Ability has been added to both manager command SIPnotify as well as console
command sip notify. Message body is stored in the "Content" variable. An
example is present in sip_notify.conf.
(closes issue #13926)
Reported by: jthurman
Patches:
sip-notify-svn189463.diff uploaded by gareth (license 208)
Tested by: gareth
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@224035 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds support for TCP/TLS in the Contact header when using
NAT, specifically externip or externhost. The original issue was that
Asterisk sent 5060 as the port in the contact header whether TLS was
used or not. Additionally, this patch adds 2 config options to sip.conf,
specifically externtcpport and externtlsport. This allows a user to
specify different external ports for TCP and TLS other than those used
internally, this is especially useful in in a PAT/port redirection setup.
Thanks to ebroad for reporting the issue and providing the patch!
(closes issue #15880)
Reported by: ebroad
Patches:
portmap.patch uploaded by ebroad (license 878)
externtXXport_v2.patch uploaded by ebroad (license 878)
Tested by: ebroad
Review: https://reviewboard.asterisk.org/r/392/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@222398 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Many T.38 endpoints incorrectly send the maximum IFP frame size they can accept
as the T38FaxMaxDatagram value in their SDP, when in fact this value is
supposed to be the maximum UDPTL payload size (datagram size) they can accept.
If the value they supply is small enough (a commonly supplied value is '72'),
T.38 UDPTL transmissions will likely fail completely because the UDPTL packets
will not have enough room for a primary IFP frame and the redundancy used for
error correction. If this occurs, the Asterisk UDPTL stack will emit log messages
warning that data loss may occur, and that the value may need to be overridden.
This patch extends the 't38pt_udptl' configuration option in sip.conf to allow
the administrator to override the value supplied by the remote endpoint and
supply a value that allows T.38 FAX transmissions to be successful with that
endpoint. In addition, in any SIP call where the override takes effect, a debug
message will be printed to that effect. This patch also removes the
T38FaxMaxDatagram configuration option from udptl.conf.sample, since it has not
actually had any effect for a number of releases.
In addition, this patch cleans up the T.38 documentation in sip.conf.sample
(which incorrectly documented that T.38 support was passthrough only).
(issue #15586)
Reported by: globalnetinc
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@222110 65c4cc65-6c06-0410-ace0-fbb531ad65f3
chan_sip has had the ability to control T.38 FAX error correction mode on a per-peer
(or global) basis for a couple of releases now, which is where it should have been
all along. This patch removes the ability to configure it in udptl.conf, but issues
a warning if the user tries to do, telling them to look at sip.conf.sample for how
to configure it now. For any SIP peers that are T.38 enabled in sip.conf, there is
already a default for FEC error correction even if the user does not specify any mode,
so this change will not turn off error correction by default, it will have the same
default value that has been in the udptl.conf sample file.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221592 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r221360 | mnicholson | 2009-09-30 14:36:06 -0500 (Wed, 30 Sep 2009) | 10 lines
Fix SRV lookup and Request-URI generation in chan_sip.
This patch adds a new field "portinuri" to the sip dialog struct and the sip peer struct. That field is used during RURI generation to determine if the port should be included in the RURI. It is also used in some places to determine if an SRV lookup should occur.
(closes issue #14418)
Reported by: klaus3000
Tested by: klaus3000, mnicholson
Review: https://reviewboard.asterisk.org/r/369/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221432 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r221086 | twilson | 2009-09-30 09:49:11 -0500 (Wed, 30 Sep 2009) | 25 lines
Change the SSRC by default when our media stream changes
Be default, change SSRC when doing an audio stream changes Asterisk doesn't
honor marker bit when reinvited to already-bridged RTP streams,resulting in
far-end stack discarding packets with "old" timestamps that areactually part of
a new stream. This patch sends AST_CONTROL_SRCUPDATE whenever there is a
reinvite, unless the 'constantssrc' is set to true in sip.conf.
