asterisk

Commit Graph

Author	SHA1	Message	Date
Matt Jordan	78960975f2	pjproject/patches/config_site: Increase the max number of ICE candidates When negotiating ICE candidates with WebRTC capable endpoints, many networks will result in a browser offering ICE candidates that exceeds the default number of max candidates, 16. This patch bumps the max candidates to 32, with the max checks at twice the number of candidates. In practice, this has shown to be sufficient for browser/WebRTC negotiation. Change-Id: Ifd8da8b315f5ae14814d4ce20e10d2e6355020e5	9 years ago
George Joseph	6a568bcc66	res_pjsip_pubsub: Address SEGV when attempting to terminate a subscription Occasionally under load we'll attempt to send a final NOTIFY on a subscription that's already been terminated and a SEGV will occur down in pjproject's evsub_destroy function. This is a result of a race condition between all the paths that can generate a notify and/or destroy the underlying pjproject evsub object: * The client can send a SUBSCRIBE with Expires: 0. * The client can send a SUBSCRIBE/refresh. * The subscription timer can expire. * An extension state can change. * An MWI event can be generated. * The pjproject transaction timer (timer_b) can expire. Normally when our pubsub_on_evsub_state is called with a terminate, we push a task to the serializer and return at which point the dialog is unlocked. This is usually not a problem because the task runs immediately and locks the dialog again. When the system is heavily loaded though, there may be a delay between the unlock and relock during which another event may occur such as the subscription timer or timer_b expiring, an extension state change, etc. These may also cause a terminate to be processed and if so, we could cause pjproject to try to destroy the evsub structure twice. There's no way for us to tell that the evsub was already destroyed and the evsub's group lock can't tolerate this and SEGVs. The remedy is twofold. * A patch has been submitted to Teluu and added to the bundled pjproject which adds add/decrement operations on evsub's group lock. * In res_pjsip_pubsub: * configure.ac and pjproject-bundled's configure.m4 were updated to check for the new evsub group lock APIs. * We now add a reference to the evsub group lock when we create the subscription and remove the reference when we clean up the subscription. This prevents evsub from being destroyed before we're done with it. * A state has been added to the subscription tree structure so termination progress can be tracked through the asyncronous tasks. * The pubsub_on_evsub_state callback has been split so it's not doing double duty. It now only handles the final cleanup of the subscription tree. pubsub_on_rx_refresh now handles both client refreshes and client terminates. It was always being called for both anyway. * The serialized_on_server_timeout task was removed since serialized_pubsub_on_rx_refresh was almost identical. * Missing state checks and ao2_cleanups were added. * Some debug levels were adjusted to make seeing only off-nominal things at level 1 and nominal or progress things at level 2+. ASTERISK-26099 #close Reported-by: Ross Beer. Change-Id: I779d11802cf672a51392e62a74a1216596075ba1	9 years ago
George Joseph	e8abfdcdc5	pjproject_bundled: Move to pjproject 2.5 Although all the patches we had against 2.4.5 were applied by Teluu, a new bug was introduced preventing re-use of tcp and tls transports This patch removes all the previous patches against 2.4.5, updates the version to 2.5, and adds a new patch to correct the transport re-use problem. Change-Id: I0dc6c438c3910f7887418a5832ca186aea23d068	9 years ago
George Joseph	2a7130b8b0	pjproject_bundled: Check for python-dev and TEST_FRAMEWORK The pjsua and pjsystest apps are now built only if TEST_FRAMEWORK is set. The python bindings are now built only if TEST_FRAMEWORK is set and a python development package is installed. libresample was also disabled. ASTERISK-25993 #close Reported-by: Joshua Colp Change-Id: If4e91c503a02f113d5b71bc8b972081fa3ff6f03	9 years ago
