Some SBCs require responses to empty SIP INFO packets
after establishing call via INVITE, if not responded to
they may drop your call after unspecified timeout of X minutes.
They are identified by having no Content-Type, check for this
and respond with 200 - OK message.
ASTERISK-24986 #close
Reported-by: Ilya Trikoz, Federico Santulli
Change-Id: Ib27e4f07151e5aef28fa587e4ead36c5b87c43e0
Nothing was cleaning up the registration state object when ast_sorcery_delete
was called on a registration. So, the registration was deleted from sorcery
but the state object went right on refreshing the registration (or failing
to refresh the registration) with the peer.
* Added a 'deleted' observer on registration that removes the state object.
ASTERISK-25964 #close
Reported-by Matt Jordan
Change-Id: I2db792145cdb1f72ebbf57dd9099596dbbf12c23
Although it's perfectly legal to place multiple SIP messages in the same packet,
it can cause problems because the Linux default is to enable Path MTU Discovery
which sets the Don't Fragment bit on the packets. If adding a second message to
the packet causes the MTU to be exceeded, and the destination isn't equipped to
send a FRAGMENTATION NEEDED response to a large packet, the packet will just be
dropped.
We can't specifically tell the stack to send only 1 message per packet, but we
can turn on TCP_NODELAY when we create the transport. This will at least tell
the stack to send packets as soon as possible.
ASTERISK-26005 #close
Reported-by: Ross Beer
Change-Id: I820f23227183f2416ca5e393bec510e8fe1c8fbd
When bound to an 'any' address, e.g., 0.0.0.0, PJSIP reports as its
local address the 'any' address, as opposed to the IP address we
actually received the packet on. This can cause some confusion in Homer,
as it will dutifully report what we send it.
This patch uses the PJSIP inspection routines to determine which IP
address we probably received the packet on based on the remote party's
IP address. In the event that this fails, it falls back to the IP
address natively reported by the transport.
Change-Id: I076f835d2aef489e1ee1d01595b211eb2ce62da3
The Location headers returned by:
* /bridges/{bridgeId}/play
* /bridges/{bridgeId}/record
* /channels/{channelId}/play
* /channels/{channelId}/record
Did not have the '/ari' prefix, and in the case of the 'play' resources, were
using 'playback' instead of 'playbacks.'
Change-Id: I957c58a3a1471bf477dae7c67faa1b74fcd9241c
With the old SIP module we can use IP access controls per peer.
PJSIP module missing this feature.
This patch added next configuration Endpoint options:
"acl" - list of IP ACL section names in acl.conf
"deny" - List of IP addresses to deny access from
"permit" - List of IP addresses to permit access from
"contact_acl" - List of Contact ACL section names in acl.conf
"contact_deny" - List of Contact header addresses to deny
"contact_permit" - List of Contact header addresses to permit
This patch also better logging failed request:
add custom message instead of "No matching endpoint found"
add SIP method to logging
ASTERISK-25900
Change-Id: I456dea3909d929d413864fb347d28578415ebf02
At one point in time, it seemed like a good idea to use the Asterisk
channel name as the HEP correlation UUID. In particular, it felt like
this would be a useful identifier to tie PJSIP messages and RTCP
messages together, along with whatever other data we may eventually send
to Homer. This also had the benefit of keeping the correlation UUID
channel technology agnostic.
In practice, it isn't as useful as hoped, for two reasons:
1) The first INVITE request received doesn't have a channel. As a
result, there is always an 'odd message out', leading it to be
potentially uncorrelated in Homer.
2) Other systems sending capture packets (Kamailio) use the SIP Call-ID.
This causes RTCP information to be uncorrelated to the SIP message
traffic seen by those capture nodes.
In order to support both (in case someone is trying to use res_hep_rtcp
with a non-PJSIP channel), this patch adds a new option, uuid_type, with
two valid values - 'call-id' and 'channel'. The uuid_type option is used
by a module to determine the preferred UUID type. When available, that
source of a correlation UUID is used; when not, the more readily available
source is used.
For res_hep_pjsip:
- uuid_type = call-id: the module uses the SIP Call-ID header value
- uuid_type = channel: the module uses the channel name if available,
falling back to SIP Call-ID if not
For res_hep_rtcp:
- uuid_type = call-id: the module uses the SIP Call-ID header if the
channel type is PJSIP and we have a channel,
falling back to the Stasis event provided
channel name if not
- uuid_type = channel: the module uses the channel name
ASTERISK-25352 #close
Change-Id: Ide67e59a52d9c806e3cc0a797ea1a4b88a00122c
There are two types of SIP URIs indicating a secure transport:
* sips:user@example.org
* sip:user@example.org;transport=tls
When using a sips URI, Asterisk checks incoming INVITEs and answers from
the other side for sips URIs, and rejects the packet if there are only
sip URIs. So Asterisk should only generate a sips Contact URI if the
other side supports it.
This patch makes Asterisk generate either a sip or sips Contact URI
depending on the format of the server URI.
If you want a sip URI, use:
server_uri=sip:example.org\;transport=tls
If you want a sips URI, use:
server_uri=sips:example.org
ASTERISK-25990 #close
Reported-by: Sebastian Damm
Change-Id: I5ae57d6531ce940b5fc64d5cd2673e60db0f9ba2
When reloading, or fetching realtime data, if the "apply" failed for any
numerous reasons the current state object would not be maintained. This
potentially resulted in publishes being stopped for some states/clients when
they should not have been.
This patch makes it so the current state object is kept upon any type of reload/
fetch failures.
Change-Id: Iab6020c116d628ed2ae81183e987e2eaa3c90b30
It was possible for the explicit publish destroy function to be called without
the pjsip client ever being initialized. This fix checks to make sure there is
a client to destroy before attempting.
Change-Id: I8eea1bfa3bd472149bfc255310be2a6248688f5c
The same thing was happening in res_pjsip_publish_asterisk. When the library
was unloaded it did not unregister the object type from sorcery. Subsequent
loads resulted in a failed load due to the sorcery type already existing.
Change-Id: Ifdc25e94e4cd40bc5a19eb4d0a00b86c2e9fedc9
There were a few spots where the client object's reference was being leaked in
sip_outbound_publish_callback. This patch cleans up those leaks.
Change-Id: I485d0bc9335090f373026f77c548042e258461df
When res_pjsip_outbound_publish unloads it has to wait for all current
publishing objects to get done. However if the wait condition times out
then it does not fail the unload. This sometimes results in an infinite
loop check while unloading. This patch now fails the unload operation if
the condition times out.
Change-Id: Id57b8cbed9d61222690fcba1e4f18e259df4c7ec
From the issue reporter:
"res_pjsip_outbound_authenticator_digest builds a nonce that is a hash of
the timestamp, the source address, the source port, a server UUID that is
calculated at startup, and the authentication realm.
Rather than caching nonces that we create, we instead attempt to re-calculate
the nonce when receiving an incoming request with authentication. We then
compare the re-calculated nonce to the incoming nonce, and if they don't match,
then authentication has failed early.
The problem is that it is possible, especially when using TCP, to receive two
requests from the same endpoint but have differing source ports for those
requests. Asterisk itself commonly will use different source ports for
outbound TCP requests."
This patch removes the source port dependency when building the nonce.
ASTERISK-25978 #close
Change-Id: I871b5f4adce102df1c4988066283095ec509dffe
The default tls settings for pjproject only allow TLS 1, TLS 1.1 and TLS 1.2.
SSL is not allowed. So, even if you specify "sslv3" for a transport method,
it's silently ignored and one of the TLS protocols is used. This was a new
behavior of pjsip_tls_setting_default() in 2.4 (when tls.proto was added) that
we never caught.
Now we need to set tls.proto = 0 after we call pjsip_tls_setting_default().
This tells pjproject to set the socket protocol to match the method.
ASTERISK-26004 #close
Change-Id: Icfb55c1ebe921298dedb4b1a1d3bdc3ca41dd078
The res_pjsip_authenticator_digest, res_pjsip_endpoint_identifier_*
and res_pjsip_registrar modules should load ASAP
to avoid "No matching endpoint found" for legitimate endpoint.
ASTERISK-25994
Change-Id: Iac95d95ad031e0be104189d29e923a2ad7c24a1b
This patch modified pjsip_options to retrieve only
permament contacts for aor if the qualify_frequency is > 0
and persisted contacts if the qualify_frequency is > 0.
This patch also fixed a bug in res_sorcery_astdb.
res_sorcery_astdb doesn't save object data retrived from astdb.
ASTERISK-25826
Change-Id: I1831fa46c4578eae5a3e574ee3362fddf08a1f05
With the old SIP module AMI sends PeerStatus event on every
successfully REGISTER requests, ie, on start registration,
update registration and stop registration.
With PJSIP AMI sends ContactStatus only when status is changed.
Regarding registration:
on start registration - Created
on stop registration - Removed
but on update registration nothing
This patch added contact.updated event.
ASTERISK-25904
Change-Id: I8fad8aae9305481469c38d2146e1ba3a56d3108f
The app_fax set FAXMODE variable, but res_fax missing this feature.
This patch add FAXMODE variable which is set to either "audio" or "T38".
ASTERISK-25980
Change-Id: Ie3dcbfb72cc681e9e267a60202f7fb8723a51b6b
The channel and peer V.21 sessions are created on the same channel now.
The peer V.21 session should be created only on peer channel
when one of channel can handle T.38.
Also this patch enable debug for T.38 gateway session
if global fax debug enabled.
ASTERISK-25982
Change-Id: I78387156ea521a77eb0faf170179ddd37a50430e
If the Asterisk system name is set in asterisk.conf, it will be stored
into the "reg_server" field in the ps_contacts table to facilitate
multi-server setups.
ASTERISK-25931
Change-Id: Ia8f6bd2267809c78753b52bcf21835b9b59f4cb8
A feature of chan_sip that service providers relied upon was the ability to
identify by the Authorization username. This is most often used when customers
have a PBX that needs to register rather than identify by IP address. From my
own experiance, this is pretty common with small businesses who otherwise
don't need a static IP.
In this scenario, a register from the customer's PBX may succeed because From
will usually contain the PBXs account id but an INVITE will contain the caller
id. With nothing recognizable in From, the service provider's Asterisk can
never match to an endpoint and the INVITE just stays unauthorized.
The fixes:
A new value "auth_username" has been added to endpoint/identify_by that
will use the username and digest fields in the Authorization header
instead of username and domain in the the From header to match an endpoint,
or the To header to match an aor. This code as added to
res_pjsip_endpoint_identifier_user rather than creating a new module.