The original issue reported to Digium support detailed the following situation:
ITSP <-> Asterisk 1.4.26.2 <-> SIP-based Application Server Call comes in
fromITSP, Asterisk dials the app server which sends a re-invite back
toAsterisk--not to negotiate to send media directly to the ITSP, but to
indicatethat it's changing the stream it's sending to Asterisk. The app
servergenerates a new SSRC, sequence numbers, timestamps, and sets the marker
bit on the new stream. Asterisk passes through the teimstamp of the new stream,
butdoes not reset the SSRC, sequence numbers, or set the marker bit.
When the timestamp on the new stream is older than the timestamp on the
originalstream, the ITSP (which doesn't know there has been any change) discards
the newframes because it thinks they are too old. This patch addresses this by
changing the SSRC on a stream update unless constantssrc=true is set in
sip.conf.
Review: https://reviewboard.asterisk.org/r/374/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221266 65c4cc65-6c06-0410-ace0-fbb531ad65f3
JABBER_RECEIVE (along with JabberSend) makes Asterisk interact with users over
XMPP to process calls.
SendText can be used instead of JabberSend in the context of XMPP based voice
channels (chan_gtalk and chan_jingle).
(closes issue #12569)
Reported by: eech55
Tested by: phsultan, asannucci, lmadsen, jtodd, maxgo
Review: https://reviewboard.asterisk.org/r/88/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@220457 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r216430 | oej | 2009-09-04 15:45:48 +0200 (Fre, 04 Sep 2009) | 27 lines
Make apps send PROGRESS control frame for early media and fix too early media issue in SIP
The issue at hand is that some legacy (dying) PBX systems send empty media frames on PRI
links *before* any call progress. The SIP channel receives these frames and by default
signals 183 Session progress and starts sending media. This will cause phones to
play silence and ignore the later 180 ringing message. A bad user experience.
The fix is twofold:
- We discovered that asterisk apps that support early media ("noanswer") did not send
any PROGRESS frame to indicate early media. Fixed.
- We introduce a setting in chan_sip so that users can disable any relay of media frames
before the outbound channel actually indicates any sort of call progress.
In 1.4, 1.6.0 and 1.6.1, this will be disabled for backward compatibility. In later versions
of Asterisk, this will be enabled. We don't assume that it will change your Asterisk
phone experience - only for the better.
We encourage third-party application developers to make sure that if they have applications
that wants to send early media, add a PROGRESS control frame transmission to make sure that
all channel drivers actually will start sending early media. This has not been the default
in Asterisk previous to this patch, so if you got inspiration from our code, you need to
update accordingly. Sorry for the trouble and thanks for your support.
This code has been running for a few months in a large scale installation (over 250
servers with PRI and/or BRI links to old PBX systems).
That's no proof that this is an excellent patch, but, well, it's tested :-)
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@216438 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Allows characters that are otherwise used as delimiters to be used within
certain fields (like the secret).
(closes issue #15008, closes issue #15672)
Reported by: tilghman
Patches:
20090818__issue15008.diff.txt uploaded by tilghman (license 14)
Tested by: lmadsen, tilghman
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@213098 65c4cc65-6c06-0410-ace0-fbb531ad65f3
It is clear from multiple mailing list, forum, wiki and other sorts of posts
that users don't really understand the effects that the 'canreinvite' config
option actually has, and that in some cases they think that setting it to 'no'
will actually cause various other features (T.38, MOH, etc.) to not work properly,
when in fact this is not the case. This patch changes the proper name of the
option to what it should have been from the beginning ('directmedia'), but
preserves backwards compatibility for existing configurations.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@210190 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r209131 | mmichelson | 2009-07-27 12:44:06 -0500 (Mon, 27 Jul 2009) | 18 lines
Allow for UDPTL to use only even-numbered ports if desired.
