An earlier patch blocked the ast_bridge_impart() call until the channel
either entered the target bridge or it failed. Unfortuantely, if the
target bridge is stasis and the imprted channel is not a stasis channel,
stasis bounces the channel out of the bridge to come back into the bridge
as a proper stasis channel. When the channel is bounced out, that
released the block on ast_bridge_impart() to continue. If the impart was
a result of a transfer, then it became a race to see if the swap channel
would get hung up before the imparted channel could come back into the
stasis bridge. If the imparted channel won then everything is fine. If
the swap channel gets hung up first then the transfer will fail because
the swap channel is leaving the bridge.
* Allow a chain of ast_bridge_impart()'s to happen before any are
unblocked to prevent the race condition described above. When the channel
finally joins the bridge or completely fails to join the bridge then the
ast_bridge_impart() instances are unblocked.
ASTERISK-25947
Reported by: Richard Mudgett
ASTERISK-24649
Reported by: John Bigelow
ASTERISK-24782
Reported by: John Bigelow
Change-Id: I8fef369171f295f580024ab4971e95c799d0dde1
We have to setup the channel roles after the bridge class push is called
because the bridge class push callback may have set roles on the incoming
channel. Since we have already partially pushed the channel into the
bridge and reversing what we have already done could be problematic, the
only thing we can do is press on to complete pushing the channel into the
bridge.
* Ignore any channel role setup errors after pushing the channel into a
bridge. The channel may behave incorrectly in the bridge but we can no
longer abort the push at this time.
Change-Id: I08a97082b729052ee65cdca6bb730cf1289ede00
Failed registration using PJSIP/Realtime if one of the codec name
in allow/disallow option is wrong or contains space.
This patch strip codec name.
ASTERISK-25914
Change-Id: Ifdf02de94e5ddbce305640f6f0666084a3b9283d
Locking some objects like sorcery objects can be tricky because the underlying
ao2 object may not be the same for all callers. For instance, two threads that
call ast_sorcery_retrieve_by_id on the same aor name might actually get 2
different ao2 objects if the underlying wizard had to rehydrate the aor from a
database. Locking one ao2 object doesn't have any effect on the other even if
those objects had locks in the first place.
Named locks allow access control by keyspace and key strings. Now an "aor"
named "1000" can be locked and any other thread attempting to lock "aor" "1000"
will wait regardless of whether the underlying ao2 object is the same or not.
Mutex and rwlocks are supported.
This capability will initially be used to lock an aor when multiple threads may
be attempting to prune expired contacts from it.
Change-Id: If258c0b7f92b02d07243ce70e535821a1ea7fb45
The problem is ast_frdup() does not copy whole frame.subclass for voice,
video and image frames, only the format is copied. For video frames, the
subclass structure contains the .frame_ending flag used to put the RTP
marker where it needs to be.
ASTERISK-25894 #close
Change-Id: I812ca90e84ed5d4f473b997d0dd0d3c5a915fe33
In sorcery based config files where there are multiple categories with the same
name, you can't use the (+) operator to reliably append to a category because
config.c stops looking when it finds the first one with the same name.
Example:
[1000]
type = endpoint
[1000]
type = aor
[1000](+)
authenticate_qualify = yes
This config will fail because config.c appends authenticate_qualify to the
first category it finds, the endpoint, and that's not valid for endpoint.
Solution:
The capability to find a category that contains a certain variable already
exists so the only real change was to parse anything after the '+' that's not a
comma, as a filter string.
[1000]
type = endpoint
[1000]
type = aor
[1000](+type=aor)
authenticate_qualify = yes
This now works as expected.
Although the following example doesn't make any sense for pjsip, you can even
specify multiple filters:
[1000](+type=aor&qualify_frequency=10)
ASTERISK-25868 #close
Reported-by: Nick Repin
Change-Id: I10773da4c79db36fbf1993961992af63d3441580
String fields are great, except that you can't add new ones without breaking
ABI compatibility because it shifts down everything else in the structure.
The only alternative is to add your own char * field to the end of the
structure and manage the memory yourself which isn't ideal, especially since
you then can't use the OPT_STRINGFIELD_T type.
Background:
The reason string fields had to be declared inside the
AST_DECLARE_STRING_FIELDS block was to facilitate iteration over all declared
fields for initialization, compare and copy. Since AST_DECLARE_STRING_FIELDS
declared the pool, then the fields, then the manager, you could use the offsets
of the pool and manager and iterate over the sequential addresses in between to
access the fields. The actual pool, field allocation and field set operations
don't actually care where the field is. It's just iteration over the fields
that was the problem.