Although identify_by was always a comma-separated list, there was only
1 choice so order wasn't preserved. So to keep the order, a vector was added
to the end of ast_sip_endpoint. This is only used by res_pjsip_registrar
to find the aor. The res_pjsip_endpoint_identifier_* modules are called in
globals/endpoint_identifier_order.
Along the way, the logic in res_pjsip_registrar was corrected to match
most-specific to least-specific as res_pjsip_endpoint_identifier_user does.
The order is:
username@domain
username@domain_alias
username
Auth by username does present 1 problem however, the first INVITE won't have
an Authorization header so the distributor, not finding a match on anything,
sends a securty_alert. It still sends a 401 with a challenge so the next
INVITE will have the Authorization header and presumably succeed. As a result
though, that first security alert is actually a false alarm.
To address this, a new feature has been added to pjsip_distributor that keeps
track of unidentified requests and only sends the security alert if a
configurable number of unidentified requests come from the same IP in a
configurable amout of time. Those configuration options have been added to
the global config object. This feature is only used when auth_username
is enabled.
Finally, default_realm was added to the globals object to replace the hard
coded "asterisk" used when an endpoint is not yet identified.
The testsuite tests all pass but new tests are forthcoming for this new
feature.
ASTERISK-25835 #close
Reported-by: Ross Beer
Change-Id: I30ba62d208e6f63439600916fcd1c08a365ed69d
This patch added new global pjsip option 'disable_multi_domain'.
Disabling Multi Domain can improve Realtime performance by reducing
number of database requests.
ASTERISK-25930 #close
Change-Id: I2e7160f3aae68475d52742107949a799aa2c7dc7
The run_agi function is eating control frames when it shouldn't be. This is
causing issues when an AGI is run from CONNECTED_LINE_SEND_SUB in a blond
transfer.
Alice calls Bob. Bob attended transfers to Charlie but hangs up before Charlie
answers.
Alice gets the COLP UPDATE indicating Charlie but Charlie never gets an UPDATE
and is left thinking he's connected to Bob.
In this case, when CONNECTED_LINE_SEND_SUB runs on Alice's channel and it calls
an AGI, the extra eaten frames prevent CONNECTED_LINE_SEND_SUB from running on
Charlie's channel.
The fix was to accumulate deferrable frames in the "forever" loop instead of
dropping them, and re-queue them just before running the actual agi command
or exiting.
ASTERISK-25951 #close
Change-Id: I0f4bbfd72fc1126c2aaba41da3233a33d0433645
We lose the fact that there is a swap channel if there is one. We
currently wind up rejoining the stasis bridge as a normal join after the
swap channel has already been kicked from the bridge.
This patch preserves the swap channel so the AMI/ARI events can note that
the channel joining the bridge is swapping with another channel. Another
benefit to swaqpping in one operation is if there are any channels that
get lonely (MOH, bridge playback, and bridge record channels). The lonely
channels won't leave before the joining channel has a chance to come back
in under stasis if the swap channel is the only reason the lonely channels
are staying in the bridge.
ASTERISK-25947 #close
Reported by: Richard Mudgett
ASTERISK-24649
Reported by: John Bigelow
ASTERISK-24782
Reported by: John Bigelow
Change-Id: If37ea508831d1fed6dbfac2f191c638fc0a850ee
When create_new_id_hdr creates a new RPID or PAI header, it starts by cloning
the From header, then it overwrites the display name and uri from the channel's
connected.id. If the connected.id.name wasn't valid, create_new_id_hdr was
leaving the display name from the From header in the new RPID or PAI header.
On an attended transfer where the originator had a caller id number set but not
a display name, the re-INVITE to the final transferee had the number of the
originator but the display name of the transferer.
Added a check to clear out the display name in the new header if
connected.id.name was invalid.
ASTERISK-25942 #close
Change-Id: I60b4bf7a7ece9b7425eba74151c0b4969cd2738b
The PJSIP parsing functions provide a nice concise way to check the
length of a hostname in a SIP URI. The problem is that in order to use
those parsing functions, it's required to use them from a thread that
has registered with PJLib.
On startup, when parsing AOR configuration, the permanent URI handler
may not be run from a PJLib-registered thread. Specifically, this could
happen when Asterisk was started in daemon mode rather than
console-mode. If PJProject were compiled with assertions enabled, then
this would cause Asterisk to crash on startup.
The solution presented here is to do our own parsing of the contact URI
in order to ensure that the hostname in the URI is not too long. The
parsing does not attempt to perform a full SIP URI parse/validation,
since the hostname in the URI is what is important.
ASTERISK-25928 #close
Reported by Joshua Colp
Change-Id: Ic3d6c20ff3502507c17244a8b7e2ca761dc7fb60
Recent changes to the PJSIP registrar resulted in tests failing due to
missing AOR_CONTACT_ADDED test events. The reason for this was that the
user_agent string had junk values in it, resulting in being unable to
generate the event.
I'm going to be honest here, I have no idea why this was happening. Here
are the steps needed for the user_agent variable to get messed up:
* REGISTER is received
* First contact in the REGISTER results in a contact being removed
* Second contact in the REGISTER results in a contact being added
* The contact, AOR, expiration, and user agent all have to be passed as
format parameters to the creation of a string. Any subset of those
parameters would not be enough to cause the problem.
Looking into what was happening, the thing that struck me as odd was
that the user_agent variable was meant to be set to the value of the
User-Agent SIP header in the incoming REGISTER. However, when removing a
contact, the user_agent variable would be set (via ast_strdupa inside a
loop) to the stored contact's user_agent. This means that the
user_agent's value would be incorrect when attempting to process further
contacts in the incoming REGISTER.
The fix here is to use a different variable for the stored user agent
when removing a contact. Correcting the behavior to be correct also
means the memory usage is less weird, and the issue no longer occurs.
ASTERISK-25929 #close
Reported by Joshua Colp
Change-Id: I7cd24c86a38dec69ebcc94150614bc25f46b8c08
At shutdown it is possible for modules to be unloaded that wouldn't
normally be unloaded. This allows the environment to be cleaned up.
The res_pjsip_transport_management module did not have the unload
logic in it to clean itself up causing the res_pjsip module to not
get unloaded. As a result the res_pjsip monitor thread kept going
processing traffic and timers when it shouldn't.
Change-Id: Ic8cadee131e3b2c436a81d3ae8bb5775999ae00a
The scheduler thread that kills idle TCP connections was not registering
with PJProject properly and causing assertions if PJProject was built in
debug mode.
This change registers the thread with PJProject the first time that the
scheduler callback executes.
AST-2016-005
Change-Id: I5f7a37e2c80726a99afe9dc2a4a69bdedf661283
There are several places that do scheduled tasks or periodic housecleaning,
each with its own implementation:
* res_pjsip_keepalive has a thread that sends keepalives.
* pjsip_distributor has a thread that cleans up expired unidentified requests.
* res_pjsip_registrar_expire has a thread that cleans up expired contacts.
* res_pjsip_pubsub uses ast_sched directly and then calls ast_sip_push_task.
* res_pjsip_sdp_rtp also uses ast_sched to send keepalives.
There are also places where we should be doing scheduled work but aren't.
A good example are the places we have sorcery observers to start registration
or qualify. These don't work when changes are made to a backend database
without a pjsip reload. We need to check periodically.
As a first step to solving these issues, a new ast_sip_sched facility has
been created.
ast_sip_sched wraps ast_sched but only uses ast_sched as a scheduled queue.
When a task is ready to run, ast_sip_task_pusk is called for it. This ensures
that the task is executed in a PJLIB registered thread and doesn't hold up the
ast_sched thread so it can immediately continue processing the queue. The
serializer used by ast_sip_sched is one of your choosing or a random one from
the res_pjsip pool if you don't choose one.
Another feature is the ability to automatically clean up the task_data when the
task expires (if ever). If it's an ao2 object, it will be dereferenced, if
it's a malloc'd object it will be freed. This is selectable when the task is
scheduled. Even if you choose to not auto dereference an ao2 task data object,
the scheduler itself maintains a reference to it while the task is under it's
control. This prevents the data from disappearing out from under the task.
There are two scheduling models.
AST_SIP_SCHED_TASK_PERIODIC specifies that the invocations of the task occur at
the specific interval. That is, every "interval" milliseconds, regardless of
how long the task takes. If the task takes longer than the interval, it will
be scheduled at the next available multiple of interval. For exmaple: If the
task has an interval of 60 secs and the task takes 70 secs (it better not),
the next invocation will happen at 120 seconds.
AST_SIP_SCHED_TASK_DELAY specifies that the next invocation of the task should
start "interval" milliseconds after the current invocation has finished.
Also, the same ast_sched facility for fixed or variable intervals exists. The
task's return code in conjunction with the AST_SIP_SCHED_TASK_FIXED or
AST_SIP_SCHED_TASK_VARIABLE flags controls the next invocation start time.
One res_pjsip.h housekeeping change was made. The pjsip header files were
added to the top. There have been a few cases lately where I've needed
res_pjsip.h just for ast_sip calls and had compiles fail spectacularly because
I didn't add the pjsip header files to my source even though I never referenced
any pjsip calls.
Finally, a few new convenience APIs were added to astobj2 to make things a
little easier in the scheduler. ao2_ref_and_lock() calls ao2_ref() and
ao2_lock() in one go. ao2_unlock_and_unref() does the reverse. A few macros
were also copied from res_phoneprov because I got tired of having to duplicate
the same hash, sort and compare functions over and over again. The
AO2_STRING_FIELD_(HASH|SORT|CMP)_FN macros will insert functions suitable for
aor_container_alloc into your source.
This facility can be used immediately for the situations where we already have
a thread that wakes up periodically or do some scheduled work. For the
registration and qualify issues, additional sorcery and schema changes would
need to be made so that we can easily detect changed objects on a periodic
basis without having to pull the entire database back to check. I'm thinking
of a last-updated timestamp on the rows but more on this later.
Change-Id: I7af6ad2b2d896ea68e478aa1ae201d6dd016ba1c
"Idle" here means that someone connects to us and does not send a SIP
request. PJProject will not automatically time out such connections, so
it's up to Asterisk to do it instead.
When we receive an incoming TCP connection, we will start a timer
(equivalent to transaction timer D) waiting to receive an incoming
request. If we do not receive a request in that timeframe, then we will
shut down the TCP connection.
ASTERISK-25796 #close
Reported by George Joseph
AST-2016-005
Change-Id: I7b0d303e5d140d0ccaf2f7af562071e3d1130ac6
Due to some ignored return values, Asterisk could crash if processing an
incoming REGISTER whose contact URI was above a certain length.