There are some VoIP providers out there that will not accept SDP
offers with odd numbered UDPTL ports. While it is my personal opinion
that these VoIP providers are misinterpreting RFC 2327, it really is
not a big deal to play along with their silly little games. Of course,
since restricting UDPTL ports to only even numbers reduces the range
of available ports by half, so the option to use only even port numbers
is off by default. A user can enable the behavior by setting
use_even_ports=yes in udptl.conf.
(closes issue #15182)
Reported by: CGMChris
Patches:
15182.patch uploaded by mmichelson (license 60)
Tested by: CGMChris
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@209132 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Requiring 'module reload' to reload everything, including
core etc makes russell very unhappy.
The default configuration already loads the 'friendly' aliases template.
Added 'reload=module reload' to that template.
Also removed the comment in main/cli.c that reload should come back.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@208813 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This is a continuation of revision 885 to LibPRI (Capture and expose the Reverse
Charging Indication IE on ISDN PRI) which added the ability to get/set Reverse
Charging Indication in LibPRI. This patch adds the ability to specify RCI on
the outbound leg of a PRI call from within Asterisk, by prefixing the dialed
number with a capital 'C' like:
...,Dial(DAHDI/g1/C4445556666)
And to read it off an inbound channel:
exten => s,1,Set(RCI=${CHANNEL(reversecharge)})
Thanks again to rmudgett for the thorough review.
(closes issue #13760)
Reported by: mrgabu
Review: https://reviewboard.asterisk.org/r/303/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204749 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Someone asked yesterday, "is there a good reason why we can't just put these
modules in Asterisk?". After a brief discussion, as long as the modules are
clearly set aside in their own directory and not enabled by default, it is
perfectly fine.
For more information about why a module goes in addons, see README-addons.txt.
chan_ooh323 does not currently compile as it is behind some trunk API updates.
However, it will not build by default, so it should be okay for now.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204413 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This might seem like a legitimate comment that merely needed semicolon
prefixes, but in reality, the adaptive layer is designed to allow arbitrary
CDR variables, without needing the use of a userfield to store multiple items.
It's therefore not only invalid syntax but also goes against the intent of the
adaptive method.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204069 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The original patch for this was written by Brett Bryant, and I split it out into
it's own module.
(closes issue #12876)
Reported by: bbryant
Patches:
06162008_cdr_custom_syslog.diff uploaded by bbryant (license 36)
05212009_cdr_syslog.patch uploaded by seanbright (license 71)
Tested by: seanbright
Review: https://reviewboard.asterisk.org/r/297/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203846 65c4cc65-6c06-0410-ace0-fbb531ad65f3
CEL is the new system for logging channel events. This was inspired after
facing many problems trying to represent what is possible to happen to a call
in Asterisk using CDR records. For more information on CEL, see the built in
HTML or PDF documentation generated from the files in doc/tex/.
Many thanks to Steve Murphy (murf) and Brian Degenhardt (bmd) for their hard
work developing this code. Also, thanks to Matt Nicholson (mnicholson) and
Sean Bright (seanbright) for their assistance in the final push to get this
code ready for Asterisk trunk.
Review: https://reviewboard.asterisk.org/r/239/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203638 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Also change the preferred configuration option from 'hostname' (which was
misleading because it didn't actually treat the value as a hostname) to
'connection' and added some verbage explaining that the user would need to
refer to their freetds.conf file for those settings. 'hostname' was kept
as a backwards compatible configuration parameter.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@202887 65c4cc65-6c06-0410-ace0-fbb531ad65f3
chan_sip has an option to save the sysname on rtupdate. This patch copies that same logic to chan_iax.
(closes issue #14837)
Reported by: barthpbx
Patches:
iax2-rtsavesysname.patch uploaded by barthpbx (license 744)
rt_iax.diff uploaded by dvossel (license 671)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@201534 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This code was there because of the AgentCallbackLogin() application.
->loginchan[] member was only used by AgentCallbackLogin().
