\subsubsection{Introduction}

Asterisk can set the Type of Service (TOS) byte on outgoing IP packets
for various protocols.  The TOS byte is used by the network to provide
some level of Quality of Service (QoS) even if the network is
congested with other traffic. 

Also asterisk running on Linux can set 802.1p CoS marks in VLAN packets 
for all used VoIP protocols. It is useful when you are working in switched 
enviropment. For maping skb->priority and VLAN CoS mark you need to use 
command "vconfig set_egress_map [vlan-device] [skb-priority] [vlan-qos]".

\subsubsection{SIP}

In sip.conf, there are three parameters that control the TOS settings:
"tos\_sip", "tos\_audio" and "tos\_video". tos\_sip controls what TOS SIP 
call signalling packets are set to.  tos\_audio controls what TOS RTP audio
packets are set to.  tos\_video controls what TOS RTP video packets are
set to.  

There are four parameters to control 802.1p CoS: "cos\_sip", "cos\_audio", 
"cos\_video" and "cos\_text". It's behavior the same as writen above.

There is a "tos" parameter that is supported for backwards
compatibility.  The tos parameter should be avoided in sip.conf
because it sets all three tos settings in sip.conf to the same value.

\subsubsection{IAX2}
In iax.conf, there is a "tos" parameter that sets the global default TOS
for IAX packets generated by chan\_iax2.  Since IAX connections combine
signalling, audio, and video into one UDP stream, it is not possible
to set the TOS separately for the different types of traffic.

In iaxprov.conf, there is a "tos" parameter that tells the IAXy what TOS
to set on packets it generates.  As with the parameter in iax.conf,
IAX packets generated by an IAXy cannot have different TOS settings
based upon the type of packet.  However different IAXy devices can
have different TOS settings.

\subsubsection{H.323}
Also support TOS and CoS. 

\subsubsection{MGCP}
Also support TOS and CoS.

\subsubsection{IP TOS values}

The allowable values for any of the tos* parameters are:
CS0, CS1, CS2, CS3, CS4, CS5, CS6, CS7, AF11, AF12, AF13,
AF21, AF22, AF23, AF31, AF32, AF33, AF41, AF42, AF43 and
ef (expedited forwarding),

The tos* parameters also take numeric values.

The lowdelay, throughput, reliability, mincost, and none values are
deprecated because they set the IP TOS using the outdated "IP
precedence" model as defined in RFC 791 and RFC 1349. They still
work in this version of Asterisk, but will be removed in future releases.

\subsubsection{802.1p CoS values}

As 802.1p uses 3 bites from VLAN header, there are parameter can take 
integer values from 0 to 7.


\begin{verbatim}
===========================================
Configuration	Parameter	Recommended
File				Setting
-------------------------------------------
sip.conf	tos\_sip	cs3
sip.conf	tos\_audio	ef
sip.conf	tos\_video	af41
sip.conf	tos\_text	af41
sip.conf	cos\_sip	4
sip.conf	cos\_audio	6
sip.conf	cos\_video	5
sip.conf	cos\_text	0
-------------------------------------------
iax.conf	tos		ef
iax.conf	cos		6	
-------------------------------------------
iaxprov.conf	tos		ef
-------------------------------------------
mgcp.conf	tos		ef
mgcp.conf	cos		6
-------------------------------------------
h323.conf	tos		ef
h323.conf	cos		6
===========================================
\end{verbatim}

\subsubsection{Reference}

IEEE 802.1Q Standard:
http://standards.ieee.org/getieee802/download/802.1Q-1998.pdf
Related protocols: IEEE 802.3, 802.2, 802.1D, 802.1Q

RFC 2474 - "Definition of the Differentiated Services Field
(DS field) in the IPv4 and IPv6 Headers", Nichols, K., et al,
December 1998.

IANA Assignments, DSCP registry
Differentiated Services Field Codepoints
http://www.iana.org/assignments/dscp-registry

To get the most out of setting the TOS on packets generated by
Asterisk, you will need to ensure that your network handles packets
with a TOS properly.  For Cisco devices, see the previously mentioned
"Enterprise QoS Solution Reference Network Design Guide".  For Linux
systems see the "Linux Advanced Routing \& Traffic Control HOWTO" at
<http://www.lartc.org/>.

For more information on Quality of
Service for VoIP networks see the "Enterprise QoS Solution Reference
Network Design Guide" version 3.3 from Cisco at:

<http://www.cisco.com/application/pdf/en/us/guest/netsol/ns432/c649/ccmigration\_09186a008049b062.pdf>