ASTERISK-25707 #close
Reported by George Joseph
Patches:
0001-res_pjsip-Validate-that-URIs-don-t-exceed-pjproject-.patch
AST-2016-004
Change-Id: I0ed3898fe7ab10121b76c8c79046692de3a1be55
* Added Useragent and RegExpire headers to AMI Event
ContactStatusDetail with associated documentation.
ASTERISK-25903 #close
Change-Id: If3d121e943e588d016ba51d4eb9c6a421a562239
Contact expiration can occur in several places: res_pjsip_registrar,
res_pjsip_registrar_expire, and automatically when anyone calls
ast_sip_location_retrieve_aor_contact. At the same time, res_pjsip_registrar
may also be attempting to renew or add a contact. Since none of this was locked
it was possible for one thread to be renewing a contact and another thread to
expire it immediately because it was working off of stale data. This was the
casue of intermittent registration/inbound/nominal/multiple_contacts test
failures.
Now, the new named lock functionality is used to lock the aor during contact
expire and add operations and res_pjsip_registrar_expire now checks the
expiration with the lock held before deleting the contact.
ASTERISK-25885 #close
Reported-by: Josh Colp
Change-Id: I83d413c46a47796f3ab052ca3b349f21cca47059
The first available transport of the appropriate type is used now.
This patch adds new config option 'transport' for outbound-publish.
If transport is set then outbound PUBLISH requests will use this transport.
ASTERISK-25901 #close
Change-Id: Ib389130489b70e36795b0003fa5fd386e2680151
BLF pickup isn't working on Cisco SPA and Snom phones
if the direction="recipient" attribute is missing in 'dialog' tag.
This patch adds direction="recipient" if extension state is
Ringing.
ASTERISK-24601 #close
Change-Id: I5b2c097ca29fd59e92ba237ca5d397cb1b0bcd8c
When shutting down, the PJSIP sorcery is destroyed. The registrar
expiration module queries the PJSIP sorcery to determine what
to expire. As there was no synchronization between termination
of the expiration thread and the unloading of the module it was
possible for the thread to try to access the PJSIP sorcery after
it had been destroyed.
This change ensures that the thread is shut down before allowing
the module to be considered unloaded.
Change-Id: I69fd239edbaaf160c2d37ae00d3ac06e5596fe8b
Some SIP devices indicate hold/unhold using deferred SDP reinvites. In
other words, they provide no SDP in the reinvite.
A typical transaction that starts hold might look something like this:
* Device sends reinvite with no SDP
* Asterisk sends 200 OK with SDP indicating sendrecv on streams.
* Device sends ACK with SDP indicating sendonly on streams.
At this point, PJMedia's SDP negotiator saves Asterisk's local state as
being recvonly.
Now, when the device attempts to unhold, it again uses a deferred SDP
reinvite, so we end up doing the following:
* Device sends reinvite with no SDP
* Asterisk sends 200 OK with SDP indicating recvonly on streams
* Device sends ACK with SDP indicating sendonly on streams
The problem here is that Asterisk offered recvonly, and by RFC 3264's
rules, if an offer is recvonly, the answer has to be sendonly. The
result is that the device is not taken off hold.
What is supposed to happen is that Asterisk should indicate sendrecv in
the 200 OK that it sends. This way, the device has the freedom to
indicate sendrecv if it wants the stream taken off hold, or it can
continue to respond with sendonly if the purpose of the reinvite was
something else (like a session timer refresher).
The fix here is to alter the SDP negotiator's state when we receive a
reinvite with no SDP. If the negotiator's state is currently in the
recvonly or inactive state, then we alter our local state to be
sendrecv. This way, we allow the device to indicate the stream state as
desired.
ASTERISK-25854 #close
Reported by Robert McGilvray
Change-Id: I7615737276165eef3a593038413d936247dcc6ed
I forgot the new voicemail_extension wasn't a stringfield and didn't check
for NULL where I should have.
Change-Id: I029482d5c2ab72474838750461bd46b0809c90fb
The only caller of ari_bridges_play_found() has this note:
If ari_bridges_play_found fails because the channel is unavailable for
playback, The channel will be removed from the playback list soon. We can
keep trying to get channels from the list until we either get one that
will work or else there isn't a channel for this bridge anymore, in which
case we'll revert to ari_bridges_play_new.
Change-Id: Ib068141b367ccaa17be0dab4181c98e26c5127d6
The stasis_app_playback and stasis_app_recording structs need to have a
struct stasis_app_control ref. Other threads can get a reference to the
playback and recording structs from their respective global container.
These other threads can then use the control pointer they contain after
the control struct has gone.
* Add control ref to stasis_app_playback and stasis_app_recording structs.
With the refs added, the control command queue can now have a circular
control reference which will cause the control struct to never get
released if the control's command queue is not flushed when the channel
leaves the Stasis application. Also the command queue needs better
protection from adding commands if the control->is_done flag is set.
* Flush the control command queue on exit.
ASTERISK-25882 #close
Change-Id: I3cf1fb59cbe6f50f20d9e35a2c07ac07d7f4320d
* Give the struct stasis_app_control ao2 object a ref to the channel held
in the object. Now the channel will still be around if a thread needs to
post a stasis message instead of crash because the topic was destroyed.
* Moved stopping any lingering silence generator out of the struct
stasis_app_control destructor and made it a part of exiting the Stasis
application. Who knows which thread the destructor will be called under
so it cannot affect the channel's silence generator. Not only was the
channel unprotected when the silence generator was stopped, stasis may no
longer even control the channel.
ASTERISK-25882
Change-Id: I21728161b5fe638cef7976fa36a605043a7497e4
Background:
If your extension is 1000 and the voicemail access extension is 1571 and you
dial 1571, usually a dialplan rule calls voicemailmain with your extension and
you are placed directly in your mailbox. Therefore most admins program the
voicemail (or other speed dial) button on their phones to the access extension.
Some phones (Snom at least) use whatever is programmed there to also subscribe
for MWI and so can't dial one number and subscribe to another. This works fine
in chan_sip because chan_sip completely ignores the user portion of the
SUBSCRIBE message request URI. If it can match the peer, is subscribes to the
peer's mailbox. The user could be set to anything or nothing and you'd still
get subscribed to your mailbox.
Issue:
chan_pjsip actually uses the user portion of the URI to find an aor and its
mailboxes. Therefore a subscribe to 1571 results in a 404. Sure, you can
create an aor for 1571 but you certainly can't add your entire voicemail
system's mailboxes to it and everyone would get notified of every MWI.
Solution:
When an MWI subscribe comes in and an aor can't be found that matches the
resource directly, check the resource against the endpoint's aors. If an aor
is found that has a voicemail_extension that matches the resource, use it.
ASTERISK-25865
Reported-by: Ross Beer
Change-Id: I770ea185f751f1ada888fafb4b452115f1c06e9e
res_pjsip_mwi was missing the chan_sip "vmexten" functionality which adds
the Message-Account header to the MWI NOTIFY. Also, specifying mailboxes
on endpoints for unsolicited mwi and on aors for subscriptions required
that the admin know in advance which the client wanted. If you specified
mailboxes on the endpoint, subscriptions were rejected even if you also
specified mailboxes on the aor.
Voicemail extension:
* Added a global default_voicemail_extension which defaults to "".
* Added voicemail_extension to both endpoint and aor.
* Added ast_sip_subscription_get_dialog for support.
* Added ast_sip_subscription_get_sip_uri for support.
When an unsolicited NOTIFY is constructed, the From header is parsed, the
voicemail extension from the endpoint is substituted for the user, and the
result placed in the Message-Account field in the body.
When a subscribed NOTIFY is constructed, the subscription dialog local uri
is parsed, the voicemail_extension from the aor (looked up from the
subscription resource name) is substituted for the user, and the result
placed in the Message-Account field in the body.
If no voicemail extension was defined, the Message-Account field is not added
to the NOTIFY body.
mwi_subscribe_replaces_unsolicited:
* Added mwi_subscribe_replaces_unsolicited to endpoint.
The previous behavior was to reject a subscribe if a previous internal
subscription for unsolicited MWI was found for the mailbox. That remains the
default. However, if there are mailboxes also set on the aor and the client
subscribes and mwi_subscribe_replaces_unsolicited is set, the existing internal
subscription is removed and replaced with the external subscription. This
allows an admin to configure mailboxes on both the endpoint and aor and allows
the client to select which to use.
ASTERISK-25865 #close
Reported-by: Ross Beer
Change-Id: Ic15a9415091760539c7134a5ba3dc4a6a1217cea
Commit 1bce690ccb was incrementing txcount
for rtcp packets as well as rtp packets and that was causing sender reports
to be generated instead of receiver reports in cases where no rtp was actually
being sent.
Moved the txcount increment from __rtp_sento, which handles both rtp and rtcp,
to rtp_sento which only handles rtp packets.
Discovered by the hep/rtcp-receiver test.
Change-Id: Ie442e4bb947a68847a676497021ba10ffaf376d5
Added the ability to show channel statistics to chan_pjsip (cli_functions.c)
Moved the existing 'pjsip show channel(s)' functionality from
pjsip_configuration to cli_functions.c. The stats needed chan_pjsip's
private header so it made sense to move the existing channel commands as well.
Now using stasis_cache_dump to get the channel snapshots rather than retrieving
all endpoints, then getting each one's channel snapshots. Much more efficient.
Change-Id: I03b114522126d27434030b285bf6d531ddd79869
No one seemed to notice but every time an OPTIONS goes out, it goes
out with a From of "asterisk" (or whatever the default from_user is set to),
even if you specify an endpoint.
The issue had several causes...
qualify_contact is only called with an endpoint if called from the CLI.
If the endpoint is NULL, qualify_contact only looks up the endpoint if
authenticate_qualify=yes. Even then, it never passes it on to
ast_sip_create_request where the From header is set. Therefore From
is always "asterisk" (or whatever the default from_user is set to).
Even if ast_sip_create_request were to get an endpoint, it only sets
the From if endpoint->from_user is set.
The fix is 4 parts...
First, create_out_of_dialog_request was modified to use the endpoint id
if endpoint was specified and from_user is not set.
Second, qualify_contact was modified to always look up an endpoint if
one wasn't specified regardless of authenticate_qualify. It then passes
the endpoint on to create_out_of_dialog_request.
Third (and most importantly), find_an_endpoint was modified to find
an endpoint by using an "aors LIKE %contact->aor%" predicate with
ast_sorcery_retrieve_by_fields. As such, this patch will only work
if the sorcery realtime optimizations patch goes in. Otherwise we'd
be pulling the entire endpoints database every time we send an OPTIONS.