Agent where dumped to astdb if they where logged in using AgentCallbacklogin()
so they are not being dumper anymore.
Review: https://reviewboard.asterisk.org/r/267/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@198217 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This commit add Calendaring support to Asterisk for iCalendar, CalDAV, and MS
Exchange calendars. Exchange support has only been tested on Exchange Server 2k3
and does not support forms-based authentication at this time (patches *very*
welcome). Exchange support is also currently missing the ability to return a
list of a meting's attendees (again, patches are very, very welcome).
Features include:
Querying a calendar for events over a specific time range
Checking a calendar's busy status via the dialplan
Writing calendar events via the dialplan (CalDAV and Exchange only)
Handling calendar event notifications through the dialplan
(closes issue #14771)
Tested by: lmadsen, twilson, Shivaprakash
Review: https://reviewboard.asterisk.org/r/58
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@197738 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Let's try that again, this time removing trailing whitespace and not leading
whitespace. I can't believe no one noticed.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@197535 65c4cc65-6c06-0410-ace0-fbb531ad65f3
In sip.conf the transport option allows for the configuration of what transport types (udp, tcp, and tls) a peer will accept, but only the first type listed was used for outbound connections. This patch changes this. Now the default transport type is only used until the peer registers. When registration takes place the transport type is parsed out of the Contact header. If the Contact header's transport type is equal to one that the peer supports, the peer's default transport type for outbound connections is set to match the Contact header's type. If the Contact header's transport type is not present, then the peer's default transport type is set to match the one the peer registered with. When a peer unregisters or the registration expires, the default transport type for that peer is reset.
(closes issue #12282)
Reported by: rjain
Patches:
reg_patch_1.diff uploaded by dvossel (license 671)
Tested by: dvossel
(closes issue #14727)
Reported by: pj
Patches:
reg_patch_3.diff uploaded by dvossel (license 671)
Tested by: pj, dvossel
Review: https://reviewboard.asterisk.org/r/249/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@196416 65c4cc65-6c06-0410-ace0-fbb531ad65f3
SIP purists may want to look the other way...
When COLP/CONP support for SIP was committed, there was a condition under
which Asterisk may transmit a SIP UPDATE in order to communicate the change
in connected line information. The issue here is that while we could send a
SIP UPDATE message, we were not prepared to receive such an UPDATE and would
always responde with a 501 when we received an UPDATE.
The situation was a bit rough. We really want to be able to receive UPDATEs
having to do with connected line changes, but the amount of effort involved
in properly supporting RFC 3311 was staggering. This commit represents a
compromise.
First, it was decided that it is important to only send a SIP UPDATE to
an endpoint that is able to handle one. So, now we have added parsing of
the Allow header into SIP. We store the allowed methods on SIP peers so
that when we communicate with them, we already will know what we can and
cannot send to them. We will parse the peer's allowed methods when he registers
with us. If the peer is not the type to register with us, but the qualify option
is enabled, then we will use the response to the OPTIONS request we send
the peer to determine the peer's allowed methods. When the peer's registration
expires, or when qualify deems the peer to be unreachable, we clear the allowed
methods from the peer.
For an actual call, we will copy the peer's allowed methods to the sip_pvt
representing the call leg. If we are communicating with an endpoint which is
not a peer, then we will just parse the Allow header from the first message
we receive during the call and store the information in the sip_pvt.
If, during communication with a peer, we receive a 501 response, then we will
make sure to save the fact that we cannot use that method when communicating
with that peer.
Now, with all that infrastructure in place, the only actual place we use this
information currently is when attempting to send a connected line change using
an UPDATE request. If we cannot send the change immediately using an UPDATE,
we will set the SIP_NEEDREINVITE flag so that we can send a REINVITE as soon
as it is allowed.