George Joseph	f39089f17c	pjproject_bundled: Various fixes discovered during testing of OSes For all OSes: * Disabled third-party codecs in pjproject and added '--disable-speex-codec --disable-speex-aec --disable-gsm-codec' to the configure options since we don't use the pjsip codec capability. FreeBSD: * Added FreeBSD support to install_prereq. * Changed pjproject/configure.m4 to use $GNU_MAKE instead of hardcoding "make". * Added __progname and environ to asterisk.exports.in. * Reverted the use of ldconfig to create shared library symlinks to ln. * Only enable epoll in pjproject if `uname -s` is Linux. * Added a patch to pjproject to take the name of the 'make' command from an environment variable if supplied. This is needed for the python bindings. (merged by Teluu into pjproject trunk 5/3/2016) FreeBSD support isn't complete. Still some general issues regarding make/gmake having nothing to do with pjproject. With some handholding it DOES build successfully. CentOS: Added 'patch' and 'bzip2' to install_prereq PACKAGES_RH. CentOS 6/7 32/64 build and run the pjsip testsuite successfully. Ubuntu: No changes required. Ubuntu 15/16 32/64 build and run the pjsip testsuite successfully. Debian: No changes required. Debian 6/7/8 32/64 build and run the pjsip testsuite successfully. There will utimately be a follow-up patch to create an install_prereq for the testsuite as I've discovered a few missing requirements. ASTERISK-25968 #close Change-Id: I5756a07facfc63798115a5e73a8709382fe9259c	9 years ago
George Joseph	719ece5659	pjproject_bundled: Disable PJSIP_UNESCAPE_IN_PLACE When pjsip_parse_uri is called with PJSIP_UNESCAPE_IN_PLACE enabled, the input uri string will become corrupted if it contains escape sequences. It's not possible to automatically strdup or strdupa the input string because the output uri pj_str_t's will have pointers to chunks of the input string. Getting around this would require more memory management code and wouldn't be worth the savings of doing the unescape in place. ASTERISK-25970 #close Reported-by: Dmitriy Serov Change-Id: I28dc0e599b5108f7959b9c46dc8278371b372f88	9 years ago
George Joseph	cf15a2f2d3	pjproject: Add patch for removing strip of '[]' from header params From the patch submitted to Teluu on 4/12/2016 <<<<<<<<< The wholesale stripping of '[]' from header parameters causes issues if something (like a port) occurs after the final ']'. '[2001🅰️:b]' will correctly parse to '2001🅰️:b' '[2001🅰️:b]:8080' will correctly parse to '2001🅰️:b' but the scanner is left with ':8080' and parsing stops with a syntax error. I can't even find a case where stripping the '[]' is a good thing anyway. Even if you continued to parse and resulted in a string that looks like this... '2001🅰️🅱️8080', it's not valid. This came up in Asterisk because Kamailio sends us a Contact with an alias URI parameter that has an IPv6 address in it like this: Contact: <sip:1171@127.0.0.1:5080;alias=[2001:1:2::3]~43691~6> which should be legal but causes a syntax error because of the characters after the final ']'. Even if it didn't, the '[]' should still not be stripped. I've run the Asterisk Test Suite for PJSIP (252 tests) many of which are IPv6 enabled. No issues were caused by removing the code that strips the '[]'. >>>>>>>>>>> ASTERISK-25123 #close Reported-by: Anthony Messina Change-Id: I5cb33f4ebf07ee1f2b26d07caae715e2ec65595a	9 years ago
George Joseph	0c414eaf35	pjproject: Add patch to fix Via IPv6 parsing There's a bug in pjproject's sip_parser where the ":" wasn't correctly interpreted. This is causing IPv6 addresses in the "received" parameter of the Via header to cause a syntax check failure. This patch was submitted to Teluu on 4/10/2016. ASTERISK-25910 #close Reported-by: Anthony Messina Change-Id: Ic7e4c4aa14ded61860401ec349f5177568c4d922	9 years ago
George Joseph	d963a33749	pjproject-bundled: Cleanups for reported issues PortAudio should no longer be required PJSIP_MAX_PKT_LEN is now 6000 Older autoconf issue fixed. (CentOS 6) Change-Id: I463fa9586cbe7c6b3b603289f535bd8e361611dd	9 years ago
zuul	6186306852	Merge "pjproject: Pass (dont_)optimize flags to pjproject and fix pjsua" into 13	9 years ago
Joshua Colp	677a65fcbb	build: Add configure check for proto field of PJSIP TLS transport setting. Older versions of PJSIP do not have the proto field on the TLS transport setting structure. This change adds a configure check so even if it is not present we will still be able to build. Change-Id: Ibf3f47befb91ed1b8194bf63888baa6fee05aba9	9 years ago