Since we already know the contact's aor, the on_endpoint callback was also
modified to just check if the contact->aor is an exact match to one of
the endpoint's.
Finally, since we now have an endpoint for every OPTIONS request,
res_pjsip/endpt_send_request (which handles out-of-dialog reqests) was
updated to get the transport from the endpoint and set it on tdata.
Now the correct transport is used.
Change-Id: I2207e12bb435e373bd1e03ad091d82e5aba011af
Asterisk uses separate UDP ports for RTP and RTCP traffic and RFC 5764
explicitly states:
There MUST be a separate DTLS-SRTP session for each distinct pair of
source and destination ports used by a media session
This means RTP keying material cannot be used for DTLS RTCP, which was
the reason why RTCP encryption would fail.
ASTERISK-25642
Change-Id: I7e8779d8b63e371088081bb113131361b2847e3a
rxcount, txcount, rxoctetcount and txoctetcount weren't being calculated
for bridged streams because the calulations were being done after the
bridged short-circuit. Actually, rxoctetcount wasn't ever being calculated.
Moved the calculations so they occur for all valid received packets and
all transmitted packets. Also added rxoctetcount and txoctetcount to
ast_rtp_instance_stat.
Change-Id: I08fb06011a82d38c3b4068867a615068fbe59cbb
Blind transfers to a recognized parking extension need to use the parker's
channel variable values to create the dynamic parking lot. This is
because there is always only one parker while the parkee may actually be a
multi-party bridge. A multi-party bridge can never supply the needed
channel variables to create the dynamic parking lot. In the multi-party
bridge blind transfer scenario, the parker's CHANNEL(parkinglot) value and
channel variables are inherited by the local channel used to park the
bridge.
* In park_common_setup(), make use the parker instead of the parkee to
supply the dynamic parking lot channel variable values. In all but one
case, the parkee is the same as the parker. However, in the recognized
parking extension blind transfer scenario for a two party bridge they are
different channels. For consistency, we need to use the parker channel.
* In park_local_transfer(), pass the CHANNEL(parkinglot) value to the
local channel when blind transferring a multi-party bridge to a recognized
parking extension.
* When a local channel starts a call, the Local;2 side needs to inherit
the CHANNEL(parkinglot) value from Local;1.
The DTMF one-touch parking case wasn't even trying to create dynamic
parking lots before it aborted the attempt.
* In parking_park_call(), add missing code to create a dynamic parking
lot.
A DTMF bridge hook is documented as returning -1 to remove the hook.
Though the hook caller is really coded to accept non-zero. See the
ast_bridge_hook_callback typedef.
* In feature_park_call(), don't remove the DTMF one-touch parking hook
because of an error.
ASTERISK-24605 #close
Reported by: Philip Correia
Patches:
call_park.patch (license #6672) patch uploaded by Philip Correia
Change-Id: I221d3a8fcc181877a1158d17004474d35d8016c9
There were a number of places in the res_pjsip stack that were getting
all endpoints or all aors, and then filtering them locally.
A good example is pjsip_options which, on startup, retrieves all
endpoints, then the aors for those endpoints, then tests the aors to see
if the qualify_frequency is > 0. One issue was that it never did
anything with the endpoints other than retrieve the aors so we probably
could have skipped a step and just retrieved all aors. But nevermind.
This worked reasonably well with local config files but with a realtime
backend and thousands of objects, this was a nightmare. The issue
really boiled down to the fact that while realtime supports predicates
that are passed to the database engine, the non-realtime sorcery
backends didn't.
They do now.
The realtime engines have a scheme for doing simple comparisons. They
take in an ast_variable (or list) for matching, and the name of each
variable can contain an operator. For instance, a name of
"qualify_frequency >" and a value of "0" would create a SQL predicate
that looks like "where qualify_frequency > '0'". If there's no operator
after the name, the engines add an '=' so a simple name of
"qualify_frequency" and a value of "10" would return exact matches.
The non-realtime backends decide whether to include an object in a
result set by calling ast_sorcery_changeset_create on every object in
the internal container. However, ast_sorcery_changeset_create only does
exact string matches though so a name of "qualify_frequency >" and a
value of "0" returns nothing because the literal "qualify_frequency >"
doesn't match any name in the objset set.
So, the real task was to create a generic string matcher that can take a
left value, operator and a right value and perform the match. To that
end, strings.c has a new ast_strings_match(left, operator, right)
function. Left and right are the strings to operate on and the operator
can be a string containing any of the following: = (or NULL or ""), !=,
>, >=, <, <=, like or regex. If the operator is like or regex, the
right string should be a %-pattern or a regex expression. If both left
and right can be converted to float, then a numeric comparison is
performed, otherwise a string comparison is performed.
To use this new function on ast_variables, 2 new functions were added to
config.c. One that compares 2 ast_variables, and one that compares 2
ast_variable lists. The former is useful when you want to compare 2
ast_variables that happen to be in a list but don't want to traverse the
list. The latter will traverse the right list and return true if all
the variables in it match the left list.
Now, the backends' fields_cmp functions call ast_variable_lists_match
instead of ast_sorcery_changeset_create and they can now process the
same syntax as the realtime engines. The realtime backend just passes
the variable list unaltered to the engine. The only gotcha is that
there's no common realtime engine support for regex so that's been noted
in the api docs for ast_sorcery_retrieve_by_fields.
Only one more change to sorcery was done... A new config flag
"allow_unqualified_fetch" was added to reg_sorcery_realtime.
"no": ignore fetches if no predicate fields were supplied.
"error": same as no but emit an error. (good for testing)
"yes": allow (the default);
"warn": allow but emit a warning. (good for testing)
Now on to res_pjsip...
pjsip_options was modified to retrieve aors with qualify_frequency > 0
rather than all endpoints then all aors. Not only was this a big
improvement in realtime retrieval but even for config files there's an
improvement because we're not going through endpoints anymore.
res_pjsip_mwi was modified to retieve only endpoints with something in
the mailboxes field instead of all endpoints then testing mailboxes.
res_pjsip_registrar_expire was completely refactored. It was retrieving
all contacts then setting up scheduler entries to check for expiration.
Now, it's a single thread (like keepalive) that periodically retrieves
only contacts whose expiration time is < now and deletes them. A new
contact_expiration_check_interval was added to global with a default of
30 seconds.
Ross Beer reports that with this patch, his Asterisk startup time dropped
from around an hour to under 30 seconds.
There are still objects that can't be filtered at the database like
identifies, transports, and registrations. These are not going to be
anywhere near as numerous as endpoints, aors, auths, contacts however.
Back to allow_unqualified_fetch. If this is set to yes and you have a
very large number of objects in the database, the pjsip CLI commands
will attempt to retrive ALL of them if not qualified with a LIKE.
Worse, if you type "pjsip show endpoint <tab>" guess what's going to
happen? :) Having a cache helps but all the objects will have to be
retrieved at least once to fill the cache. Setting
allow_unqualified_fetch=no prevents the mass retrieve and should be used
on endpoints, auths, aors, and contacts. It should NOT be used for
identifies, registrations and transports since these MUST be
retrieved in bulk.
Example sorcery.conf:
[res_pjsip]
endpoint=config,pjsip.conf,criteria=type=endpoint
endpoint=realtime,ps_endpoints,allow_unqualified_fetch=error
ASTERISK-25826 #close
Reported-by: Ross Beer
Tested-by: Ross Beer
Change-Id: Id2691e447db90892890036e663aaf907b2dc1c67
res/parking/parking_applications.c:
* Add malloc fail checks in setup_park_common_datastore().
* Fix playing parking failed announcement to only happen on non-blind
transfers in park_app_exec(). It could never go out before because a test
was provedly always false.
res/parking/parking_bridge.c:
* Fix NULL tolerance in generate_parked_user() because
bridge_parking_push() can theoretically pass a NULL parker channel if the
parker channel went away for some reason.
* Clarify some weird code dealing with blind_transfer in
bridge_parking_push().
res/parking/parking_bridge_features.c:
* Made park_local_transfer() set BLINDTRANSFER on the Local;1 channel
which will be bulk copied to the Local;2 channel on the subsequent
ast_call(). The additional advantage is if the parker channel has the
BLINDTRANSFER and ATTENDEDTRANSFER variables set they are now guaranteed
to be overridden.
res/parking/parking_manager.c:
* Fix AMI Park action input range checking of the Timeout header in
manager_park().
* Reduced locking scope to where needed in manager_park().
res/res_parking.c:
* Fix some off nominal missing unlocks by eliminating the returns.
Change-Id: Ib64945bc285acb05a306dc12e6f16854898915ca
The configuration unsigned integer option handler sets flags for the
parser as if the option should be a signed integer (PARSE_INT32),
leading to errors on "out of range" values. Fix flags (PARSE_UINT32).
A fix to res_pjsip is also present which stops invalid flags from
being passed when registering sorcery object fields for qualify
status.
ASTERISK-25612 #close
Change-Id: I96b539336275e0e72a8e8033487d2c3344debd3e
The log message when a MusicOnHold music class was not found was changed
from debug level to WARNING level in Asterisk 11.19 and 13.5. For those
using realtime musiconhold, this message is wrong because it warns
before checking the database.
This changeset delays the warning until after the database has been
checked.
Reported-by: Conrad de Wet
ASTERISK-25444 #close
Change-Id: I6cfb2db2f9cfbd2bb3d30566ecae361c4abf6dbf
The "Refer-to" header of an incoming REFER request is parsed by
pjsip_parse_uri(). That function requires the URI parameter to be NULL
terminated. Unfortunately, the previous code added the NULL terminator by
overwriting memory that may not be safe. The overwritten memory results
could be benign, memory corruption, or a segmentation fault. Now the URI
is NULL terminated safely by copying the URI to a new chunk of memory with
the correct size to be NULL terminated.
ASTERISK-25814 #close
Change-Id: I32565496684a5a49c3278fce06474b8c94b37342
Older versions of PJSIP do not have the proto field on the TLS transport
setting structure. This change adds a configure check so even if it is
not present we will still be able to build.
Change-Id: Ibf3f47befb91ed1b8194bf63888baa6fee05aba9
Per RFC3325, the 'From' header is now anonymized on outgoing calls when
caller id presentation is prohibited.