The second part of the changes here is for Asterisk to accept UPDATE requests
that have connected line changes. Since we are not fully supporting RFC 3311,
Asterisk will NOT place the UPDATE method in Allow headers it sends. Instead,
if you are communicating with what you know to be another Asterisk box, you may
set the rpid_update parameter in sip.conf so that we will send UPDATEs to that
Asterisk box. When we send a connected line update, we set a custom header
called "X-Asterisk-rpid-update."
On the receiving end, if Asterisk receives an UPDATE that does not have the
"X-Asterisk-rpid-update" header present, then Asterisk will respond with a 501
since media-changing UPDATEs are not supported. We should never get such
UPDATEs, since as was stated earlier, Asterisk does not put UPDATE in its Allow
header. If the custom header is present in the received UPDATE, though, then we
will check the incoming request for connected line updates and queue the update
on the channel where the change occurred.
ABE-1840
ABE-1822
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@195589 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Up to now, cdr_custom would only accept a single filename/format from
cdr_custom.conf. This change allows you to specify multiple filename
& format directives.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@195165 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Select what to do with outgoing COLP information on this port.
0 - Send out COLP information unaltered. (default)
1 - Force COLP to restricted on all outgoing COLP information.
2 - Do not send COLP information.
outgoing_colp=0
Also fixed sending the EctInform message so it always has the
required redirectionNumber parameter when the status is active.
JIRA ABE-1853
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@194479 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r193193 | kpfleming | 2009-05-08 09:03:28 -0500 (Fri, 08 May 2009) | 7 lines
Make absolute paths for logger channels work properly
(Note: This is not a new feature, it was previously undocumented and broken.)
The Asterisk logger has a feature to support absolute pathnames for logger channels, but the code implementing the feature was broken. This has been fixed, and the absolute path feature is now documented in the sample logger.conf.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@193194 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This configuration file was changed to ensure that only one console channel driver
(chan_oss) is loaded by default, but the change would only work if chan_console
was not built. Now it will work as expected; if chan_alsa or chan_console are built
and installed, they will not be loaded unless explicity requested.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@191955 65c4cc65-6c06-0410-ace0-fbb531ad65f3
In discussions today at the Europe Asterisk Developer Meet-Up, we determined that
the event_log was used in only 9 places in the entire tree, and really was not needed
at all. The users have been converted to use LOG_NOTICE, or the messages have been
removed since other messages were already in place that provided the same information.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@191785 65c4cc65-6c06-0410-ace0-fbb531ad65f3
chan_sip allows for outbound TLS connections, but does not allow the user to specify what protocol to use (default was SSLv2, and still is if this new option is not specified). This patch lets the user pick the SSL/TLS client method for outbound connections in sip.
(closes issue #14770)
Reported by: TheOldSaint
(closes issue #14768)
Reported by: TheOldSaint
Review: http://reviewboard.digium.com/r/240/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@191177 65c4cc65-6c06-0410-ace0-fbb531ad65f3
ast_tls_read_conf() is a new api call for handling SSL/TLS options across all conf files. Before this change, SSL/TLS options were not consistent. http.conf and manager.conf required the 'ssl' prefix while sip.conf used options with the 'tls' prefix. While the options had different names in different conf files, they all did the exact same thing. Now, instead of mixing 'ssl' or 'tls' prefixes to do the same thing depending on what conf file you're in, all SSL/TLS options use the 'tls' prefix. For example. 'sslenable' in http.conf and manager.conf is now 'tlsenable' which matches what already existed in sip.conf. Since this has the potential to break backwards compatibility, previous options containing the 'ssl' prefix still work, but they are no longer documented in the sample.conf files. The change is noted in the CHANGES file though.
Review: http://reviewboard.digium.com/r/237/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@191028 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Adds option to specify a private key .pem file when configuring TLS or SSL in AMI, HTTP, and SIP. Before this, the certificate file was used for both the public and private key. It is possible for this file to hold both, but most configurations allow for a separate private key file to be specified. Clarified in .conf files how these options are to be used. The current conf files do not explain how the private key is handled at all, so without knowledge of Asterisk's TLS implementation, it would be hard to know for sure what was going on or how to set it up.