Solution: Extended String Fields
An extended string field is one that is declared outside the
AST_DECLARE_STRING_FIELDS block but still (anywhere) inside the parent
structure. Other than using AST_STRING_FIELD_EXTENDED instead of
AST_STRING_FIELD, it looks the same as other string fields. It's storage comes
from the pool and it participates in string field compare and copy operations
peformed on the parent structure. It's also a valid target for the
OPT_STRINGFIELD_T aco option type.
Implementation:
To keep track of the extended fields and make sure that ABI isn't broken, the
existing embedded_pool pointer in the manager structure was repurposed to be a
pointer to a separate header structure that contains the embedded_pool pointer
plus a vector of fields. The length of the manager structure didn't change and
the embedded_pool pointer isn't used in the macros, only the stringfields C
code. A side benefit of this is that changing the header structure in the
future won't break ABI.
ast_string_fields_init initializes the normal string fields and appends them to
the vector, and subsequent calls to ast_string_field_init_extended initialize
and append the extended fields. Cleanup, ast_string_fields_cmp, and
ast_string_fields_copy can now work on the vector instead of sequentially
traversing the addresses between the pool and manager.
The total size of a structure using string fields didn't change, whether using
extended fields or not, nor have the offsets of any structure members, either
inside the original block or outside. Adding an extended field to the end of a
structure is the same as adding a char *.
Details:
The stringfield C code was pulled out from utils.c and into stringfields.c.
It just made sense.
Additional work was done in ast_string_field_init and
ast_calloc_with_stringfields to handle the allocation of the new header
structure and the vector, and the associated cleanup. In the process some
additional NULL pointer checking was added.
A lot of work was done in stringfields.h since the logic for compare and copy
is there. Documentation was added as well as somne additional NULL checking.
The ability to call ast_calloc_with_stringfields with a number of structures
greater than 1 never really worked. Well, the calloc worked but there was no
way to access the additional structures or clean them up. It was agreed that
there was no use case for requesting more than 1 structure so an ast_assert
was added to prevent it and the iteration code removed.
Testing:
The stringfield unit tests were updated to test both normal and extended
fields. Tests for ast_string_field_ptr_set_by_fields and
ast_calloc_with_stringfields were also added.
As an ABI test, 13 was compiled from git and the res_pjsip_* modules, except
res_pjsip itself, saved off. The patch was then added and a full compile and
install was performed. Then the older res_pjsip_* moduled were copied over the
installed versions so res_pjsip was new and the rest were old. No issues.
contact->aor, which is a char * at the end of contact, was then changed to an
extended string field and a recompile and reinstall was performed, again
leaving stock versions of the the res_pjsip_* modules. Again, no issues with
the res_pjsip_* modules using the old stringfield implementation and with
contact->aor as a char *, and res_pjsip itself using the new stringfield
implementation and contact->aor being an extended string field.
Finally, several existing string fields were converted to extended string
fields to test OPT_STRINGFIELD_T. Again, no issues.
Change-Id: I235db338c5b178f5a13b7946afbaa5d4a0f91d61
LDCONFIG apparently isn't set to something sane on all systems so the creation
of the shared library links fails. Instead of just testing for non-blank,
main/Makefile now checks that LDCONFIG is actually executable and reverts to
LN if it isn't.
This applies to both libasteriskpj and libasteriskssl.
Thanks to 'abelbeck' for pointing out that the issue was LDCONFIG.
ASTERISK-25873 #close
Reported-by: Hans van Eijsden
Change-Id: I25b76379bc637726ec044b2c0e709b56b3701729
Asterisk uses separate UDP ports for RTP and RTCP traffic and RFC 5764
explicitly states:
There MUST be a separate DTLS-SRTP session for each distinct pair of
source and destination ports used by a media session
This means RTP keying material cannot be used for DTLS RTCP, which was
the reason why RTCP encryption would fail.
ASTERISK-25642
Change-Id: I7e8779d8b63e371088081bb113131361b2847e3a
Blind transfers to a recognized parking extension need to use the parker's
channel variable values to create the dynamic parking lot. This is
because there is always only one parker while the parkee may actually be a
multi-party bridge. A multi-party bridge can never supply the needed
channel variables to create the dynamic parking lot. In the multi-party
bridge blind transfer scenario, the parker's CHANNEL(parkinglot) value and
channel variables are inherited by the local channel used to park the
bridge.
* In park_common_setup(), make use the parker instead of the parkee to
supply the dynamic parking lot channel variable values. In all but one
case, the parkee is the same as the parker. However, in the recognized
parking extension blind transfer scenario for a two party bridge they are
different channels. For consistency, we need to use the parker channel.
* In park_local_transfer(), pass the CHANNEL(parkinglot) value to the
local channel when blind transferring a multi-party bridge to a recognized
parking extension.
* When a local channel starts a call, the Local;2 side needs to inherit
the CHANNEL(parkinglot) value from Local;1.