TID = trust_id_outbound
PRO = Set(CALLERID(pres)=prohib)
USR = endpoint/from_user
DOM = endpoint/from_domain
PAI = YES(privacy=off), NO(not sent), PRI(privacy=full) (assumes send_pai=yes)
Conditions |Result
--------------------|----------------------------------------------------
TID PRO USR DOM |PAI FROM
--------------------|----------------------------------------------------
Y Y abc def.ghi |PRI "Anonymous" <sip:abc@def.ghi>
Y Y abc |PRI "Anonymous" <sip:abc@anonymous.invalid>
Y Y def.ghi |PRI "Anonymous" <sip:anonymous@def.ghi>
Y Y |PRI "Anonymous" <sip:anonymous@anonymous.invalid>
Y N abc def.ghi |YES <sip:abc@def.ghi>
Y N abc |YES <sip:abc@<ip_address>>
Y N def.ghi |YES "Caller Name" <sip:<caller_exten>@def.ghi>
Y N |YES "Caller Name" <sip:<caller_exten>@<ip_address>>
N Y abc def.ghi |NO "Anonymous" <sip:abc@def.ghi>
N Y abc |NO "Anonymous" <sip:abc@anonymous.invalid>
N Y def.ghi |NO "Anonymous" <sip:anonymous@def.ghi>
N Y |NO "Anonymous" <sip:anonymous@anonymous.invalid>
N N abc def.ghi |YES <sip:abc@def.ghi>
N N abc |YES <sip:abc@<ip_address>>
N N def.ghi |YES "Caller Name" <sip:<caller_exten>@def.ghi>
N N |YES "Caller Name" <sip:<caller_exten>@<ip_address>>
ASTERISK-25791 #close
Reported-by: Anthony Messina
Change-Id: I2c82a5ca1413c2c00fb62ea95b0ae8e97af54dc9
During the transfer process, some phones (okay it was the Jitsi softphone,
but maybe others are out there) send a "bye" immediately after receiving a
SIP Notify. When a "bye" is received early for some types of transfers the
transferer channel may no longer be available during late stage transfer
processing.
For instance, during an attended transfer involving stasis bridging at one
point the created local channel looks for an associated swap channel in
order to retrieve the stasis application name. If the transferer has hung
up then the local channel will fail to find it. The local channel then has
no way to know which stasis app to enter, so it fails and hangs up as well.
Thus the transfer does not complete as expected.
This patch delays the sending of the initial notify in order to give the
transfer process enough time to gather the necessary data for a successful
transfer.
ASTERISK-25771
Change-Id: I09cfc9a5d6ed4c007bc70625e0972b470393bf16
PJSIP does not ensure that when printing the message body the
buffer will be NULL terminated. This is problematic when searching
for the signal and duration values of the DTMF.
This change ensures the buffer is always NULL terminated.
Change-Id: I52653a1a60c93092d06af31a27408d569cc98968
ast_sip_get_transport_states was returning a container of internal_state
objects instead of ast_sip_transport_state objects. This was causing
transport lookups to fail, most noticably in res_pjsip_nat, which
couldn't find the correct external addresses. This was causing contacts
to go out with internal ip addresses.
ASTERISK-25830 #close
Reported-by: Sean Bright
Change-Id: I1aee6a2fd46c42e8dd0af72498d17de459ac750e
In message.c, if msg_alloc fails to init the string field,
vars may be null, so use a null tolerant cleanup.
In res_pjsip_messaging.c, if msg_data_create fails, mdata
will be null, so use a null tolerant cleanup.
ASTERISK-25323
Change-Id: Ic2d55c2c3750d5616e2a05ea92a19c717507ff56
Previous chan_sip behavior:
Before this patch chan_sip would always strip any quotes from an incoming
reason and pass that value up as the REDIRECTING(reason). For an outgoing
reason value, chan_sip would check the value against known values and
quote any it didn't recognize. Incoming 480 response message reason text
was just assigned to the REDIRECTING(reason).
Previous chan_pjsip behavior:
Before this patch chan_pjsip would always pass the incoming reason value
up as the REDIRECTING(reason). For an outgoing reason value, chan_pjsip
would send the reason value as passed down.
With this patch:
Both channel drivers match incoming reason values with values documented
by REDIRECTING(reason) and values documented by RFC5806 regardless of
whether they are quoted or not. RFC5806 values are mapped to the
equivalent REDIRECTING(reason) documented value and is set in
REDIRECTING(reason). e.g., an incoming RFC5806 'unconditional' value or a
quoted string version ('"unconditional"') is converted to
REDIRECTING(reason)'s 'cfu' value. The user's dialplan only needs to deal
with 'cfu' instead of any of the aliases.
The incoming 480 response reason text supported by chan_sip checks for
known reason values and if not matched then puts quotes around the reason
string and assigns that to REDIRECTING(reason).
Both channel drivers send outgoing known REDIRECTING(reason) values as the
unquoted RFC5806 equivalent. User custom values are either sent as is or
with added quotes if SIP doesn't allow a character within the value as
part of a RFC3261 Section 25.1 token. Note that there are still
limitations on what characters can be put in a custom user value. e.g.,
embedding quotes in the middle of the reason string is silly and just
going to cause you grief.
* Setting a REDIRECTING(reason) value now recognizes RFC5806 aliases.
e.g., Setting REDIRECTING(reason) to 'unconditional' is converted to the
'cfu' value.
* Added missing malloc() NULL return check in res_pjsip_diversion.c
set_redirecting_reason().
* Fixed potential read from a stale pointer in res_pjsip_diversion.c
add_diversion_header(). The reason string needed to be copied into the
tdata memory pool to ensure that the string would always be available.
Otherwise, if the reason string returned by reason_code_to_str() was a
user's reason string then the string could be freed later by another
thread.
Change-Id: Ifba83d23a195a9f64d55b9c681d2e62476b68a87
* Fix double unref of other_party channel in off nominal path.
* This is unlikely to be a real problem. However, for safety,
in handle_incoming_request() keep the datastore ref with the
other_party channel ref until we are finished with the other_party
channel.
Change-Id: I78f22547bf0bb99fb20814ceab75952bd857f821
This backs out item 4 of the 4875e5ac32
commit. Item 4 added the t38_bye_supplement. Unfortunately, the frame
that it puts into the bridge may or may not be processed by the time the
bridged peer is kicked out of the bridge. If it is processed then all is
well. However, if it is not processed then that channel is stuck in fax
mode until it hangs up or maybe if it joins another bridge for T.38
faxing.
ASTERISK-25582
Change-Id: Ib20a03ecadf1bf8a0dcadfadf6c2f2e60919a9f7
There are a few cases where we're emitting notices or warnings
for things that really need neither, like a client retrying to subscribe
to mwi when they're not conifgured for it. They get a 404 so there's no
need for non-debug messages.
Change-Id: I05e38a7ff6c2f2521146f4be6a79731b9864e61f
Introduced realloaction of ast_str buf in sqlite3_escape functions in case
the returned buffer from threadstorage was actually too small.
Change-Id: I3c5eb43aaade93ee457943daddc651781954c445
The 'reload' mechanism actually involves closing the underlying
socket and calling the appropriate udp, tcp or tls start functions
again. Only outbound_registration, pubsub and session needed work
to reset the transport before sending requests to insure that the
pjsip transport didn't get pulled out from under them.
In my testing, no calls were dropped when a transport was changed
for any of the 3 transport types even if ip addresses or ports were
changed. To be on the safe side however, a new transport option was
added (allow_reload) which defaults to 'no'. Unless it's explicitly
set to 'yes' for a transport, changes to that transport will be ignored
on a reload of res_pjsip. This should preserve the current behavior.
Change-Id: I5e759850e25958117d4c02f62ceb7244d7ec9edf
Warnings and errors in the pjproject libraries are generally handled by
Asterisk. In many cases, Asterisk wouldn't even consider them to be warnings
or errors so the messages emitted by pjproject directly are either superfluous
or misleading. A good exampe of this are the level-0 errors pjproject emits
when it can't open a TCP/TLS socket to a client to send an OPTIONS. We don't
consider a failure to qualify a UDP client an "ERROR", why should a TCP/TLS
client be treated any differently?
A config file for res_pjproject has bene added (pjproject.conf) and a new
log_mappings object allows mapping pjproject levels to Asterisk levels
(or nothing). The defaults if no pjproject.conf file is found are the same
as those that were hard-coded into res_pjproject initially: 0,1 = LOG_ERROR,
2 = LOG_WARNING, 3,4,5 = LOG_DEBUG<level>
Change-Id: Iba7bb349c70397586889b8f45b8c3d6c6c8c3898
When Asterisk receives a 412 (Conditional Request Failed) response
it has to recreate publish session.
There is bug in res_pjsip_outbound_publish.c
The function sip_outbound_publish_client_alloc is called with wrong object
while processing 412 (Conditional Request Failed) response.
This patch fixes it.
ASTERISK-25229 #close
Change-Id: I3b62f2debf6bb1e5817cde7b13ea39ef2bf14359
res_statsd.export.in was missing the _va variations of the log
functions causing Asterisk to crash in res_pjsip if OPTIONAL_API
wasn't enabled.
ASTERISK-25727 #close
Reported-by: Gergely Dömsödi
Change-Id: I395729f9f51bdd33c5ca757f5f96ebedad74077b
A new command (pjsip export config_wizard primitives) has been added that
will export all the pjsip objects it created to the console or a file
suitable for reuse in a pjsip.conf file.
ASTERISK-24919 #close
Reported-by: Ray Crumrine
Change-Id: Ica2a5f494244b4f8345b0437b16d06aa0484452b
If the PJSIP_HEADER dialplan function adds a PAI or RPID header and send_rpid
or send_pai is set, res_pjsip_caller_id attemps to retrieve, parse and modify
the header added by the dialplan function. Since the header added by the
dialplan function is generic string, there are no virtual functions to parse
the uri and we get a segfault when we try. Since the modify, was really only
an overwrite, we now just delete the old header if it was type PJSIP_H_OTHER
and recreate it.
This raises a question for another time though: What should happen with
duplicate headers? Right now res_pjsip_header_funcs doesn't check for dups
so if it's session supplement is loaded after res_pjsip_caller_id's (or any
other module that adds headers), there'll be dups in the message.
ASTERISK-25337 #close
Change-Id: I5e296b52d30f106b822c0eb27c4c2b0e0f71c7fa
It is possible when processing a SIP REGISTER request to have two
threads end up creating contact_status structures in sorcery.
contact_status is created using a "find or create" function. If two
threads call into this at the same time, each thread will fail to find
an existing contact_status, and so both will end up creating a new
contact status.
During testing, we would see sporadic failures because the
PJSIP_CONTACT() dialplan function would operate on a different
contact_status than what had been updated by res_pjsip/pjsip_options.