Review: http://reviewboard.digium.com/r/234/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@190545 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This is the companion commit to libpri r732. Service messages are now supported
for switch types 4ess/5ess. A new option service_message_support has been added
to chan_dahdi.conf and is noted in the sample config file. The service message
support is turned off by default. The current implementation relies on AstDB
to keep track of channel state, which allows the statuses to be preserved
across Asterisk restarts. Below is a description of the storage format.
The state and reason for the service state are in the form <state>:<reason>,
where:
<state> ::= { 'O' } // 'O' – Out Of Service
<reason> ::= { '0' | '1' | '2' | '3' }, where:
'0' – No reason (backwards compatibility)
'1' – NEAR END
'2' – FAR END
'3' – both NEAR and FAR END
The new CLI commands to handle channel service state are:
pri service disable channel <chan>
pri service enable channel <chan>
Many people contributed to the development of this functionality. Because I
entered at the very end I do not know the exact history. Special thanks to
all who moved the bug forward one way or another:
cmaj, PCadach, markster, mattf, drmac, MikeJ, serge-v, murf, kanelbullar, Seb7,
tilghman, lmadsen, and especially dhubbard (he answered lots of my questions
and did a large portion of the work)
(closes issue #3450)
Reported by: cmaj
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@188342 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This allows for you to change the From header for outgoing MWI
NOTIFY requests. Prior to this, the best you could do was to
set a callerid in the general section of sip.conf. The problem
was that this was used for all outbound requests, not just
MWI NOTIFY requests.
AST-201
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@187560 65c4cc65-6c06-0410-ace0-fbb531ad65f3
(inspired by this evening's Toronto Asterisk Users Group meeting and previous dicussions amongst various community members)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@187269 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The channel drivers which have been most heavily tested with these enhancements are
chan_sip and chan_misdn. Further work is being done to add Q.SIG support and will be
introduced in a later commit. chan_skinny has code added to it here, but according
to user pj, the support on chan_skinny is not working as of now. This will be fixed in
a later commit.
A special thanks goes out to bugtracker user gareth for getting the ball rolling and
providing the initial support for this work. Without his initial work on this, this would
not have been nearly as painless as it was.
This functionality has been tested by Digium's product quality department, as well as a
customer site running thousands of calls every day. In addition, many many many many bugtracker
users have tested this, too.
(closes issue #8824)
Reported by: gareth
Review: http://reviewboard.digium.com/r/201
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@186525 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This API provides a generic way for multiple RTP stacks to be
integrated into Asterisk. Right now there is only one present, res_rtp_asterisk,
which is the existing Asterisk RTP stack. Functionality wise this commit
performs the same as previously. API documentation can be viewed in the
rtp_engine.h header file.
Review: http://reviewboard.digium.com/r/209/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@186078 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This commit introduces official support for R2 signaling in chan_dahdi. The
modifications to chan_dahdi, and the supporting library, LibOpenR2, were both
written by Moises Silva.
Many users are using this code, or a variant of it, in Asterisk 1.2, 1.4 and 1.6
in Brazil, México and Argentina. An unknown number of users (but at least 1)
are using it in each of the following countries: Colombia, Nepal, Thailand,
Venezuela, Perú, and probably others.
To use this code, LibOpenR2 must be installed from http://www.libopenr2.org/.
Information about configuration can be found in configs/chan_dahdi.conf.sample.
The code committed is the most up to date version, which was being maintained
in svn/asterisk/team/moy/mfcr2/.
I would also like to include a Thank You to the many others that tested this
code beyond those listed in this commit message. These are the names that I
could find in the mantis issue.