The DTMF one-touch parking case wasn't even trying to create dynamic
parking lots before it aborted the attempt.
* In parking_park_call(), add missing code to create a dynamic parking
lot.
A DTMF bridge hook is documented as returning -1 to remove the hook.
Though the hook caller is really coded to accept non-zero. See the
ast_bridge_hook_callback typedef.
* In feature_park_call(), don't remove the DTMF one-touch parking hook
because of an error.
ASTERISK-24605 #close
Reported by: Philip Correia
Patches:
call_park.patch (license #6672) patch uploaded by Philip Correia
Change-Id: I221d3a8fcc181877a1158d17004474d35d8016c9
There were a number of places in the res_pjsip stack that were getting
all endpoints or all aors, and then filtering them locally.
A good example is pjsip_options which, on startup, retrieves all
endpoints, then the aors for those endpoints, then tests the aors to see
if the qualify_frequency is > 0. One issue was that it never did
anything with the endpoints other than retrieve the aors so we probably
could have skipped a step and just retrieved all aors. But nevermind.
This worked reasonably well with local config files but with a realtime
backend and thousands of objects, this was a nightmare. The issue
really boiled down to the fact that while realtime supports predicates
that are passed to the database engine, the non-realtime sorcery
backends didn't.
They do now.
The realtime engines have a scheme for doing simple comparisons. They
take in an ast_variable (or list) for matching, and the name of each
variable can contain an operator. For instance, a name of
"qualify_frequency >" and a value of "0" would create a SQL predicate
that looks like "where qualify_frequency > '0'". If there's no operator
after the name, the engines add an '=' so a simple name of
"qualify_frequency" and a value of "10" would return exact matches.
The non-realtime backends decide whether to include an object in a
result set by calling ast_sorcery_changeset_create on every object in
the internal container. However, ast_sorcery_changeset_create only does
exact string matches though so a name of "qualify_frequency >" and a
value of "0" returns nothing because the literal "qualify_frequency >"
doesn't match any name in the objset set.
So, the real task was to create a generic string matcher that can take a
left value, operator and a right value and perform the match. To that
end, strings.c has a new ast_strings_match(left, operator, right)
function. Left and right are the strings to operate on and the operator
can be a string containing any of the following: = (or NULL or ""), !=,
>, >=, <, <=, like or regex. If the operator is like or regex, the
right string should be a %-pattern or a regex expression. If both left
and right can be converted to float, then a numeric comparison is
performed, otherwise a string comparison is performed.
To use this new function on ast_variables, 2 new functions were added to
config.c. One that compares 2 ast_variables, and one that compares 2
ast_variable lists. The former is useful when you want to compare 2
ast_variables that happen to be in a list but don't want to traverse the
list. The latter will traverse the right list and return true if all
the variables in it match the left list.
Now, the backends' fields_cmp functions call ast_variable_lists_match
instead of ast_sorcery_changeset_create and they can now process the
same syntax as the realtime engines. The realtime backend just passes
the variable list unaltered to the engine. The only gotcha is that
there's no common realtime engine support for regex so that's been noted
in the api docs for ast_sorcery_retrieve_by_fields.
Only one more change to sorcery was done... A new config flag
"allow_unqualified_fetch" was added to reg_sorcery_realtime.
"no": ignore fetches if no predicate fields were supplied.
"error": same as no but emit an error. (good for testing)
"yes": allow (the default);
"warn": allow but emit a warning. (good for testing)
Now on to res_pjsip...
pjsip_options was modified to retrieve aors with qualify_frequency > 0
rather than all endpoints then all aors. Not only was this a big
improvement in realtime retrieval but even for config files there's an
improvement because we're not going through endpoints anymore.
res_pjsip_mwi was modified to retieve only endpoints with something in
the mailboxes field instead of all endpoints then testing mailboxes.
res_pjsip_registrar_expire was completely refactored. It was retrieving
all contacts then setting up scheduler entries to check for expiration.
Now, it's a single thread (like keepalive) that periodically retrieves
only contacts whose expiration time is < now and deletes them. A new
contact_expiration_check_interval was added to global with a default of
30 seconds.
Ross Beer reports that with this patch, his Asterisk startup time dropped
from around an hour to under 30 seconds.
There are still objects that can't be filtered at the database like
identifies, transports, and registrations. These are not going to be
anywhere near as numerous as endpoints, aors, auths, contacts however.
Back to allow_unqualified_fetch. If this is set to yes and you have a
very large number of objects in the database, the pjsip CLI commands
will attempt to retrive ALL of them if not qualified with a LIKE.
Worse, if you type "pjsip show endpoint <tab>" guess what's going to
happen? :) Having a cache helps but all the objects will have to be
retrieved at least once to fill the cache. Setting
allow_unqualified_fetch=no prevents the mass retrieve and should be used
on endpoints, auths, aors, and contacts. It should NOT be used for
identifies, registrations and transports since these MUST be
retrieved in bulk.