The fix here is two-fold:
1) The "find or create" function for contact_status now has a lock
around the entire operation. This way, if two threads attempt the
operation simultaneously, the first to get there will create the object,
and the second will find the object created by the first thread.
2) res_sorcery_memory has had its create callback updated so that it
will not allow for objects with duplicate IDs to be created.
Change-Id: I55b1460ff1eb0af0a3697b82d7c2bac9f6af5b97
A problem arose when testing the AMI subscription listing actions where it
was possible for a subscription that had not been fully initialized to be
listed. This was problematic as the underlying listing code would crash.
This change makes it so the subscription tree is fully set up before it is
added to the list of subscriptions. This ensures that when the listing actions
get the subscription it is valid.
ASTERISK-25738 #close
Change-Id: Iace2b13641c31bbcc0d43a39f99aba1f340c0f48
load_module was just too hairy with every step having to clean up all
previous steps on failure.
Some of the pjproject init calls have now been moved to a separate
load_pjsip function and the unload_pjsip function was enhanced to clean
up everything if an error happened at any stage of the load process.
In the process, a bunch of missing pj_shutdowns, serializer_pool_shutdowns
and ast_threadpool_shutdowns were also corrected.
Change-Id: I5eec711b437c35b56605ed99537ebbb30463b302
* heap-use-after-free happens when we free "cfg"
but then use "value" which refers to it
* A memory leak occurs because in some cases
it is not released "defaults"
ASTERISK-25721 #close
Reported by: Badalyan Vyacheslav
Tested by: Badalyan Vyacheslav
Change-Id: I3807d3f4726df6864430ec144cf6265d3f538469
Pjproject has deprecated pjsip_dlg_create_uas in 2.5 and replaced it with
pjsip_dlg_create_uas_and_inc_lock which, as the name implies, automatically
increments the lock on the returned dialog. To account for this, configure.ac
now detects the presence of pjsip_dlg_create_uas_and_inc_lock and res_pjsip.c
has an #ifdef HAVE_PJSIP_DLG_CREATE_UAS_AND_INC_LOCK to decide whether to use
the original call or the new one. If the new one was used, the ref count is
decremented before returning.
ASTERISK-25751 #close
Reported-by Josh Colp
Change-Id: I1be776b94761df03bd0693bc7795a75682615ca8
Attempting to load a transport from realtime was forcing asterisk into an
infinite recursion loop. The first thing transport_apply did was to do a
sorcery retrieve by id for an existing transport of the same name. For files,
this just returns the previous object from res_sorcery_config's internal
container, if any. For realtime, the res_sourcery_realtime driver looks in the
database and finds the existing row but now it has to rehydrate it into a
sorcery object which means calling... transport_apply. And so it goes.
The main issue with loading from realtime (apart from the loop) was that
transport stores structures and pointers directly in the ast_sip_transport
structure instead of the separate ast_transport_state structure. This patch
separates those items into the ast_sip_transport_state structure. The pattern
is roughly the same as res_pjsip_outbound_registration.
Although all current usages of ast_sip_transport and ast_sip_transport_state
were modified to use the new ast_sip_get_transport_state API, the original
items are left in ast_sip_transport and kept updated to maintain ABI
compatability for third-party modules. They are marked as deprecated and
noted that they're now in ast_sip_transport_state.
ASTERISK-25606 #close
Reported-by: Martin Moučka
Change-Id: Ic7a836ea8e786e8def51fe3f8cce855ea54f5f19
Device state subscription lifetimes were governed by when the
subscription was established and unsubscribed from. However, it is
possible that at the time of unsubscription, there could be device state
events still in flight. When those device state events occur, the device
state callback could attempt to dereference a freed pointer. Crash.
This change ensures that the lifetime of the device state subscription
does not end until the underlying stasis subscription has confirmed that
its final message has been sent.
Change-Id: I25a0f1472894c1a562252fb7129671478e25e9b2
During ICE negotiation the IPs of the local interfaces are sent to the remote
peer as host candidates. In many cases Asterisk is behind a static one-to-one
NAT, so these host addresses will be internal IP addresses.
To help in hiding the topology of the internal network, this patch adds the
ability to override the host candidates by matching them against a
user-defined list of replacements.
Change-Id: I1c9541af97b83a4c690c8150d19bf7202c8bff1f
test_dlinklists doesn't need to NOTICE everyone that every macro worked.
res_phoneprov doesn't need to VERBOSE everyone that a phoneprov extension or
provider was registered.
res_odbc was missing a newline at the end of one message.
Change-Id: I6c06361518ef3711821795e535acd439782a995e
A regression was introduced where searching for realtime PJSIP objects
by regex by starting the regex with a leading "^" would cause no items
to be returned.
This was due to a change which attempted to drop the requirement for a
leading "^" to be present due to how some CLI commands formulate their
regexes. However, the change, rather than simply eliminating the
requirement, caused any regexes that did begin with "^" to end up not
returning the expected results.
This change fixes the problem by inspecting the regex and formulating
the realtime query differently depending on if it begins with "^".
ASTERISK-25702 #close
Reported by Nic Colledge
Patches:
realtime_retrieve_regex.patch submitted by Alexei Gradinari License #5691
Change-Id: I055df608a6e6a10732044fa737a9fe8dca602693
The module res_xmpp does not accept usernames in the form used in component
mode (XEP-0114). In component mode there is no @something in the name.
In component mode the connection is now not dropped anymore.
If the xmpp server sends out a "stream" tag before handshake is finished,
the connection gets dropped in res_xmpp. Now this tag will be ignored and
the connection will be established.
After connecting there will be an exchange of presence states. This does
not work as expected in component mode. The responsible function
"xmpp_pak_presence" is left before the states get sent out. Sending
presence states in component mode is now moved to the top of the function.
ASTERISK-25735 #close
Change-Id: I70e036f931c3124ebb2ad1e56f93ed35cfdd9d5c
The "clean" target was attempting to clean res/ari from inside
the res directory which doesn't remove anything. Removed the res/
prefix.
Change-Id: Ib1a518d54efa81b9fd5a42742d43cc3767435bf6
Asterisk by default will create a single database connection and share
it among all threads that attempt to access the database. In previous
versions of Asterisk, this was tolerable, because the most used channel
driver, chan_sip, mostly accessed the database from a single thread.
With PJSIP, however, many threads may be attempting to perform database
operations, and there is the potential for many more database accesses,
meaning the concurrency is a horrible bottleneck if only one connection
is shared.
Asterisk has a connection pooling facility built into it, but the
implementation has flaws. For one, there is a strict limit on the number
of simultaneous connections that could be made to the database. Anything
beyond the maximum would result in a failed operation. Attempting to
predict what the maximum should be is nearly impossible even for someone
intimately familiar with Asterisk's threading model. In addition, use of
transactions in the dialplan can cause some severe bugs if connection
pooling is enabled.
This commit seeks to fix the concurrency problem by removing all
connection management code from Asterisk and leaving that to the
underlying unixODBC code instead. Now, Asterisk does not share a single
connection, nor does it try to maintain a connection pool. Instead, all
Asterisk ever does is request a connection from unixODBC and allow
unixODBC to either allocate those connections or retrieve them from a
pool.
Doing this has a bit of a ripple effect. For one, since connections are
not long-lived objects, several of the safeguards that previously
existed have been removed. We don't have to worry about trying to use a
connection that has gone stale. In every case, when we request a
connection, it has just been made and we don't need to perform any
sanity checks to be sure it's still active.
Another major player affected by this change is transactions.
Transactions and their respective connections were so tightly coupled
that it was almost pornographic. This code change moves
transaction-related code to its own file separate from the core ODBC
functionality. This way, the core of ODBC does not even have to know
that transactions exist.
In making this large change, I had to look at a lot of code and
understand it. When making this change, I discovered several places
where the behavior is definitely not ideal, but it seemed outside the
scope of this change to be fixing it. Instead, any place where I saw
some sort of room for improvement has had a XXX comment added explaining
what could be altered to improve it.
Change-Id: I37a84def5ea4ddf93868ce8105f39de078297fbf
A recent change to queue channel variable setting to the Stasis control
queue caused a regression. When setting channel variables, it is
possible to give a NULL channel variable value in order to unset the
variable (i.e. remove it from the channel variable list). The change
introduced a call to ast_variable_new(), which is not tolerant of NULL
channel variable values.
This new change switches from using ast_variable to using a custom
channel variable struct that is lighter weight and NULL value-tolerant.
Change-Id: I784d7beaaa3c036ea936d103e7caf0bb1562162d
A test recently uncovered that running an ill-timed AMI command to show
inbound subscriptions could cause a crash since Asterisk will try to
operate on a freed subscription.
The fix for this is to remove the subscription tree from the list of
subscriptions at the time that we are sending our final NOTIFY request
out. This way, as the subscription is in the process of dying, it is
inaccessible from AMI.
Change-Id: Ic0239003d8d73e04c47c12dd2a7e23867e5b5b23
When queuing tasks onto the Stasis control queue, you can pass an
arbitrary data pointer and a function to free that data. All ARI
commands that use the Stasis control queue made the assumption that the
destructor function would be called in all paths, whether the task was
queued successfully or not. However, this was not correct. If a task was
queued onto a control structure that was already completed, the
allocated data would not be freed properly.
This patch corrects this by making sure that all return paths call the
data destructor.
Change-Id: Ibf06522094f8e5c4cce652537dc5d7222b1c4fcb
A crash occurred when attempting to set a channel variable on a channel
that had already been hung up. This is because there is a small window
between when a control is grabbed and when the channel variable is set
that the channel can be hung up.
The fix here is to queue the setting of the channel variable onto the
control queue. This way, the manipulation of the channel happens in a
thread where it is safe to be done.
In this change, I also noticed that the setting of bridge roles on
channels was being done outside of the control queue, so I also changed
those operations to be done in the control queue.
ASTERISK-25709 #close
Reported by Mark Michelson
Change-Id: I2a0a4d51bce6fba6f1d9954e40935e42f366ea78
Dump the res_pjsip endpt internals.
In non-developer mode we will not document or make easily accessible the
"details" option even though it is still available. The user has to know
it exists to use it. Presumably they would also be aware of the potential
crash warning below.
Warning: PJPROJECT documents that the function used by this CLI command
may cause a crash when asking for details because it tries to access all
active memory pools.
Change-Id: If2d98a3641c9873364d1daaad971376311aef3cb
res_pjsip_log_forwarder has been renamed to res_pjproject
and enhanced as follows:
As a follow-on to the recent 'Add CLI "pjsip show buildopts"' patch,
a new ast_pjproject_get_buildopt function has been added. It
allows the caller to get the value of one of the buildopts.