(closes issue #12509)
Reported by: moy
Patches:
chan_zap-mfr2.patch uploaded by moy (license 222)
Tested by: moy, korihor, viniciusfontes, Skarmeth, loloski, asbestoshead, titogarrido, heliocoelhojr, konsultex, ncorrare, ecarruda, rtorresduque, PTorres, ychen
Review: http://reviewboard.digium.com/r/40/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@182355 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r180380 | mmichelson | 2009-03-05 12:58:48 -0600 (Thu, 05 Mar 2009) | 25 lines
Fix broken mailbox parsing when searchcontexts option is enabled.
When using the searchcontexts option in voicemail.conf, the code
made the assumption that all mailbox names defined were unique across
all contexts. However, the code did nothing to actually enforce this
assumption, nor did it do anything to alert a user that he may have
created an ambiguity in his voicemail.conf file by defining the same
mailbox name in multiple contexts.
With this change, we now will issue a nice long warning if searchcontexts
is on and we encounter the same mailbox name in multiple contexts and ignore
any duplicates after the first box. Whether searchcontexts is enabled or not,
if we come across a duplicate mailbox in the same context, then we will issue
a warning and ignore the duplicated mailbox. I have also added a small note
to voicemail.conf.sample in the explanation for searchcontexts explaining
that you cannot define the same mailbox in multiple contexts if you have
enabled the option.
(closes issue #14599)
Reported by: lmadsen
Patches:
14599.patch uploaded by mmichelson (license 60) (with slight modification)
Tested by: lmadsen
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@180383 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When the subscription context for a call pickup subscription differs
from the context of the call pickup target, there's not an easy way
to divine what context should be used for the pickup. The way to work
around this is to use PICKUPMARK as the context for the pickup.
This has been documented in the sip.conf.sample file
(ABE-1708)
closes issue #14567
submitted by: alecdavis
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@180155 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r180006 | mmichelson | 2009-03-03 16:48:18 -0600 (Tue, 03 Mar 2009) | 17 lines
Clarify some documentation of queues.conf.sample
It had always been possible to explicitly specify a "blank"
value for a sound file in queues.conf and have no sound played
back. The problem with this is that it would result in some ugly
CLI warnings from file.c.
This commit introduces a check when playing a file in app_queue
to see if the name of the file is zero-length and return early if
that is the case. Also, the ability to specify the blank sound
files in queues.conf is now mentioned more clearly in queues.conf.sample
(closes issue #14227)
Reported by: caspy
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@180007 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
In this case, it's just a matter of reducing the default timeouts from 2000
to 1000 msec, as the max def feature digit timeout is no longer halved.
........
r178956 | murf | 2009-02-26 14:27:32 -0700 (Thu, 26 Feb 2009) | 18 lines
This change moves the default feature digit timeout to 1000 ms from the previous default of 500.
As per bug 14515, a dev discussion arrived at a "mediated concensus"
of a default feature digit timeout of 1.0 sec. Some voted for 1300;
ctooley thought 1500 for distracted phone users in phone booths;
kpfleming put his foot down at 1.0 sec.
Users who found the previous default max delay of 250 msec perfect,
are welcome to override the new default. Notice that I said that
250 msec was the default; wait a minute, you might say, the config
file said it was 500 msec!; well, because of the bug fix for 14515,
we found that 500 msec was actually enforcing a max of 250. The bug
fix would restore 500 msec, but we felt even that was a bit tight
for most users... 2000 msec was pushed earlier by mmichelson, so
that reduces to 1000 msec after the bug fix. Enjoy!
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@178986 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Jeff Peeler
David Vossel
Olle Johansson
Jason Parker
Kevin P. Fleming
Matthew Nicholson
Matthias Nick
Terry Wilson
Philippe Sultan
Tilghman Lesher
Richard Mudgett
Mark Michelson
Michiel van Baak
Sean Bright
Ryan Brindley
Russell Bryant
Joshua Colp
Moises Silva
Eliel C. Sardanons
Gavin Henry
TransNexus OSP Development
Steve Murphy