Example sorcery.conf:
[res_pjsip]
endpoint=config,pjsip.conf,criteria=type=endpoint
endpoint=realtime,ps_endpoints,allow_unqualified_fetch=error
ASTERISK-25826 #close
Reported-by: Ross Beer
Tested-by: Ross Beer
Change-Id: Id2691e447db90892890036e663aaf907b2dc1c67
The configuration unsigned integer option handler sets flags for the
parser as if the option should be a signed integer (PARSE_INT32),
leading to errors on "out of range" values. Fix flags (PARSE_UINT32).
A fix to res_pjsip is also present which stops invalid flags from
being passed when registering sorcery object fields for qualify
status.
ASTERISK-25612 #close
Change-Id: I96b539336275e0e72a8e8033487d2c3344debd3e
During stress testing, we have frequently seen crashes occur because a
CLI or AMI command attempts to access information that is in the process
of being destroyed.
When addressing how to fix this issue, we initially considered fixing
individual crashes we observed. However, the changes required to fix
those problems would introduce considerable overhead to the nominal
case. This is not reasonable in order to prevent a crash from occurring
while Asterisk is already shutting down.
Instead, this change makes it so AMI and CLI commands cannot be executed
if Asterisk is being shut down. For AMI, this is absolute. For CLI,
though, certain commands can be registered so that they may be run
during Asterisk shutdown.
ASTERISK-25825 #close
Change-Id: I8887e215ac352fadf7f4c1e082da9089b1421990
The fix to ASTERISK-25407 introduced the usage of LOG_MAKEPRI. However
this macro is broken in older glibc (< 2.17); it would left-shift the
facility a second time, causing the resultant priority to become
invalid.
The syslog manpage mentions nothing about LOG_MAKEPRI and suggests this:
The priority argument is formed by ORing the facility and the level
values [...].
ASTERISK-25510 #close
Reported by: Michael Newton
Change-Id: Ia89debe7fac5ad090c7ef595c0707f31bb1e3d03
This patch is part of a series to resolve deadlocks in chan_sip.c.
* Updated sched unit test to check new behavior.
ASTERISK-25023
Change-Id: Ib69437327b3cda5e14c4238d9ff91b2531b34ef3
Channel masquerading had a conflict with autochannel locking.
When locking autochannel->channel, the channel is fetched from the
autochannel and then locked. During the fetch, the autochannel -- which
has no locks itself -- can be modified by someone who owns the channel
lock. That means that the value of autochan->channel cannot be trusted
until you hold the lock.
In practice, this caused problems with Local channels getting
masqueraded away while the ChanSpy attempted to get info from that
channel. The old channel which was about to get removed got locked, but
the new (replaced) channel got unlocked (no-op). Because the replaced
channel was now locked (and would never get unlocked), it couldn't get
removed from the channel list in a timely manner, and would now cause
deadlocks when iterating over the channel list.
This change checks the autochannel after locking the channel for changes
to the autochannel. If the channel had been changed, the lock is
reobtained on the new channel.
In theory it seems possible that after this fix, the lock attempt on the
old (wrong) channel can be on an already destroyed lock, maybe causing
a crash. But that hasn't been observed in the wild and is harder induce
than the current deadlock.
Thanks go to Filip Frank for suggesting a fix similar to this and
especially to IRC user hexanol for pointing out why this deadlock was
possible and testing this fix. And to Richard for catching my rookie
while loop mistake ;)
ASTERISK-25321 #close
Change-Id: I293ae0014e531cd0e675c3f02d1d118a98683def
Although we use the RTLD_LAZY flag when calling dlopen
the first time on a module, this only defers resolution
for function calls. Pointer references to functions are
determined at link time so dlopen expects them to be there.
Since we don't cross-module link, pointers to functions
in other modules won't be available and dlopen will fail.
Doing a "hardened" build also causes problems because it
typically sets "-z now" on the ld command line which
overrides RTLD_LAZY at run time.
If the failing module isn't a GLOBAL_SYMBOLS module, then
dlopen will be called again after all the GLOBAL_SYMBOLS
modules have been loaded and they'll eventually resolve.
If the calling module IS a GLOBAL_SYMBOLS module itself
and a third module depends on it, then there's an issue
because the second time through the dlopen loop,
GLOBAL_SYMBOLS modules aren't given any special treatment
and since the order in which dlopen is called isn't
deterministic, the dependent may again be tried before the
module it needs is loaded.
Simple solution: Save modules that fail load_resource
because of a dlopen error in a list and retry them
immediately after the first pass. Keep retrying until
the failed list is empty or we reach a #defined max
retries. Error messages are suppressed until the final
pass which also gets rid of those confusing error messages
about module failures that are later corrected.