The initial use case is retrieving the runtime value of
PJ_MAX_HOSTNAME to insure we don't send a hostname greater
than pjproject can handle. Since it can differ between
the version of pjproject that Asterisk was compiled against
and the version of pjproject that Asterisk is running against,
we can't use the PJ_MAX_HOSTNAME macro directly in Asterisk
source code.
Change-Id: Iab6e82fec3d7cf00c1cf6185c42be3e7569dee1e
'make clean' and 'make distclean' can leave behind .o files in the
res/ari/ directory. One observed consequence of this is that running
Asterisk with MALLOC_DEBUG can cause Asterisk to crash immediately on
startup sometimes.
By ensuring that we are making a clean build, we can be sure that stale
files are not being included in the build and causing problems when
build options should have caused files to be re-built.
ASTERISK-25683 #close
Reported by yaron nahum
Change-Id: I1f48baa904d2468eddeefb42ee68a56af7adc7b7
There are two ways in which the reload() function in res_musiconhold can be
called from the CLI:
* module reload res_musiconhold.so
* moh reload
In the former case, the module loader holds a lock that prevents multiple
concurrent calls, but in the latter there is no such protection.
This patch changes the 'moh reload' CLI command to invoke the module loader
directly, rather than call reload() explicitly.
ASTERISK-25687 #close
Change-Id: I408968b4c8932864411b7f9ad88cfdc7b9ba711c
PJPROJECT has a function available to dump the compile time
options used when building the library.
* Add CLI "pjsip show buildopts" command.
* Update contrib/scripts/autosupport to get pjproject information.
Change-Id: Id93a6a916d765b2a2e5a1aeb54caaf83206be748
res_sorcery_realtime's search-by-regex callback performed a check to
ensure that the passed-in regex began with a caret (^). If it did not,
then no results would be returned.
This callback only started to become used when "like" support was added
to PJSIP CLI commands. The CLI command for listing objects would pass an
empty regex ("") to the sorcery backend if no "like" statement was
present. For most sorcery backends, this resulted in returning all
objects. However, for realtime, this resulted in returning no objects.
This commit seeks to fix the regression by removing the requirement from
res_sorcery_realtime for the passed-in-regex to begin with a caret.
ASTERISK-25689 #close
Reported by Marcelo Terres
Change-Id: I22b4dc5d7f3f11bb29ac2e42ef94682e9bab3b20
On a system with multiple ip addresses in the same subnet, if a
transport is bound to a specific ip address and endpoint/media_address
is set, the SIP/SDP will have the correct address in all fields but
the rtp stream MAY still originate from one of the other ip addresses,
most probably the "primary" ip address. This happens because
res_pjsip_sdp_rtp/create_rtp always calls ast_instance_new with
the "all" ip address (0.0.0.0 or ::).
The new option causes res_pjsip_sdp_rtp/create_rtp to call
ast_rtp_instance_new with the endpoint's media_address (if specified)
instead of the "all" address. This causes the packets to originate from
the specified address.
ASTERISK-25632
ASTERISK-25637
Reported-by: Olivier Krief
Reported-by: Dan Journo
Change-Id: I3dfaa079e54ba7fb7c4fd1f5f7bd9509bbf8bd88
Added new global option (regcontext) to pjsip. When set, Asterisk will
dynamically create and destroy a NoOp priority 1 extension
for a given endpoint who registers or unregisters with us.
ASTERISK-25670 #close
Reported-by: Daniel Journo
Change-Id: Ib1530c5b45340625805c057f8ff1fb240a43ea62
Due to locking issues within pjnath these changes are being
reverted until pjnath can be changed.
ASTERISK-25645
Revert "res_rtp_asterisk.c: Fix DTLS negotiation delays."
This reverts commit 24ae124e4f.
Change-Id: I2986cfb2c43dc14455c1bcaf92c3804f9da49705
Revert "res_rtp_asterisk: Resolve further timing issues with DTLS negotiation"
This reverts commit 965a0eee46.
Change-Id: Ie68fafde27dad4b03cb7a1e27ce2a8502c3f7bbe
This reverts commit 0a9941de9d.
Matt,
This patch causes another problem and should not have been needed.
Before this patch, persistent_endpoint_contact_deleted_observer WAS
deleting the contact_status when ast_sip_location_delete_contact was
called. By deleting it yourself in ast_sip_location_delete_contact
it was gone before the observer could run and the observer therefore
was throwing an error and not sending stasis/AMI/statsd messages.
So, I don't think this was the cause of your original issue. I also
had verified the contact AMI and statsd lifecycle and it was working.
I'll double check now though.
ASTERISK-25675
Reported-by: Daniel Journo
Change-Id: Ib586a6b7f90acb641b0c410f659743ab90e84f1a
This change causes res_crypto to unregister CLI at shutdown while still
preventing the module from being unloaded.
ASTERISK-25673 #close
Change-Id: Ie5d57338dc2752abfc0dd05d0eec86413f2304fc
A deadlock was observed where the monitor thread was stuck, therefore
resulting in no incoming SIP traffic being processed.
The problem occurred when two 200 OK responses arrived in response to a
terminating NOTIFY request sent from Asterisk. The first 200 OK was
dispatched to a threadpool worker, who locked the corresponding
transaction. The second 200 OK arrived, resulting in the monitor thread
locking the dialog. At this point, the two threads are at odds, because
the monitor thread attempts to lock the transaction, and the threadpool
thread loops attempting to try to lock the dialog.
In this case, the fix is to not have the monitor thread attempt to hold
both the dialog and transaction locks at the same time. Instead, we
release the dialog lock before attempting to lock the transaction.
There have also been some debug messages added to the process in an
attempt to make it more clear what is going on in the process.
ASTERISK-25668 #close
Reported by Mark Michelson
Change-Id: I4db0705f1403737b4360e33a8e6276805d086d4a
The menuselect conflict between app_voicemail and res_mwi_external
makes it hard to package 1 version of Asterisk. There no actual
build dependencies between the 2 so moving this check to runtime
seems like a better solution.
The ast_vm_register and ast_vm_greeter_register functions in app.c
were modified to return AST_MODULE_LOAD_DECLINE instead of -1 if there
is already a voicemail module registered. The modules' load_module
functions were then modified to return DECLINE instead of -1 to the
loader. Since -1 is interpreted by the loader as AST_MODULE_LOAD_FAILURE,
the modules were incorrectly causing Asterisk to stop so this needed
to be cleaned up anyway.
Now you can build both and use modules.conf to decide which voicemail
implementation to load.
The default menuselect options still build app_voicemail and not
res_mwi_external but if both ARE built, res_mwi_external will load
first and become the voicemail provider unless modules.conf rules
prevent it. This is noted in CHANGES.
Change-Id: I7d98d4e8a3b87b8df9e51c2608f0da6ddfb89247
Updated ast_websocket_write to encode the entire frame in to one
write operation, to ensure that we don't end up with a situation
where the websocket header has been sent, while the body can not
be written.
Previous to August's patch in commit b9bd3c14, certain network
conditions could cause the header to be written, and then the
sub-sequent body to fail - which would cause the next successful
write to contain a new header, and a new body (resulting in
the peer receiving two headers - the second of which would be
read as part of the body for the first header).
This was patched to have both write operations individually fail
by closing the websocket.
In a case available to the submitter of this patch, the same
body which would consistently fail to write, would succeed
if written at the same time as the header.
This update merges the two operations in to one, adds debug messages
indicating the reason for a websocket connection being closed during
a write operation, and clarifies some variable names for code legibility.
Change-Id: I4db7a586af1c7a57184c31d3d55bf146f1a40598
This patch adds a new module, res_pjsip_history, that provides a slightly
better way of debugging SIP message traffic on a busy Asterisk system. The
existing mechanisms all rely on passively dumping a SIP message to the CLI.
While this is perfectly fine for logging purposes and well controlled
environments, on many installations, the amount of SIP messages Asterisk
receives will quickly swamp the CLI. This makes it difficult to view/capture
those messages that you want to diagnose in real time.
This patch provides another way of handling this. When enabled, the module
will store SIP message traffic in memory. This traffic can then be queried
at leisure.
In order to make the querying useful, a CLI command has been implemented,
'pjsip show history', that supports a basic expression syntax similar to
SQL or other query languages. A small number of useful fields have been
added in this initial patch; additional fields can easily be added in
later improvements. Those fields are:
- number: The entry index in the history
- timestamp: The time the message was recieved
- addr: The source/destination address of the message
- sip.msg.request.method: The request method
- sip.msg.call-id: The Call-ID header
Note - this is a resurrection of the module initially proposed on Review Board
here: https://reviewboard.asterisk.org/r/4053/
Change-Id: I39bd74ce998e99ad5ebc0aab3e84df3a150f8e36
In 450579e908, a change was made that removed the deletion of the
'contact_status' object when a 'contact' object is deleted in sorcery.
This unfortunately means that the 'contact_status' object persists, even when
something has explicitly removed a contact. The result is that the state of
the contact will not be regenerated if that contact is re-created, and the
stale state will be reported/used for that contact. It also results in
no ContactStatusChanged events being generated for either ARI or AMI.
This patch restores the deletion logic that was removed. Doing so now
results in the expected events being generated again.
Change-Id: I28789a112e845072308b5b34522690e3faf58f07
Resolves an edge case dtls negotiation delay for certain networks which
somehow manage to drop the rtcp side's packet when these are both sent
ast_rtp_remote_address_set, causing it to have to time-out and restart
the handshake.
Move dtls pending bio flush in to it's own function, and call it from
ast_rtp_on_ice_complete, when we're rtp->ice, rather than when
ast_rtp_remote_address_set.
Keep the existing flush from the recent change to res_rtp_remote_address_set
if ice is not being used.
ASTERISK-25614 #close
Reported-by: XenCALL
Tested by: XenCALL
Change-Id: Ie2caedbdee1783159f375589b6fd3845c8577ba5
This change introduces the configuration option 'full_backend_cache'
which changes the cache to be a full mirror of the backend instead
of a per-object cache. This allows all sorcery retrieval operations
to be carried out against it and is useful for object types which
are used in a "retrieve all" or "retrieve some" pattern.
ASTERISK-25625 #close
Change-Id: Ie2993487e9c19de563413ad5561c7403b48caab5
The JSON library Asterisk uses, jansson, is not thread
safe for us in a few ways. To help with this wrappers for JSON
object reference count increasing and decreasing were added
which use a global lock to ensure they don't clobber over
each other. This does not extend to reference count manipulation
within the jansson library itself. This means you can't safely
use the object borrowing specifier (O) in ast_json_pack and
you can't share JSON instances between objects.
