5c4321da7fc
Support for RFC3578 overlap dialling (i.e. 484 Response to partially matched
destinations) as currently provided by chan_sip is missing from res_pjsip.
This patch adds a new endpoint attribute (allow_overlap) [defaults to yes]
which when set to yes enables 484 responses to partial destination
matches rather than the current 404.
ASTERISK-26864
Change-Id: Iea444da3ee7c7d4f1fde1d01d138a3d7b0fe40f6
Rather than hard-coding UDP, allow consumers of the HEP API to specify
which protocol is in use. Update the PJSIP provider to pass in the
current protocol type.
ASTERISK-26850 #close
Change-Id: I54bbb0a001cfe4c6a87ad4b6f2014af233349978
POSIX does not require getprotobyname() to be thread safe and some
implementations use static memory which causes issues when multiple
threads are used.
Further, our usage of it today is just to ultimately get IPPROTO_TCP
for calls to setsockopt(). So instead we just use IPPROTO_TCP directly.
Change-Id: I2e14e58674808f7ce99b2f5e900d0f90d0d8da48
A new transport parameter 'symmetric_transport' has been added.
When a request from a dynamic contact comes in on a transport with
this option set to 'yes', the transport name will be saved and used
for subsequent outgoing requests like OPTIONS, NOTIFY and INVITE.
It's saved as a contact uri parameter named 'x-ast-txp' and will
display with the contact uri in CLI, AMI, and ARI output. On the
outgoing request, if a transport wasn't explicitly set on the
endpoint AND the request URI is not a hostname, the saved transport
will be used and the 'x-ast-txp' parameter stripped from the
outgoing packet.
* config_transport was modified to accept and store the new parameter.
* config_transport/transport_apply was updated to store the transport
name in the pjsip_transport->info field using the pjsip_transport->pool
on UDP transports.
* A 'multihomed_on_rx_message' function was added to
pjsip_message_ip_updater that, for incoming requests, retrieves the
transport name from pjsip_transport->info and retrieves the transport.
If transport->symmetric_transport is set, an 'x-ast-txp' uri parameter
containing the transport name is added to the incoming Contact header.
* An 'ast_sip_get_transport_name' function was added to res_pjsip.
It takes an ast_sip_endpoint and a pjsip_sip_uri and returns a
transport name if endpoint->transport is set or if there's an
'x-ast-txp' parameter on the uri and the uri host is an ipv4 or
ipv6 address. Otherwise it returns NULL.
* An 'ast_sip_dlg_set_transport' function was added to res_pjsip
which takes an ast_sip_endpoint, a pjsip_dialog, and an optional
pjsip_tpselector. It calls ast_sip_get_transport_name() and if
a non-NULL is returned, sets the selector and sets the transport
on the dialog. If a selector was passed in, it's updated.
* res_pjsip/ast_sip_create_dialog_uac and ast_sip_create_dialog_uas
were modified to call ast_sip_dlg_set_transport() instead of their
original logic.
* res_pjsip/create_out_of_dialog_request was modified to call
ast_sip_get_transport_name() and pjsip_tx_data_set_transport()
instead of its original logic.
* Existing transport logic was removed from endpt_send_request
since that can only be called after a create_out_of_dialog_request.
* res_pjsip/ast_sip_create_rdata was converted to a wrapper around
a new 'ast_sip_create_rdata_with_contact' function which allows
a contact_uri to be specified in addition to the existing
parameters. (See below)
* res_pjsip_pubsub/internal_pjsip_evsub_send_request was eliminated
since all it did was transport selection and that is now done in
ast_sip_create_dialog_uac and ast_sip_create_dialog_uas.
* 'contact_uri' was added to subscription_persistence. This was
necessary because although the parsed rdata contact header has the
x-ast-txp parameter added (if appropriate),
subscription_persistence_update stores the raw packet which
doesn't have it. subscription_persistence_recreate was then
updated to call ast_sip_create_rdata_with_contact with the
persisted contact_uri so the recreated subscription has the
correct transport info to send the NOTIFYs.
* res_pjsip_session/internal_pjsip_inv_send_msg was eliminated since
all it did was transport selection and that is now done in
ast_sip_create_dialog_uac.
* pjsip_message_ip_updater/multihomed_on_tx_message was updated
to remove all traces of the x-ast-txp parameter from the
outgoing headers.
NOTE: This change does NOT modify the behavior of permanent
contacts specified on an aor. To do so would require that the
permanent contact's contact uri be updated with the x-ast-txp
parameter and the aor sorcery object updated. If we need to
persue this, we need to think about cloning permanent contacts into
the same store as the dynamic ones on an aor load so they can be
updated without disturbing the originally configured value.
You CAN add the x-ast-txp parameter to a permanent contact's uri
but it would be much simpler to just set endpoint->transport.
Change-Id: I4ee1f51473da32ca54b877cd158523efcef9655f
Dereferencing struct ast_autochan.chan without first calling
ast_autochan_channel_lock() is unsafe because the pointer could change at
any time due to a masquerade. Unfortunately, ast_autochan_channel_lock()
itself uses struct ast_autochan.chan unsafely and can result in a deadlock
if the original channel happens to get destroyed after a masquerade in
addition to the pointer getting changed.
The problem is more likely to happen with v11 and earlier because
masquerades are used to optimize out local channels on those versions.
However, it could still happen on newer versions if the channel is
executing a dialplan application when the channel is transferred or
redirected. In this situation a masquerade still must be used.
* Added a lock to struct ast_autochan to safely be able to use
ast_autochan.chan while trying to get the channel lock in
ast_autochan_channel_lock(). The locking order is the channel lock then
the autochan lock. Locking in the other direction requires deadlock
avoidance.