Change-Id: Iddae1d97cd2f00b94e61662447432765755f64bb
It's possible for the transferer channel to get hung up early during the
attended transfer process. For instance, a phone may send a "bye" immediately
upon receiving a sip notify that contains a sip frag 100 (I'm looking at you
Jitsi). When this occurs a race begins between the transferer being hung up
and completion of the transfer code.
If the channel hangs up too early during a transfer involving stasis bridging
for instance, then when the created local channel goes to look up its swap
channel (and associated datastore) it can't find it (since it is no longer in
the bridge) thus it fails to enter the stasis application. Consequently, the
created local channel(s) hang up as well. If the timing is just right then the
bridging code attempts to add the message link with missing local channel(s).
Hence the crash.
Unfortunately, there is no great way to solve the problem of the unexpected
"bye". While we can't guarantee we won't receive an early hangup, and in this
case still fail to enter the stasis application, we can make it so asterisk
does not crash.
This patch does just that by locking the local channel structure, checking
that the local channel's peer has not been lost, and then continuing. This
keeps the local channel's peer from being ripped out from underneath it by
the local/unreal hangup code while attempting to set the stasis message link.
ASTERISK-25771
Change-Id: Ie6d6061e34c7c95f07116fffac9a09e5d225c880
In message.c, if msg_alloc fails to init the string field,
vars may be null, so use a null tolerant cleanup.
In res_pjsip_messaging.c, if msg_data_create fails, mdata
will be null, so use a null tolerant cleanup.
ASTERISK-25323
Change-Id: Ic2d55c2c3750d5616e2a05ea92a19c717507ff56
Previous chan_sip behavior:
Before this patch chan_sip would always strip any quotes from an incoming
reason and pass that value up as the REDIRECTING(reason). For an outgoing
reason value, chan_sip would check the value against known values and
quote any it didn't recognize. Incoming 480 response message reason text
was just assigned to the REDIRECTING(reason).
Previous chan_pjsip behavior:
Before this patch chan_pjsip would always pass the incoming reason value
up as the REDIRECTING(reason). For an outgoing reason value, chan_pjsip
would send the reason value as passed down.
With this patch:
Both channel drivers match incoming reason values with values documented
by REDIRECTING(reason) and values documented by RFC5806 regardless of
whether they are quoted or not. RFC5806 values are mapped to the
equivalent REDIRECTING(reason) documented value and is set in
REDIRECTING(reason). e.g., an incoming RFC5806 'unconditional' value or a
quoted string version ('"unconditional"') is converted to
REDIRECTING(reason)'s 'cfu' value. The user's dialplan only needs to deal
with 'cfu' instead of any of the aliases.
The incoming 480 response reason text supported by chan_sip checks for
known reason values and if not matched then puts quotes around the reason
string and assigns that to REDIRECTING(reason).
Both channel drivers send outgoing known REDIRECTING(reason) values as the
unquoted RFC5806 equivalent. User custom values are either sent as is or
with added quotes if SIP doesn't allow a character within the value as
part of a RFC3261 Section 25.1 token. Note that there are still
limitations on what characters can be put in a custom user value. e.g.,
embedding quotes in the middle of the reason string is silly and just
going to cause you grief.
* Setting a REDIRECTING(reason) value now recognizes RFC5806 aliases.
e.g., Setting REDIRECTING(reason) to 'unconditional' is converted to the
'cfu' value.
* Added missing malloc() NULL return check in res_pjsip_diversion.c
set_redirecting_reason().
* Fixed potential read from a stale pointer in res_pjsip_diversion.c
add_diversion_header(). The reason string needed to be copied into the
tdata memory pool to ensure that the string would always be available.
Otherwise, if the reason string returned by reason_code_to_str() was a
user's reason string then the string could be freed later by another
thread.
Change-Id: Ifba83d23a195a9f64d55b9c681d2e62476b68a87
Background here:
http://lists.digium.com/pipermail/asterisk-dev/2016-January/075266.html
From CHANGES:
* To help insure that Asterisk is compiled and run with the same known
version of pjproject, a new option (--with-pjproject-bundled) has been
added to ./configure. When specified, the version of pjproject specified
in third-party/versions.mak will be downloaded and configured. When you
make Asterisk, the build process will also automatically build pjproject
and Asterisk will be statically linked to it. Once a particular version
of pjproject is configured and built, it won't be configured or built
again unless you run a 'make distclean'.
To facilitate testing, when 'make install' is run, the pjsua and pjsystest
utilities and the pjproject python bindings will be installed in
ASTDATADIR/third-party/pjproject.
The default behavior remains building with the shared pjproject
installation, if any.
Building:
All you have to do is include the --with-pjproject-bundled option on
the ./configure command line (and remove any existing --with-pjproject
option if specified). Everything else is automatic.