This change removes uses of the O specifier and replaces them
with the o specifier and an explicit ast_json_ref. Some cases
of instance sharing have also been removed.
ASTERISK-25601 #close
Change-Id: I06550d8b0cc1bfeb56cab580a4e608ae4f1ec7d1
- Trigger pending DTLS packets to send out, once the RTP instance's remote
address is set.
- Avoids locking the DTLS structure unnecessarily by only doing this if
DTLS is passive.
- Add DTLS locks around the structurally sensitive calls in the SSL
portion of __rtp_recvfrom, since dtls_srtp_check_pending does not lock
inside of itself, and we're dealing with the SSL BIO in at least two
threads.
WebRTC channels may receive a DTLS handshake before
ast_rtp_remote_address_set is called, which causes there to be a pending
response to send out. Previous to 1ad827, this was handled by calling
dtls_srtp_check_pending on receipt of any RTP packet - a STUN or RTP
packet could trigger the pending handshake response. Since that was
rightfully removed, whenever the DTLS handshake is received before the
remote address is set, we would have to wait until another SSL packet
arrives.
As of Chrome M47's optimizations to their handshake process, WebRTC
conversations between Chrome M47+ and Asterisk, where Asterisk is passive,
experience a 1 second delay without this patch, because the SSL handshake
is received before ICE negotation stores the remote_address, and the next
SSL packet isn't received until after a 1 second timeout in Chrome, which
causes a new handshake request.
ASTERISK-25614 #close
Change-Id: I547f1be7e302dbf71f6553dd8cbc0657b1d0b908
pjproject < 2.5.0 will segfault on a tls transport if async_operations
is greater than 1. A runtime version check has been added to throw
an error if the version is < 2.5.0 and async_operations > 1.
To assist in the check, a new api "ast_compare_versions" was added
to utils which compares 2 major.minor.patch.extra version strings.
ASTERISK-25615 #close
Change-Id: I8e88bb49cbcfbca88d9de705496d6f6a8c938a98
Reported-by: George Joseph
Tested-by: George Joseph
Fixed a bug that originally would show a negative number of
active calls occuring in Asterisk. A gauge is persistent so
incrementing and decrementing it results in a more consistent
performance. Also changed to the call to StatsD to use
ast_statsd_log_string() so that a "+" could be sent to StatsD.
ASTERISK-25619 #close
Change-Id: Iaaeff5c4c6a46535366b4d16ea0ed0ee75ab2ee7
Both transport and endpoint now check for the existence and readability
of tls certificate and key files before passing them on to pjproject.
This will cause the object to not load rather than waiting for pjproject
to discover that there's a problem when a session is attempted.
NOTE: chan_sip also uses ast_rtp_dtls_cfg_parse but it's located
in build_peer which is gigantic and I didn't want to disturb it.
Error messages will emit but it won't interrupt chan_sip loading.
ASTERISK-25618 #close
Change-Id: Ie43f2c1d653ac1fda6a6f6faecb7c2ebadaf47c9
Reported-by: George Joseph
Tested-by: George Joseph
See ASTERISK-25615.
If the transport protocol is tls and async_operations > 1, pjproject
will segfault if more than one operation is attempted on the same socket.
Until this is fixed upstream, a check has been added to throw an error
if a tls transport config has async_operations set to > 1.
ASTERISK-25615
Change-Id: I76b9a5b2a5a0054fe71ca5851e635f2dca7685a6
Reported-by: George Joseph
Tested-by: George Joseph
It will never be perfect or even pretty, mostly because of the differences
between static and dynamic contacts.
Created:
Can't use the contact or contact_status alloc functions
because the objects come and go regardless of the actual state.
Can't use the contact_apply_handler, ast_sip_location_add_contact or
a sorcery created handler because they only get called for dynamic
contacts. Similarly, permanent_uri_handler only gets called for
static contacts.
So, Matt had it right. :) ast_res_pjsip_find_or_create_contact_status is
the only place it can go and not have duplicated code. Both
permanent_uri_handler and contact_apply_handler call find_or_create.
Removed:
Can't use the destructors for the same reason as above. The only
place to put this is in persistent_endpoint_contact_deleted_observer
which I believe is the "correct" place but even that will handle only
dynamic contacts. This doesn't called on shutdown however. There is
no hook to use for static contacts that may be removed because of a
config change while asterisk is in operation.
I moved the cleanup of contact_status from ast_sip_location_delete_contact
to the handler as well.
Status Change and RTT:
Although they worked fine where they were (in update_contact_status) I
moved them to persistent_endpoint_contact_status_observer to make it
more consistent with removed. There was logic there already to detect
a state change.
Finally, fixed a nit in permanent_uri_handler rmudgett reported
eralier.
ASTERISK-25608 #close
Change-Id: I4b56e7dfc3be3baaaf6f1eac5b2068a0b79e357d
Reported-by: George Joseph
Tested-by: George Joseph
Beside that, the format-attribute module sends only non-default values in the
line fmtp, now. This avoids unnecessary overhead in SDP messages. Furthermore,
previously the parameter stereo was not parsed when being the first parameter.
ASTERISK-25583 #close
Change-Id: Iae85ba3e5960bfd5d51cf65bcffad00dd4875a73
When 90d9a70789 was merged, it mostly tested dynamic contacts created as
a result of registering a PJSIP endpoint. Contacts generated in this
fashion typically have a long alphanumeric string as their object identifier,
which maps reasonably well for StatsD. Unfortunately, this doesn't work in the
general case. StatsD treats both '.' and ':' characters as special characters.
In particular, having a ':' appear in the middle of a StatsD metric will
result in the metric being rejected.
This causes some obvious issues with SIP URIs.
The StatsD API should not be responsible for escaping the metric name passed
to it. The metric is treated as a single long string, and it would be
challenging to know what to escape in the string passed to the function.
Likewise, we don't want to escape the metric in PJSIP, as that involves
overhead that is wasted when either res_statsd isn't loaded or enabled.
This patch takes an alternative approach. The Contact ID has been changed
to be "aor@@uri_hash" instead of "aor@@uri". This (a) won't contain any of the
aforementioned special characters, (b) can be done on Contact creation,
which has minimal impact on run-time performance, and (c) also conforms to an
earlier commit that changed the ID for dynamic contacts.
The downside of this is that StatsD users will have to map SHA1 hashes back to
the Contacts that are emitting the statistics. To that end, the CLI commands
have been updated to include the first 10 characters of the MD5 hash, which
should be enough to match what is shown in Graphite (or some other StatsD
backend).
ASTERISK-25595 #close
Change-Id: Ic674a3307280365b4a45864a3571c295b48a01e2
Reported-by: Matt Jordan
Tested-by: George Joseph
An earlier commit changed the id of dynamic contacts to contain
a hash instead of the uri. This patch updates status change
logging to show the aor/uri instead of the id. This required
adding the aor id to contact and contact_status and adding
uri to contact_status. The aor id gets added to contact and
contact_status in their allocators and the uri gets added to
contact_status in pjsip_options when the contact_status is
created or updated.
ASTERISK-25598 #close
Reported-by: George Joseph
Tested-by: George Joseph
Change-Id: I56cbec1d2ddbe8461367dd8b6da8a6f47f6fe511
The fastagi record-file testsuite test sometimes fails reporting an empty
recorded file. This was happening because Asterisk was sending the agi result
notification prior to actually closing the file and the data, being buffered,
had not been written to the file yet when the test attempts to check the file
size.
This patch makes it so the record file stream is closed prior to sending the
agi result notification.
ASTERISK-25593 #close
Change-Id: I6b2b3be3ae37f7c7b18e672c419a89b3b8513cde
The usage info for 'pjsip send notify' previously referenced the
chan_sip configuration sip_notify.conf. Fix this to reference
the correct configuration pjsip_notify.conf.
ASTERISK-25590 #close
Change-Id: I3898271a8e8a8b1db201741e790ebe2c6bf5cdea
If the sorcery object type is not found a NULL is returned.
Unfortunately, sorcery_realtime_filter_objectset() will crash after
complaining about not finding the object type and saying to expect errors.
* Use ao2_cleanup() instead of ao2_ref() to prevent the crash.
ASTERISK-25165
Reported by Corey Farrell
Change-Id: Ic3b64453ea3058cb68d5c26d97d4fe7b8eea2e97
When a channel is in a direct media bridge, a re-INVITE may arrive that forces
Asterisk to re-negotiate the media to a T.38 fax. When this occurs, the bridge
must change its technology to a simple bridge, and re-INVITE the media back
to Asterisk.
Generally, this logic mostly already exists in Asterisk. However, prior to this
patch, there were a few bugs:
(1) The T.38 framehook currently prevents a channel capable of T.38 faxes from
ever entering into a direct media bridge. This applies even when the only
media being passed over the channel is audio. This patch fixes this bug
by having the framehook specify that it defers caring about any frame type.
This allows the channels to enter into a direct media bridge, which will
be broken when a re-INVITE is received.
(2) When a re-INVITE is received, nothing instructed the bridging layer to
re-inspect the allowed bridging technology. This now occurs when either
a re-INVITE is received from a peer, or when a response is received from
the far end (that is, when the T.38 state changes to either
T38_PEER_REINVITE or T38_LOCAL_REINVITE).
(3) chan_pjsip needs to do a small amount of work to prevent a direct media
bridge from being chosen when a T.38 session is in progress. When a T.38
session supplement has a t38 datastore - which is added when we detect
we should start thinking about T.38 on a channel - we now refuse a native
RTP bridge.
(4) When a BYE request is received, we don't terminate the T.38 session. If
the other side of a T.38 fax survives the hangup (due to the 'g' flag
in Dial, for example), we don't currently re-INVITE the media on the
other channel back to audio. This patch now has res_pjsip_t38 intercept
BYE requests and inform the far side that the T.38 session is terminated.
This naturally causes the correct re-INVITEs to be sent.
ASTERISK-25582
Change-Id: Iabd6aa578e633d16e6b9f342091264e4324a79eb
Joshua Colp
snuffy
George Joseph
Matt Jordan
Sean Bright
zuul
Alexei Gradinari
Sebastian Damm
Kevin Harwell
Richard Mudgett
George Joseph
Mark Michelson
Jacek Konieczny
Philip Correia
Gianluca Merlo
Walter Doekes
Sergio Medina Toledo
Scott Griepentrog
Christof Lauber
Badalyan Vyacheslav
Karsten Wemheuer
Daniel Journo
Corey Farrell
Dade Brandon
server-pandora
tcambron
Alexander Traud
David M. Lee