* Fix unsafe ast_autochan.chan usages in app_mixmonitor.c.
* Fix unsafe ast_autochan.chan usages in app_chanspy.c.
* app_chanspy.c: Removed unused autochan parameter from next_channel().
ASTERISK-26867
Change-Id: Id29dd22bc0f369b44e23ca423d2f3657187cc592
This commit adds support for RFC 5761: Multiplexing RTP Data and Control
Packets on a Single Port. Specifically, it enables the feature when
using chan_pjsip.
A new option, "rtcp_mux" has been added to endpoint configuration in
pjsip.conf. If set, then Asterisk will attempt to use rtcp-mux with
whatever it communicates with. Asterisk follows the rules set forth in
RFC 5761 with regards to falling back to standard RTCP behavior if the
far end does not indicate support for rtcp-mux.
The lion's share of the changes in this commit are in
res_rtp_asterisk.c. This is because it was pretty much hard wired to
have an RTP and an RTCP transport. The strategy used here is that when
rtcp-mux is enabled, the current RTCP transport and its trappings (such
as DTLS SSL session) are freed, and the RTCP session instead just
mooches off the RTP session. This leads to a lot of specialized if
statements throughout.
ASTERISK-26732 #close
Reported by Dan Jenkins
Change-Id: If46a93ba1282418d2803e3fd7869374da8b77ab5
* Added additional fields to ast_sdp_options.
* Re-organized ast_sdp.
* Updated field names to correspond to RFC4566 terminology.
* Created allocs/frees for SDP children.
* Created getters/setters for SDP children where appropriate.
* Added ast_sdp_create_from_state.
* Refactored res_sdp_translator_pjmedia for changes.
Change-Id: Iefbd877af7f5a4d3c74deead1bff8802661b0d48
This change adds a few things to facilitate stream topology changing:
1. Control frame types have been added for use by the channel driver
to notify the application that the channel wants to change the stream
topology or that a stream topology change has been accepted. They are
also used by the indicate interface to the channel that the application
uses to indicate it wants to do the same.
2. Legacy behavior has been adopted in ast_read() such that if a
channel requests a stream topology change it is denied automatically
and the current stream topology is preserved if the application is
not capable of handling streams.
Tests have also been written which confirm the multistream and
non-multistream behavior.
ASTERISK-26839
Change-Id: Ia68ef22bca8e8457265ca4f0f9de600cbcc10bc9
* Removed the AST_CHAN_TP_MULTISTREAM tech property. We now rely
on read_stream being set to indicate a multi stream channel.
* Added ast_channel_is_multistream convenience function.
* Fixed issue where stream and default_stream weren't being set on
a frame retrieved from the queue.
* Now testing for NULL being returned from the driver's read or
read_stream callback.
* Fixed issue where the dropnondefault code was crashing on a
NULL f.
* Now enforcing that if either read_stream or write_stream are
set when ast_channel_tech_set is called that BOTH are set.
* Added the unit tests.
ASTERISK-26816
Change-Id: If7792b20d782e71e823dabd3124572cf0a4caab2
This introduces and documents the various states in the state machine.
This also introduces API functions that induce state changes, and places
TODO comments telling what needs to be done in addition to what is
already there. Those TODOs will be replaced with real code in upcoming
changes.
Change-Id: I871c0eb480b4c84d83e91ac5628e7a673e8b89ed
The bridge_native_rtp module did not properly handle the case where
a smart bridge operation occurs while a channel is suspended. In this
scenario the module would incorrectly set up local or remote RTP
bridging despite the media having to flow through Asterisk. The remote
endpoint would see two media streams and experience wonky audio.
The module has been changed so that it ensures both channels are
not suspended when performing the native RTP bridging and this
requirement has been documented in the bridge technology.
ASTERISK-26781
Change-Id: Id4022d73ace837d4a293106445e3ade10dbc7c7c
This change introduces an ast_read_stream function and callback in
the channel technology which allows reading frames from all streams
and not just the default streams.
The stream number has also been added to frames. This is to allow the
case where frames are queued onto the channel instead of being read
directly from the driver.
This change does impose a restriction on reading though: a chain of
frames can only contain frames from the same stream.
ASTERISK-26816
Change-Id: I5d7dc35e86694df91fd025126f6cfe0453aa38ce
This change adds an ast_write_stream function which allows
writing a frame to a specific media stream. It also moves
ast_write() to using this underneath by writing media
frames provided to it to the default streams of the channel.
Existing functionality (such as audiohooks, framehooks, etc)
are limited to being applied to the default stream only.
Unit tests have also been added which test the behavior of
both non-multistream and multistream channels to confirm that
the write() and write_stream() callbacks are invoked
appropriately.
ASTERISK-26793
Change-Id: I4df20d1b65bd4d787fce0b4b478e19d2dfea245c
Adds binaural synthesis to bridge_softmix (via convolution using libfftw3).
Binaural synthesis is conducted at 48kHz.
For a conference, only one spatial representation is rendered.
The default rendering is applied for mono-capable channels.
ASTERISK-26292
Change-Id: Iecdb381b6adc17c961049658678f6219adae1ddf
The "core show channel" CLI command will now output the streams
present on the channel with their details.
ASTERISK-26811
Change-Id: I9c95b57aa09415005f0677a1949a0feb07e4987a
George Joseph
Walter Doekes
Corey Farrell
Torrey Searle
Richard Mudgett
Kevin Harwell
Joshua Colp
Jenkins2
Matthew Fredrickson
Sean Bright
Mark Michelson
Alexei Gradinari
zuul
Alexander Traud
Richard Begg
frahaase