Behind the scenes:
The top-level Makefile was modified to include 'third-party' in the
list of MOD_SUBDIRS.
The third-party directory was created to contain any third party
packages that may be needed in the future. Its Makefile automatically
iterates over any subdirectories passing on targets.
The third-party/pjproject directory was created to house the pjproject
source distribution. Its Makefile contains targets to download, patch
configure, generate dependencies, compile libs, apps and python bindings,
sanitized build.mak and generate a symbols list.
When bootstrap.sh is run, it automatically includes the configure.m4
file in third-party/pjproject. This file has a macro to download and
conifgure pjproject and get and set PJPROJECT_INCLUDE, PJPROJECT_DIR
and PJPROJECT_BUNDLED. It also tests for the capabilities like
PJ_TRANSACTION_GRP_LOCK by parsing preprocessor output as opposed to
trying to compile. Of course, bootstrap.sh is only run once and the
configure file is incldued in the patch.
When configure is run with the new options, the macro in configure.m4
triggers the download, patch, conifgure and tests. No compilation is
performed at this time. The downloaded tarball is cached in /tmp so
it doesn't get downloaded again on a distclean.
When make is run in the top-level Asterisk source directory, it will
automatically descend all the subdirectories in third_party just as it
does for addons, apps, etc. The top-level Makefile makes sure that
the 'third-party' is built before 'main' so that dependencies from the
other directories are built first.
When main does build, a new shared library (libasteriskpj) is created that
links statically to the pjproject .a files and exports all their symbols.
The asterisk binary links to that, just as it does with libasteriskssl.
When Asterisk is installed, the pjsua and pjsystest apps, and the pjproject
python bindings are installed in ASTDATADIR/third-party/pjproject. This
will facilitate testing, including running the testsuite which will be
updated to check that directory for the pjsua module ahead of the system
python library.
Modules should continue to depend on pjproject if they use pjproject APIs
directly. They should not care about the implementation. No changes to any
res_pjsip modules were made.
Change-Id: Ia7a60c28c2e9ba9537c5570f933c1ebcb20a3103
The channel is now going to get T.38 terminated when it leaves the
bridging system and the bridged peers are going to get T.38 terminated as
well.
ASTERISK-25582
Change-Id: I77a9205979910210e3068e1ddff400dbf35c4ca7
Local channel optimization could cause DTMF digits to be duplicated.
Pending DTMF end events would be posted to a bridge when the local channel
optimizes out and is replaced by the channel further down the chain. When
the real digit ends, the channel would get another DTMF end posted to the
bridge.
A -- LocalA;1/n -- LocalA;2/n -- LocalB;1 -- LocalB;2 -- B
1) LocalA has the /n flag to prevent optimization.
2) B is sending DTMF to A through the local channel chain.
3) When LocalB optimizes out it can move B to the position of LocalB;1
4) Without this patch, when B swaps with LocalB;1 then LocalB;1 would
settle an owed DTMF end to the bridge toward LocalA;2.
5) When B finally ends its DTMF it sends the DTMF end down the chain.
6) Without this patch, A would hear the DTMF digit end when LocalB
optimizes out and when B ends the original digit.
ASTERISK-25582
Change-Id: I1bbd28b8b399c0fb54985a5747f330a4cd2aa251
Frame hooks can conceivably return a control frame in exchange for an
audio frame inside ast_write(). Those returned control frames were not
handled quite the same as if they were sent to ast_indicate(). Now it
doesn't matter if you use ast_write() to send an AST_FRAME_CONTROL to a
channel or ast_indicate().
ASTERISK-25582
Change-Id: I5775f41421aca2b510128198e9b827bf9169629b
The ast_sorcery_create, update and delete function have been refactored
to better deal with caches and errors.
The action is now called on all non-caching wizards first. If ANY succeed,
the action is called on all caching wizards and the observers are notified.
This way we don't put something in the cache (or update or delete) before
knowing the action was performed in at least 1 backend and we only call the
observers once even if there were multiple writable backends.
ast_sorcery_create was never adding to caches in the first place which
was preventing contacts from getting added to a memory_cache when they
were created. In turn this was causing memory_cache to emit errors if
the contact was deleted before being retrieved (which would have
populated the cache).
ASTERISK-25811 #close
Reported-by: Ross Beer
Change-Id: Id5596ce691685a79886e57b0865888458d6e7b46
The return type of ast_cel_track_event() is not large enough to return all
64 potential bits of the event enable mask. Fortunately, the defined CEL
events do not really need all 64 bits and the return value is only used to
determine if the requested CEL event is enabled.
* Made the ast_cel_track_event() return 0 or 1 only so the return value
can fit inside an int type instead of zero or a truncated 64 bit non-zero
value.