George Joseph	38499e7125	pjproject: Pass (dont_)optimize flags to pjproject and fix pjsua The pjproject Makefile now uses the Asterisk optimization flags which are determined by the setting of the DONT_OPTMIZE menuselect flag. The Makefile was also restructured so a change to the top level menuselect.makeopts will result in a rebuild of pjproject. Also, "--disable-resample" was removed from the pjproject configure options. Without resample, pjsua (which is used by the testsuite) can't make audio calls. When it can't, it segfaults. Change-Id: I24b0a4d0872acef00ed89b3c527a713ee4c2ccd4	9 years ago
George Joseph	875d5e9872	pjproject_bundled: Remove --with-external-pa from configure options. Not sure why it was there in the first place as we already specify --disable-sound. Change-Id: Ia80a40e8b1e1acc287955ab11ba1fbd0c7d4cff9	9 years ago
George Joseph	7cf7b0a4f9	third_party/Makefile.rules: Replace unsupported != operator with $(shell ...) Apparently the != operator is fairly new so I've replaced it with the old $(shell ...) syntax. Change-Id: I16b2e1878a4f91e7e9740abd427f9639f933c479 Reported-by: Richard Mudgett	9 years ago
George Joseph	b59956a875	build-system: Allow building with static pjproject Background here: http://lists.digium.com/pipermail/asterisk-dev/2016-January/075266.html From CHANGES: * To help insure that Asterisk is compiled and run with the same known version of pjproject, a new option (--with-pjproject-bundled) has been added to ./configure. When specified, the version of pjproject specified in third-party/versions.mak will be downloaded and configured. When you make Asterisk, the build process will also automatically build pjproject and Asterisk will be statically linked to it. Once a particular version of pjproject is configured and built, it won't be configured or built again unless you run a 'make distclean'. To facilitate testing, when 'make install' is run, the pjsua and pjsystest utilities and the pjproject python bindings will be installed in ASTDATADIR/third-party/pjproject. The default behavior remains building with the shared pjproject installation, if any. Building: All you have to do is include the --with-pjproject-bundled option on the ./configure command line (and remove any existing --with-pjproject option if specified). Everything else is automatic. Behind the scenes: The top-level Makefile was modified to include 'third-party' in the list of MOD_SUBDIRS. The third-party directory was created to contain any third party packages that may be needed in the future. Its Makefile automatically iterates over any subdirectories passing on targets. The third-party/pjproject directory was created to house the pjproject source distribution. Its Makefile contains targets to download, patch configure, generate dependencies, compile libs, apps and python bindings, sanitized build.mak and generate a symbols list. When bootstrap.sh is run, it automatically includes the configure.m4 file in third-party/pjproject. This file has a macro to download and conifgure pjproject and get and set PJPROJECT_INCLUDE, PJPROJECT_DIR and PJPROJECT_BUNDLED. It also tests for the capabilities like PJ_TRANSACTION_GRP_LOCK by parsing preprocessor output as opposed to trying to compile. Of course, bootstrap.sh is only run once and the configure file is incldued in the patch. When configure is run with the new options, the macro in configure.m4 triggers the download, patch, conifgure and tests. No compilation is performed at this time. The downloaded tarball is cached in /tmp so it doesn't get downloaded again on a distclean. When make is run in the top-level Asterisk source directory, it will automatically descend all the subdirectories in third_party just as it does for addons, apps, etc. The top-level Makefile makes sure that the 'third-party' is built before 'main' so that dependencies from the other directories are built first. When main does build, a new shared library (libasteriskpj) is created that links statically to the pjproject .a files and exports all their symbols. The asterisk binary links to that, just as it does with libasteriskssl. When Asterisk is installed, the pjsua and pjsystest apps, and the pjproject python bindings are installed in ASTDATADIR/third-party/pjproject. This will facilitate testing, including running the testsuite which will be updated to check that directory for the pjsua module ahead of the system python library. Modules should continue to depend on pjproject if they use pjproject APIs directly. They should not care about the implementation. No changes to any res_pjsip modules were made. Change-Id: Ia7a60c28c2e9ba9537c5570f933c1ebcb20a3103	9 years ago

15 Commits (65d0c0beb12e28df23532a80b6fa8300b83da39c)