Change-Id: I783d932320db11a95c7bf7636a72b6fe2566904c
listener() opens the same code block in two places (#if and #else). This
confuses some folding editors causing it to think that an extra code block
was opened. Folding in 'geany' causes all code after listener() to be
folded as if it were part of that procedure.
ASTERISK-24813 #close
Change-Id: I4b8c766e6c91e327dd445e8c18f8a6f268acd961
The SSL_OP_NO_TLSv1_1 and SSL_OP_NO_TLSv1_2 defines did not exist prior
to OpenSSL version 1.0.1. A recent commit attempts to, by default, set
these options, which can cause problems on systems with older OpenSSL
installations.
This commit adds a configure script check for those defines and will not
attempt to make use of those if they do not exist. We will print a
warning urging the user to upgrade their OpenSSL installation if those
defines are not present.
Change-Id: I6a2eb9a43fd0738b404d8f6f2cf4b5c22d9d752d
Sending UDPTL packets to Asterisk with the right amount of missing
sequence numbers and enough redundant 0-length IFP packets, can make
Asterisk crash.
ASTERISK-25603 #close
Reported by: Walter Doekes
ASTERISK-25742 #close
Reported by: Torrey Searle
Change-Id: I97df8375041be986f3f266ac1946a538023a5255
This change exposes the configuration of various aspects of the TLS
support and sets the default to the modern standards.
The TLS cipher is now set to the best values according to the
Mozilla OpSec team, different TLS versions can now be disabled, and
the cipher order can be forced to be that of the server instead of
the client.
ASTERISK-24972 #close
Change-Id: I0a10f2883f7559af5e48dee0901251dbf30d45b8
The config options framework is strict in that configuration options must
be documented unless XML documentation support is not available. In
practice this is useful as it ensures documentation exists however in
off-nominal cases this can cause strange problems.
If it is expected that a config option has a non-zero or non-empty
default value but the config option documentation is unavailable
this reasonable expectation will not be met. This can cause obscure
crashes and weirdness depending on how the code handles it.
This change tweaks the behavior to ensure that the config option
is still allowed to register, apply default values, and be set when
devmode is not enabled. If devmode is enabled then the option can
NOT be set.
This also does not remove the initial documentation error message that
is output on load when registering the configuration option.
ASTERISK-25725 #close
Change-Id: Iec42fca6b35f31326c33fcdc25473f6fd7bc8af8
The null terminator of the tail struct member was not being allocated
when no logger.conf config file is installed.
ASTERISK-25714 #close
Reported by: Badalian Vyacheslav
Change-Id: I45770fdd08af39506a3bc33ba279c4f16e047a30
Make sure buf[res] is not accessed at res=-1 (buffer underrun).
Address Sanitizer will complain about this quite loudly.
ASTERISK-24801 #close
Change-Id: Ifcd7f691310815a31756b76067c56fba299d3ae9
You have to call ast_taskprocessor_unref() outside of the taskprocessor
implementation code. Taskprocessor use since v12 has become more
transient than just the singleton uses in earlier versions.
Change-Id: If7675299924c0cc65f2a43a85254e6f06f2d61bb
The xferfailsound was read from the channel at the beginning of the transfer,
and that value is "cached" for the duration of the transfer. Therefore, changing
the xferfailsound on the channel using the FEATURE() dialplan function does
nothing once the transfer is under way.
This makes it so the transfer code instead gets the xferfailsound configuration
options from the channel when it is actually going to be used.
This patch also fixes a potential memory leak of the props object as well as
making sure the condition variable gets initialized before being destroyed.
ASTERISK-25696 #close
Change-Id: Ic726b0f54ef588bd9c9c67f4b0e4d787934f85e4
* Add freed regions totals to allocations and summary.
* Add totals for all allocations and not just the selected allocations.
Change-Id: I61d5a5112617b0733097f2545a3006a344b4032a
If the attended transfer destination answers (picks call up or goes to
voicemail) and then hangs up on the transferer then transferer hears the
fail sound.
This patch makes it so the fail sound is not played when the transfer
destination/target hangs up after answering.
ASTERISK-25697 #close
Change-Id: I97f142fe4fc2805d1a24b7c16143069dc03d9ded
This issue was exposed when executing a connected line subroutine.
When connected or redirected subroutines or macros are executed it is
expected that the underlying applications and logic invoked are fast
and do not consume frames. In practice this constraint is not enforced
and if not adhered to will cause channels to continue when they shouldn't.
This is because each caller of the connected or redirected logic does not
check whether the channel has been hung up on return. As a result the
the hung up channel continues.
This change makes it so when the API to execute a subroutine or
macro is invoked the channel is checked to determine if it has hung up.
If it has then a hangup is queued again so the caller will see it
and stop.
ASTERISK-25690 #close
Change-Id: I1f9a8ceb1487df0389f0d346ce0f6dcbcaf476ea
* changes:
Sorcery: Create human friendly serializer names.
Stasis: Create human friendly taskprocessor/serializer names.
taskprocessor.c: New API for human friendly taskprocessor names.
taskprocessor.c: Sort CLI "core show taskprocessors" output.
Recent changes (ASTERISK-25394 commit 2bd27d1222)
introduced the possibility of a deadlock. Due to the mentioned modifications
ast_change_hints now needs to keep both merge/delete and state callbacks from
occurring while it executes. Unfortunately, sometimes ast_change_hints can be
called with the contexts container locked. When this happens it's possible for
another thread to grab the context_merge_lock before the thread calling into
ast_change_hints does and then try to obtain the contexts container lock. This
of course causes a deadlock between the two threads. The thread calling into
ast_change_hints waits for the other thread to release context_merge_lock and
the other thread is waiting on that one to release the contexts container lock.
Unfortunately, there is not a great way to fix this problem. When hints change,
the subsequent state callbacks cannot run at the same time as a merge/delete,
nor when the usual state callbacks do. This patch alleviates the problem by
having those particular callbacks (the ones run after a hint change) occur in a
serialized task. By moving the context_merge_lock to a task it can now safely be
attempted or held without a deadlock occurring.
ASTERISK-25640 #close
Reported by: Krzysztof Trempala
Change-Id: If2210ea241afd1585dc2594c16faff84579bf302
* Add new API call to get a sequence number for use in human friendly
taskprocessor names.
* Add new API call to create a taskprocessor name in a given buffer and
append a sequence number.
Change-Id: Iac458f05b45232315ed64aa31b1df05b875537a9
Update the CLI "core show taskprocessors" output format to not be
distorted because UUID names are longer than previously used taskprocessor
names.
Change-Id: I1a5c82ce3e8f765a0627796aba87f8f7be077601
The CLI "core ping taskprocessor" command does not work very
well with taskprocessor names that have spaces in them. You
have to put quotes around the name so using tab completion
becomes awkward.
Change-Id: I29e806dd0a8a0256f4e2e0a7ab88c9e19ab0eda0
This resolves a reference leak caused by ASTERISK-25535. The pointer
returned by ast_format_get_codec is saved so it can be released.
ASTERISK-25664 #close
Change-Id: If9941b1bf4320b2c59056546d6bce9422726d1ec
The 11/13 branches and master use 2 different file version macros. 11/13
uses ASTERISK_FILE_VERSION but master uses ASTERISK_REGISTER_FILE. This
means a new file added to 11/13 can't just be cherry-picked to master
because the macro has to be changed.
To make cherry-picking possible, ASTERISK_REGISTER_FILE was added
to asterisk.h as a simple alias for ASTERISK_FILE_VERSION(__FILE__, NULL)
The "$Revision$" tag doesn't do anything since Asterisk moved to git so
just passing NULL as the verison works fine. asterisk.h was also
annotated to deprecate ASTERISK_FILE_VERSION and suggest using
ASTERISK_REGISTER_FILE for all new files.
Finally, 2 recent file additions, pbx_builtins.c and pbx_functions.c,
were modified to use the new macro to make sure it actually worked.
'core show file version' showed the correct output.
Change-Id: I5867ed898818d26ee49bb6e5c7d4c1a45d4789a5
Somehow stasis_cache_pattern got out of sync between 13 and master
and it was causing duplicate channel message issues in 13 when
related to a specific endpoint. I.E. from statsd,
'endpoints.PJSIP.1174.channels 0|g' was being emitted twice.
Backporting stasis_cache_pattern from master to 13 solved
the issue and running the unit and testsuite tests confirmed
that no new ones were created.
ASTERISK-25317 #close
Change-Id: Ia8707462f62d15eed14541c37f332a7bbbceb548
This is the sixth patch in a series meant to reduce the bulk of pbx.c.
This moves hangup handler management functions to their own source.
Change-Id: Ib25a75aa57fc7d5c4294479e5cc46775912fb104
This is the sixth patch in a series meant to reduce the bulk of pbx.c.
This moves dialplan application management functions to their own source.
Change-Id: I444c10fb90a3cdf9f3047605d6a8aad49c22c44c
This is the fifth patch in a series meant to reduce the bulk of pbx.c.
This moves ast_switch functions to their own source.
Change-Id: Ic2592a18a5c4d8a3c2dcf9786c9a6f650a8c628e
Richard Mudgett
Joshua Colp
Alexei Gradinari
Jaco Kroon
zuul
George Joseph
Jacek Konieczny
Gianluca Merlo
Mark Michelson
Walter Doekes
Kevin Harwell
Scott Griepentrog
Corey Farrell
Diederik de Groot
Matt Jordan